@@MarcoS-yd9pf A pasta thermica deve segurar. Senão usa um pouco de cola thermica nos cantos depois de posicionado. Mas bem poquinho so pra ficar no lugar, pois, a pressão do dissipador vai manter ele no lugar.
@@MarcoS-yd9pf Nothing...the silicone used to secure it in place from factory that you cut away was only there to stop you from opening it, the new thermal paste you'll put there between the cover and the chip AND again between the cover and the heat sink (like a sandwich) will be enough to hold it in place once its all clamped down. I've done this numerous times with XBox 360's & PS3 fat's and they've never come loose. In fact, with the adherence properties that thermal paste has I've had great difficulty lifting the covers off the heat sink by hand once they're stuck down with paste...they will never ever fall off! The key is pressure, make sure you've really pressed that heat spreader (metal cover) down onto the heat sink before putting the whole lot back on top of the chip.
Thanks so much! All I did was reheat the solder on both sides of the one resistor that was giving me a bad reading and checked the ohms. That fixed it and I didn’t have to add any solder.
Omg it worked! I just bought a broken slim with flashing red light and high fan rpm, then it would shut down. Within 20 minutes it's now fixed and booting perfectly. Thanks for the awesome tutorial!
Thank you for this, I have the Xbox360 S star wars Console and exactly this happened to mine about a year ago; powers up, 10 flashes of the red light then immediately shuts down. I was going to bin it (got a used console for 25 GBP off ebay) but forgot about it. Then came across this video, dug the console out to try this fix. However, when I tested the resistors, only one was reading high (44ohms) so I only replaced that with a solder jumper and left the others alone. It was quite difficult to do, you need a steady hand, 0.3mm solder wire, a free standing magnifying glass and a thin pointed solder iron tip heated to 300 Celsius. The console powered up and is now working fine. Not sure how long it will last, but I'm grateful for this video. Thanks again.
Thank you - I had solder and have done some small projects on my car, but didn't have the correct site solder or the right tip, so this comment helped tremendously
For what it's worth. I did this on my Xbox 360 S, and it worked. I still worry about whether I have removed the console's ability to sense future overheating, but it was a fairly easy way to bring a dead $10 console back to life.
@@pullingthestrings5233 the resistors on the board read 0 ohm. Using a solder jumper will also read 0 0 ohm. There is no difference between doing this fix and putting another 0 ohm resistor on the board.
Thanks. I am not a xbox tech. I have done many things to correct. Im sure resistors is the problem. The fan wors. The power cord works. But i have reached as far as I can to solve the problem. Good instructual video.
had a Corona v2 doing this exact issue, all of the resistor polarity was off on the board, This fixed it perfectly. To anyone worried this will cause more issues, the resistors you're removing and bridging are 0 (Yes, Zero) Ohm resistors, a solder bridge is exactly the same as replacing the resistor, just without the fail rate. as long as you can solder, this should be pretty easy for you, I did it with a soldering iron that had a melting tip, took me all of 2 mins to do the bridges and 30 seconds to flow it properly and neatly. Definitely need a new soldering iron before I tackle installing an Ace v3 though, Haha. Cheers bud, Gonna double check a corona v4 I have with the same issue and see if I can fix it :D
About two years ago I had a 360 RDOD on me and had no clue this was how to fix it. I took the motherboard to my garage today and (Edit: Solder Bridged) 2 of 6 resistors and it works like new! Tysm!
@@mrnissan3262 Instead of using new resistors I created a solder bridge in place of them. From what I know, solder bridges work for resistors that require 0 ohm to work. I learned this from a different video, if I find that video I'll link it here. 👍
Mine overheats quick but i had a fan in front on the fan and it works so you can buy a fan on Amazon to but on the side of xbox its call Intercooler STS
why did they put this point of failure in these at all? one of my Xbox 360 slim had this issue and I just desoldered the resistor and bridged it. works like a charm, in fact the fan turns up less than ever before, making me think when the resistor started failing it already reported higher temps than normal. Great job!
