Had a van with a similar problem with the A/C Compressor clutch would engage than drop out. The wire from the distributor to the A/C module was shorted to ground. The vehicle was a Toyota Hiace I believe you dont have them in US
very good diagnose. I have 1997 toyota forklift same problem I test valve resistance was ok I changed regulator stiil same .after workiing die I need your helpe
I have a Toyota lift I’m working on , dies when turning , 3 techs from a Toyota lift dealer looked at it and can’t figure it out , they installed a new vaporizer and runs good till you turn it.
I'm working on a Nissan Forklift and on the dash it's got one of the an idiot light keeps showing this little picture of like a little bowl with a stringly line through it and on the left side of it like an arrow so I don't know what that means do you know what that symbol is
@@forkliftgeek10 the seat switch wires got pulled out so I wire them together until I get a new c switch for it but it still shows that little bowl like a with a squiggly line and on the left side of it that little arrow with a line in the back of the arrow triangle it still moves forward and reverse and goes up and down. Could it still be sensing the seat switch even if it's wired together to bypass the seat switch
If you don't know, you just don't know!!! My moto is, if you don't know,, ask someone who does. Would you rather know a little bit about a lot? Or a lot about a little bit?
I've been work at a Toyota lift dealer for over 2 years now and I've learned more of these videos. Thank you for sharing your knowledge 👍🏾
Are you kidding me!!! Thank you so freaking much. I had done everything I could think of. You fixed my problem in less than sixty seconds
Great job hunting down the problem, that was awesome.
I ran into a similar issue on a Tennant M20 Sweeper / Scrubber. Great troubleshooting my man!
Thanks, I deal with these all the time and not seen this fault, great work!
Appreciate a technic of your work God bless you. learnt from your videos so many time saving tricks at work.
Love your tech videos! Thanks from a fellow forklift tech.
being an auto enthusiast that was so satisfying to watch
Great troubleshooting technique. I work on Yale Lift Trucks LP engine. I will keep that diagnosis in mind if i ever come into that type of scenario.
Very good use of the scope. Tks.
Excellent video keep up the good work
Great job sir.....🔥🔥
You just saved my ass bud , found the same issue
Beautiful work!
Had a van with a similar problem with the A/C
Compressor clutch would engage than drop out.
The wire from the distributor to the A/C module was shorted to ground.
The vehicle was a Toyota Hiace
I believe you dont have them in US
would love to see more videos from your channel
Great video, thanks for sharing. If you need any Pico support let me know.
Thank you. Appreciate it.
very good diagnose. I have 1997 toyota forklift same problem I test valve resistance was ok I changed regulator stiil same .after workiing die I need your helpe
I have a Toyota lift I’m working on , dies when turning , 3 techs from a Toyota lift dealer looked at it and can’t figure it out , they installed a new vaporizer and runs good till you turn it.
Impressive. 👏🏽👏🏽👏🏽
anyone reading this could you let me inow where to get a valve cover for a 5r toyota engine? Thanks!
sharing this with my friend he will like it
keep posting more, keep up !!
Muchas gracias por el video me sirvió mucho
Great video. What’s the oscilloscope setup you got called?
Picoscope
I'm working on a Nissan Forklift and on the dash it's got one of the an idiot light keeps showing this little picture of like a little bowl with a stringly line through it and on the left side of it like an arrow so I don't know what that means do you know what that symbol is
If the forklift is not driving or lifting at all, then you are probably referring to the seat switch.
@@forkliftgeek10 the seat switch wires got pulled out so I wire them together until I get a new c switch for it but it still shows that little bowl like a with a squiggly line and on the left side of it that little arrow with a line in the back of the arrow triangle it still moves forward and reverse and goes up and down. Could it still be sensing the seat switch even if it's wired together to bypass the seat switch
You are one sharp dude.
Where do you get you re control lamp?
Matco tools
Nice job ! But couldn't you have done the wire replacement without having the added expense of a new loom or wiring harness ? 😂😂😂
I was so lost watching this video
Hi! This was a very helpful video. Where do you get wiring schematics for these forklifts? Thanks
Company provided
🔥🔥🔥
If you don't know, you just don't know!!!
My moto is, if you don't know,, ask someone who does.
Would you rather know a little bit about a lot? Or a lot about a little bit?
this was a boring video for me