ขนาดวิดีโอ: 1280 X 720853 X 480640 X 360
แสดงแผงควบคุมโปรแกรมเล่น
เล่นอัตโนมัติ
เล่นใหม่
√ Watch the Video√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts√ Do it Yourself√ Save Money
Thankful for your videos been working on my 08 impala all week and you’re the only one who goes into enough detail.
Changed the sway bar i see as well at the end, nice
So…. How’d you get the ball joint out the knuckle??
My new control arms say "Avoid premature bushing wear. Do not fully tighten bushing until suspension is at ride height." What are your thoughts?
Nice job!!! I was trying to get the control arm back in and realized the strut is forcing it short of mounting the bolts. Im like "how they do this", then Im like "duh...a strap" Thanks...I'm a bit stupid today!
Thanx for this video. Im doin it myself got all my parts. So ill comment again once its all done.
+DeanOh Ocampo Thanks for the feedback! 1aau.to/m/Shop-TRQ
How did you torque down the ball joint nut never seen it
Good information
Great job!
So i think i didn't tight to bolt to tight but i got the pin through will that be a problem its pretty
pre load?
Why would you need an alignment done, you didnt touch the tie rods?
+ch hansen It is always suggested to have an alignment performed after replacing any suspension parts for optimal performance.
I need to replace the plastic harness fasteners.
Can I get this tight enough without an air ratchet?
no camber?
Mann how you took the tire off in a circle made me cringe always use a star pattern 😐
7:46 yeah right buddy your not that strong 😂😂😂
You jump into everything and never say what size bolt
this isnt even an impala in the video
![[LIVE] : ONE ลุมพินี 89 | คู่เอก "ยอดไอคิว vs คิริลล์"](http://i.ytimg.com/vi/Z3vYkHJ_5Ig/mqdefault.jpg)
√ Watch the Video
√ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts
√ Do it Yourself
√ Save Money
Thankful for your videos been working on my 08 impala all week and you’re the only one who goes into enough detail.
Changed the sway bar i see as well at the end, nice
So…. How’d you get the ball joint out the knuckle??
My new control arms say "Avoid premature bushing wear. Do not fully tighten bushing until suspension is at ride height." What are your thoughts?
Nice job!!! I was trying to get the control arm back in and realized the strut is forcing it short of mounting the bolts. Im like "how they do this", then Im like "duh...a strap" Thanks...I'm a bit stupid today!
Thanx for this video. Im doin it myself got all my parts. So ill comment again once its all done.
+DeanOh Ocampo Thanks for the feedback! 1aau.to/m/Shop-TRQ
How did you torque down the ball joint nut never seen it
Good information
Great job!
So i think i didn't tight to bolt to tight but i got the pin through will that be a problem its pretty
pre load?
Why would you need an alignment done, you didnt touch the tie rods?
+ch hansen It is always suggested to have an alignment performed after replacing any suspension parts for optimal performance.
I need to replace the plastic harness fasteners.
Can I get this tight enough without an air ratchet?
no camber?
Mann how you took the tire off in a circle made me cringe always use a star pattern 😐
7:46 yeah right buddy your not that strong 😂😂😂
You jump into everything and never say what size bolt
this isnt even an impala in the video