This totally fixed my problem! Had the red dot of death (approx. 11 red blinks) with fast fan speed at startup, would not even turn on at all. Followed this guide and all is well again! I was skeptical and am not very experienced with soldering, but pulled it off with the help of your awesome video! Also, I actually do have a trinity board (no post out board), took a chance since it was screwed anyway, and this did take of the issue for my trinity. Thanks so much for this, man- much appreciated!!
wow R4D3 goes to infinte value (no working) console error 0013 turn on with a red dot and turns off in less than a minute, jumping the resistor and boot up. Thanks for the tip.
I've done this same method on a Halo corona unit i got and it hasn't worked strangely, about 4 of the resistors were reading in the high 20s-30s so i just removed all of them and bridged them, still a constant red light, but i could intermittently get a successful post by bridging r4d5 and r4d7 with some tweasers, several reflows didn't help either. Not sure where to go from here but its worth saving being a special halo 4 edition and the board has some software to give it the custom sounds.
@@tonymcpherson1958 Are the sounds linked to the main board and not the front panel board? Im looking at potentially doing a board swap do you know of a guide on how to swap these over?
@@tonymcpherson1958 ouch, was hoping I can avoid that. Is it a software job to switch these over or is it part of the hardware on the motherboard? Thanks for the help
I have a Trinity RGH , if I let it sit over night the console will stay on for about 15 mins the next time I turn it on. Then when It gives me Red dot I turn it back off and it will still give me the red dot. Does this method apply ?
Power Supply is fine, I tried multiple one still the same result . I cannot check the temp because it just gives me a Red dot BUT when I was able to get to the Dash board it said My console overheated, also the console wasnt even on that long maybe 15 mins. Replaced the Thermal paste with Artic Silver five. Still getting the red dot.
+TristinHD the resistor location is different for trinity. The solution does not apply to your console. You should check the secondary error code for your console
Thanks for the tip. Had one of these reading 70ohm and the others OK, but accidentally knocked off another resistor while removing the bad one. Couldn't get a solder ball to flow between the pads so had to cut some small strips of copper from a stranded 12ga copper wire and tin them on my iron, then peel off the iron using tweezers and place with the tweezers while heating. I have a feeling this would have been easier with some replacement 0ohm resistors but didn't have any on hand.
Was confusing because this system had bad thermal paste application under the heatspreader and originally changing that got it working but it stopped shortly.
@@sthetixofficial I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
interesting, super complex but would be improved to also replace the fan over 2000 RPM or dust clean the fan overall with replacing thermal paste that uses for PC?
just picked up an xbox 360 slim with the 11 flashing red dot + full speed fans issue. One of those resistors was 1.5 Mohms, blew them all away and replaced with solder bridges. The Xbox is back from the dead.
I have this problem on the Xbox 360 e slim, it shuts down and restarts with the fan on high speed then restarts again and runs fine. From startup it says lack of ventilation and over heating and goes though what I said every time. Is there a fix?
sthetix I have a Star Wars corana version till this day playing actual right now mw2. But I’m worried cause I don’t think it’s specific cause 6-7 years later hear it is. Dunno I had a 2010 glossy version which has the RDOD no fan speed up just plain red dot of death with normal fan so. 2011 my Star Wars version right now is actually online trying to combat these hos
If you look around you can find Chinese combo stations that are 700+ watts and they are good enough especially if you buy some better tips. $130 might sound like a lot but you'll be able to fix a lot of things.
My Xbox 360 s (RGH) has Memory overheating problem, the temperature reaches about 84 celcius degrees, and after some time (30 min) turns off. Solutions?
@@sthetixofficial I got a Corona it's brand new it's never been used it was bought and ever since been in the box I cranked the damn thing up and it runs hot I mean there's no flashing lights or anything like that the lights green but it just immediately started blowing real hot ass are right out of the top vent. It's just hot immediately after I turn it on is that normal. Doesn't seem to get any hotter but damn it's hot right off the bat. It's got maybe forty-five minutes on it total since it was bought out of the box. Thanks for any help
im having a same problem.. can you help me where do i repair my unit here in dubai?! because im scared that maybe they dont know how to fix it properly. thanks..
@@sthetixofficial i know u've jumped them, but they were put there for a reason maybe removing them put the xbox in danger later, would it be better to replace the ones that give high ohms? I sent mine for repairs, he fixed red light but cpu temp starts at 75c, he said he replaced a resistor, i m wondering if i should ask him to jump the resistor he replaced or ask him to jump all resistors. Thanks
Hi, ive got a strange problem cuz when i boot up my xbox 360 slim then normal green light shows up everything is cool but the fan is speeding like +10% in 30sec then it gets so loud and xbox just shuts of. I mean when i boot up the xbox, fan is getting louder and louder and then xbox shuts off, i dont have a red/blinking light just green like always, it shutdowns within like 4-5 minutes
My Xbox motherboard does not look like this I can’t find the specific resistors and it looks a lot different is there somehow I have a different version?
if u solder jump the resistor it should be near 0 ohm after right? because mine before solder jump 75 temp now its 65. but i forgot to check it. because i dont own a multimeter.
sthetix ok, cause only one of mine are reading high and just wanted to make sure. Cause I have the rdod with high fan, so this should hopefully fix it.
thanks for the vid, did everything u did but now the system powers up, fan spins at full speed for like five secs and then spins down. any idea what this could be?
@@sthetixofficial My friend bought an Xbox Slim overseas with 120v power supply. Is it okay to use it on 240v outlet? My country uses 220-240v output on all electronics.
maybe ill try that! I have an xbox 360 slim right here, right after i start it it shows an red ring and the fans spin at abt. 100% (almost louder than an airplane (jk)) and then it shuts off... At least i think so, didnt look on it for quite some time now...
Is their any way to avoid this problem or will it happen to all xbox360coronas I'm just concerned cuz this seems to be happening to a lot consoles and I am not very experienced with soldering
@@LenoxFilms actually my prblm is console is working perfectly but when i check temperature it's showing faulse but the console is working fine i can play all the games ....and do u understood what I'm trying to say
Hi!I have a weird problem actually.So when i start to play fh2 and when i select buy or my cars,it automatically restarts the console..after it restarted i select buy or my cars and everything is ok...it doesn't happen to other games.Could it be game's fault?Thanks.
Hello , helpme please , my console Xbox 360slim , have motherboard Trinity , and , my console restarting a One moment when play videogames or the console , the game locks up or rather, the screen freezes when playing, or if not as I said I reboot the xbox, but when the game is locked, the imagem is connected, the remote is turned off, and I unplug it and turn it on again, it does not turn on the remote control, and the xbox appears that if it is connected, the air that comes out of the fan is very hot, what do you think it is? and do you think that with fixing thermal paste
sthetix oh , I understand :(, well I would not know that in just 8 months I would pass this, I took care of it like a baby, if you can tell me the minimum price to fix it I would appreciate it very much, and thank you very much for answering my friend, I have already subscribed and I liked
Even tho this video is 6 yrs old, HOW THE HECK DO YOU TURN ON THE TEMPERATURE MONITORS?? I CANT FIND IT IN ANY SETTING CATEGORY AND YES ITS A 360 S/SLIM
@@sthetixofficial by the way i think my board is trinity version any solution sir? My console only opens for about half second and automatically turn off
I will try this, i got a 360 from my friend for free and it sometimes has a rrod or it works before overheating and freezing, i will update this comment if it worked Edit: so i dissasembled my 360s and i cant wven see those resistors, and now i realized i got the wrong xbox 360
The fact that this video is three years old and has corona in the title and it has a COVID 19 warning is funny
Just happened to me- even my XBOX got corona! 😔
It’s because in Spanish corona means crown but TH-cam thought it was the virus 😂😂😂
Thank you now my Xbox 360 is working properly
Do not forget to change the thermal paste under the metal cover of the processor otherwise it will not solve completely.
Yeah
Do you know what to use to put and hold the metal cover back in place after you do this?
@@MarcoS-yd9pf A pasta thermica deve segurar. Senão usa um pouco de cola thermica nos cantos depois de posicionado. Mas bem poquinho so pra ficar no lugar, pois, a pressão do dissipador vai manter ele no lugar.
@@pandainformatica8963 sorry I only speak English. Don't understand
@@MarcoS-yd9pf Nothing...the silicone used to secure it in place from factory that you cut away was only there to stop you from opening it, the new thermal paste you'll put there between the cover and the chip AND again between the cover and the heat sink (like a sandwich) will be enough to hold it in place once its all clamped down.
I've done this numerous times with XBox 360's & PS3 fat's and they've never come loose. In fact, with the adherence properties that thermal paste has I've had great difficulty lifting the covers off the heat sink by hand once they're stuck down with paste...they will never ever fall off! The key is pressure, make sure you've really pressed that heat spreader (metal cover) down onto the heat sink before putting the whole lot back on top of the chip.
Thanks so much! All I did was reheat the solder on both sides of the one resistor that was giving me a bad reading and checked the ohms. That fixed it and I didn’t have to add any solder.
Omg it worked! I just bought a broken slim with flashing red light and high fan rpm, then it would shut down. Within 20 minutes it's now fixed and booting perfectly. Thanks for the awesome tutorial!
20 minutes wow
Thank you for this, I have the Xbox360 S star wars Console and exactly this happened to mine about a year ago; powers up, 10 flashes of the red light then immediately shuts down. I was going to bin it (got a used console for 25 GBP off ebay) but forgot about it. Then came across this video, dug the console out to try this fix. However, when I tested the resistors, only one was reading high (44ohms) so I only replaced that with a solder jumper and left the others alone. It was quite difficult to do, you need a steady hand, 0.3mm solder wire, a free standing magnifying glass and a thin pointed solder iron tip heated to 300 Celsius. The console powered up and is now working fine. Not sure how long it will last, but I'm grateful for this video. Thanks again.
you r welcome
I also have the starwars 360, i feel like when i was younger i also had an issue with the disk drive
Thank you - I had solder and have done some small projects on my car, but didn't have the correct site solder or the right tip, so this comment helped tremendously
I had the same problem and only your solution solved my nightmare, thanks a lot bro you're my hero!
For what it's worth. I did this on my Xbox 360 S, and it worked. I still worry about whether I have removed the console's ability to sense future overheating, but it was a fairly easy way to bring a dead $10 console back to life.
A burnt down home ain't worth it.
@@pullingthestrings5233 the resistors on the board read 0 ohm. Using a solder jumper will also read 0 0 ohm. There is no difference between doing this fix and putting another 0 ohm resistor on the board.
Thanks. I am not a xbox tech.
I have done many things to correct.
Im sure resistors is the problem.
The fan wors.
The power cord works.
But i have reached as far as I can to solve the problem. Good instructual video.
Thank you. This solved my issue 1st time. Legend.
had a Corona v2 doing this exact issue, all of the resistor polarity was off on the board, This fixed it perfectly. To anyone worried this will cause more issues, the resistors you're removing and bridging are 0 (Yes, Zero) Ohm resistors, a solder bridge is exactly the same as replacing the resistor, just without the fail rate. as long as you can solder, this should be pretty easy for you, I did it with a soldering iron that had a melting tip, took me all of 2 mins to do the bridges and 30 seconds to flow it properly and neatly. Definitely need a new soldering iron before I tackle installing an Ace v3 though, Haha. Cheers bud, Gonna double check a corona v4 I have with the same issue and see if I can fix it :D
About two years ago I had a 360 RDOD on me and had no clue this was how to fix it. I took the motherboard to my garage today and (Edit: Solder Bridged) 2 of 6 resistors and it works like new! Tysm!
if you don’t mind, which and where did you get those resistors? i’m having the same problem and i’m not sure where i can find these specific resistors
@@mrnissan3262 Instead of using new resistors I created a solder bridge in place of them. From what I know, solder bridges work for resistors that require 0 ohm to work. I learned this from a different video, if I find that video I'll link it here. 👍
@@camrenesterdayplease link
Mine overheats quick but i had a fan in front on the fan and it works so you can buy a fan on Amazon to but on the side of xbox its call Intercooler STS
why did they put this point of failure in these at all? one of my Xbox 360 slim had this issue and I just desoldered the resistor and bridged it.
works like a charm, in fact the fan turns up less than ever before, making me think when the resistor started failing it already reported higher temps than normal.
Great job!
It's meant so that you don't burn your house down, but hey be my guest.
This totally fixed my problem! Had the red dot of death (approx. 11 red blinks) with fast fan speed at startup, would not even turn on at all. Followed this guide and all is well again! I was skeptical and am not very experienced with soldering, but pulled it off with the help of your awesome video! Also, I actually do have a trinity board (no post out board), took a chance since it was screwed anyway, and this did take of the issue for my trinity. Thanks so much for this, man- much appreciated!!
Which resistors did you remove?
@@digipimp75 its depending on what resistors are broken
wow R4D3 goes to infinte value (no working) console error 0013 turn on with a red dot and turns off in less than a minute, jumping the resistor and boot up. Thanks for the tip.
+Enfermo mares yup. U are.welcome
I've done this same method on a Halo corona unit i got and it hasn't worked strangely, about 4 of the resistors were reading in the high 20s-30s so i just removed all of them and bridged them, still a constant red light, but i could intermittently get a successful post by bridging r4d5 and r4d7 with some tweasers, several reflows didn't help either. Not sure where to go from here but its worth saving being a special halo 4 edition and the board has some software to give it the custom sounds.
I can transfer the sounds over to another board if interested
@@tonymcpherson1958 Are the sounds linked to the main board and not the front panel board? Im looking at potentially doing a board swap do you know of a guide on how to swap these over?
@@FuturizmFix sounds are on the motherboard.
@@tonymcpherson1958 ouch, was hoping I can avoid that. Is it a software job to switch these over or is it part of the hardware on the motherboard? Thanks for the help
this was the first result for "kids xbox 360 overheats and explodes"
This works for me, I really appreciate, thanks 🙏
I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
But now won't it be a problem if the console ACTUALLY overheats? These resistors aren't for absolutely nothing...
it won't be a problem. its not a resistor, but a jumper with 0 ohm
Makes me wonder if this only happens to Corona systems that have had the RGH done to them?
I think it could happen to non modded consoles too
I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
Creating the jumpers is haaaard unless you’re experienced with micro soldering.
Have just managed it, just.
so trueee bro
I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
@@josephgamer7840. Have you tried yet to reboot it after reapplying thermal compound?
@@ADT2695 i haven't changed any resistor except the Thermal paste but the console is working fine
@@josephgamer7840. Then, what is your query?
Hi and thanks for the video!
If it does not fix this problem can xbox burn? Or is this just a defect in the temperature sensor?
if it is not fixed then you cannot run the xbox
I can’t find those resistors my console is a trinity 😢
Yeah, mine too. Have you found a fix yet?
what option i must slect in the multimeter?
the diode function
@@sthetixofficial thanks a lot ;)
All I did was bridge r4d3 with a screwdriver while turning it on and it's been running just fine since.
I have a Trinity RGH , if I let it sit over night the console will stay on for about 15 mins the next time I turn it on. Then when It gives me Red dot I turn it back off and it will still give me the red dot. Does this method apply ?
+TristinHD there are so many factor.. check your console temperature, check your power supply.
Power Supply is fine, I tried multiple one still the same result . I cannot check the temp because it just gives me a Red dot BUT when I was able to get to the Dash board it said My console overheated, also the console wasnt even on that long maybe 15 mins. Replaced the Thermal paste with Artic Silver five. Still getting the red dot.
+TristinHD the resistor location is different for trinity. The solution does not apply to your console. You should check the secondary error code for your console
Okay how would I go about checking my secondary error Code ?
+TristinHD xbox-experts.com/tutorial/secondary-error-code/
Thanks for the tip. Had one of these reading 70ohm and the others OK, but accidentally knocked off another resistor while removing the bad one. Couldn't get a solder ball to flow between the pads so had to cut some small strips of copper from a stranded 12ga copper wire and tin them on my iron, then peel off the iron using tweezers and place with the tweezers while heating.
I have a feeling this would have been easier with some replacement 0ohm resistors but didn't have any on hand.
so have u fixed it?
@@sthetixofficial yeah I wanted to get it together and test to be sure. Working well now so this was definitely the fake overheat.
Was confusing because this system had bad thermal paste application under the heatspreader and originally changing that got it working but it stopped shortly.
Be sure to remove the corona on the Xbox.
Did this tip and worked, but 3 days later, it turn on but 5min later it shut down on overheat, but its only a litle warm, Any ideas?
replace ur thermal paste and maybe u have bad solder connection
you said remove the jumper wire but in the "it should look more or less like this" photo you have the jumper wire attached. do you reconnect it?
Yes jump it using solder
Hey sthetix. Great & clear video, just got fixed GPU false temperature. 10* and regards
ur welcome
How do I check my Xbox CPU temperature like in the videobecause it keeps saying that my cpu is hot but I have the fan running at 12 v
do the guide..
Oh thank brain fart
So I have this issue but I have never used a multimeter before and would like some help on what setting it needs to be on to test the resistors
if the resistance is not 0 or more than zero, you need to replace or jump that resistor
@@sthetixofficial thank you very much for the video and the reply I appreciate the help people like yourself give out on TH-cam 🙂
you are welcome
@@sthetixofficial I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
I have the same problem but i hear no fan spinning 😕
try replacing the fan.
interesting, super complex but would be improved to also replace the fan over 2000 RPM or dust clean the fan overall with replacing thermal paste that uses for PC?
replacing fan won't do anything. its a sensor malfunction due to bad jumper
Could someone list off the tools needed for this please.
soldering iron
just picked up an xbox 360 slim with the 11 flashing red dot + full speed fans issue. One of those resistors was 1.5 Mohms, blew them all away and replaced with solder bridges. The Xbox is back from the dead.
I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
So basically just solder balls?
Is there any downside to doing this vs buying resistors and replacing them? and if you were to replace them where would you buy them from?
no.. just jump it
thank you..is this all sickness of xbox 360 corona motherboard?
ya
@@sthetixofficial one more thing..do you need a heat gun to form the solder bridge?. coz i dont have it..thank you for your videos
no need
Yeah it was sooo easy it took a little while to learn what soldering was or what a Flux was but in 8 minutes I had a working xbox again 😀
Como lo hiciste?
what exactly did you to remove the resistors? and you use something more common?
+anthony Goespewpew that resistors have 0 ohm so just short it together
sthetix thanks a lot!
thanks. It worked and issue resolved
I have this problem on the Xbox 360 e slim, it shuts down and restarts with the fan on high speed then restarts again and runs fine. From startup it says lack of ventilation and over heating and goes though what I said every time. Is there a fix?
+retrostansolo check its resistor
Does every console get these loud fan blinking red dot problems on the slims or just some?
mostly on coronas
sthetix are the Coronas the layer date systems cause I have a Star Wars Xbox 360 from late 2011 that’s still runs today just looking out
star wars is coronas
sthetix I have a Star Wars corana version till this day playing actual right now mw2. But I’m worried cause I don’t think it’s specific cause 6-7 years later hear it is. Dunno I had a 2010 glossy version which has the RDOD no fan speed up just plain red dot of death with normal fan so. 2011 my Star Wars version right now is actually online trying to combat these hos
I don’t have all this equipment and don’t have the money for it is there an easier way ?
no
If you look around you can find Chinese combo stations that are 700+ watts and they are good enough especially if you buy some better tips. $130 might sound like a lot but you'll be able to fix a lot of things.
My Xbox 360 s (RGH) has Memory overheating problem, the temperature reaches about 84 celcius degrees, and after some time (30 min) turns off. Solutions?
yes try this guide.
The temperature dropped after the new paste was applied
good
Can you just simply remove the resistors to fix the issue or do you HAVE to create a solder jumper?
u need to create a solder jumper
My xbox doesn't seem to have a row of resistors like that, should I check the same resistors on my xbox 360 slim
its for corona version.. not for trinity
@@sthetixofficial ok, thank you
I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
just bridge the resistor
I checked my resistors with a multimeter, but they are all fine. All come up either 0 ohm or .08 ohm. Mine blinks red 10 times before shutting off
try to jump it all
@@sthetixofficial its still giving me the red ring 10 times
Tried it a few times, might have had some kind of bridging, but this worked. Thanks!
Hi, i have this problem whit the case temperature, how i fix it?
+Javier Aguilar case temp? Put it on the open air and try again
same problem only false case temperature what i do ?
corona?
@@sthetixofficial trinity please help me
@@sthetixofficial I got a Corona it's brand new it's never been used it was bought and ever since been in the box I cranked the damn thing up and it runs hot I mean there's no flashing lights or anything like that the lights green but it just immediately started blowing real hot ass are right out of the top vent. It's just hot immediately after I turn it on is that normal. Doesn't seem to get any hotter but damn it's hot right off the bat. It's got maybe forty-five minutes on it total since it was bought out of the box. Thanks for any help
perfecto muchas gracias, me funciono de maravilla
im having a same problem.. can you help me where do i repair my unit here in dubai?! because im scared that maybe they dont know how to fix it properly. thanks..
I don't know.. sorry
Thanks for the video. I can solve my problem with the red dot button in my xbox 360 s . Removing and linking the resistor like the video. 😀
great
Is it safe to remove these resistors? Shouldnt you just replace the broken ones instead?
remove and jump it
@@sthetixofficial i know u've jumped them, but they were put there for a reason maybe removing them put the xbox in danger later, would it be better to replace the ones that give high ohms? I sent mine for repairs, he fixed red light but cpu temp starts at 75c, he said he replaced a resistor, i m wondering if i should ask him to jump the resistor he replaced or ask him to jump all resistors. Thanks
its a 0 ohm resistor, its the same as to jump it..
Hi, ive got a strange problem cuz when i boot up my xbox 360 slim then normal green light shows up everything is cool but the fan is speeding like +10% in 30sec then it gets so loud and xbox just shuts of. I mean when i boot up the xbox, fan is getting louder and louder and then xbox shuts off, i dont have a red/blinking light just green like always, it shutdowns within like 4-5 minutes
use this guide
My Xbox motherboard does not look like this I can’t find the specific resistors and it looks a lot different is there somehow I have a different version?
its for corona only
Can i just remove the bad resistors and leave it? Without creating jumpers?
@@sthetixofficial And this should help in case of Winchester motherboard?
if u solder jump the resistor it should be near 0 ohm after right? because mine before solder jump 75 temp now its 65. but i forgot to check it. because i dont own a multimeter.
its 0 ohm after u jump it
lol you say corona and it shows "want to learn facts about covid-19"
My Xbox doesn’t have a post out next to the cpu where is it
Can you jump one? Or do you have to jump them all?
jump them all
sthetix ok, cause only one of mine are reading high and just wanted to make sure. Cause I have the rdod with high fan, so this should hopefully fix it.
y para las trinity son las mismas resistencias a revisar ?
the console is flashed with rgh and lt3.0, turn on and enter the frestyle menu and throw me that error
*Please reply*
Is the xbox 360 slim fan shroud important?
+Randomthingz2show Randomthingz2show not important
sthetix if i take that off,will there be more airflow or less?
+Randomthingz2show Randomthingz2show it doesnt affect any airflow logically
thanks for the vid, did everything u did but now the system powers up, fan spins at full speed for like five secs and then spins down. any idea what this could be?
maybe u didn't solder it correctly?
Mine did this too. I didn't try this repair though.
Do you resolder the red post wire when your done
red post?
Sorry red wire off post 1
My slim works for about maybe a hour but after awhile it just turns off and the box it plugs into light just goes red do you know how to fix it
try replacing the power supply
@@sthetixofficial My friend bought an Xbox Slim overseas with 120v power supply. Is it okay to use it on 240v outlet? My country uses 220-240v output on all electronics.
of course not
So I leave the post-out wire off ??
it is not related to the jumper , right?
maybe ill try that! I have an xbox 360 slim right here, right after i start it it shows an red ring and the fans spin at abt. 100% (almost louder than an airplane (jk)) and then it shuts off... At least i think so, didnt look on it for quite some time now...
can i make it without flux?
better use flux
@@sthetixofficiali found that resistors dont wanna melt without flux, i dont have flux now can i use something else?
use flux only
@@pioterzapaa3118 Resin is a common alternative to flux, but you should be able to get soldering flux at the nearest store in the hardware isle
Is their any way to avoid this problem or will it happen to all xbox360coronas I'm just concerned cuz this seems to be happening to a lot consoles and I am not very experienced with soldering
it happens randomly after some time
@@sthetixofficial update the R4D4 resistor went bad and gave error 0013 but I fixed it thanks
changed the one that showed 30ohms, it worked
I have same issue but my thermal paste is changed recently ...so i need to remove resistor or i can use just like that.... Please reply
@@josephgamer7840 if you don't have the resistor you need to make a bridge with solder
@@LenoxFilms but it's very important ? , till now it's working fine , can play just like that or need to change it definitely ?
@@josephgamer7840 it wont boot man, of course it is lol
@@LenoxFilms actually my prblm is console is working perfectly but when i check temperature it's showing faulse but the console is working fine i can play all the games ....and do u understood what I'm trying to say
Hi mate, thaks for video. I have the same problem (0012) with trinity motherboard. Any solutions for it?
Hmm no clue for that
Hi!I have a weird problem actually.So when i start to play fh2 and when i select buy or my cars,it automatically restarts the console..after it restarted i select buy or my cars and everything is ok...it doesn't happen to other games.Could it be game's fault?Thanks.
game fault or hdd fault
sthetix Oh..when i delete the game,all the saves are gone too?I've never had an XBOX 360 before so that's why im asking..
no it wont
Hello , helpme please , my console Xbox 360slim , have motherboard Trinity , and , my console restarting a One moment when play videogames or the console ,
the game locks up or rather, the screen freezes when playing, or if not as I said I reboot the xbox, but when the game is locked, the imagem is connected, the remote is turned off, and I unplug it and turn it on again, it does not turn on the remote control, and the xbox appears that if it is connected, the air that comes out of the fan is very hot, what do you think it is? and do you think that with fixing thermal paste
Gpu is dying.
sthetix really ? and there is not a way that can last longer? or to fix it? :( a reballing, or so?
No..u must replace the gpu
sthetix oh , I understand :(, well I would not know that in just 8 months I would pass this, I took care of it like a baby, if you can tell me the minimum price to fix it I would appreciate it very much, and thank you very much for answering my friend, I have already subscribed and I liked
Here i usually charge it for $150.
hi sir, I have a Xbox 360 Slim 0013, the above methods can repair my Xbox?
I have a problem with a rgh corona the cpu shows a temperature of 1.0 can you help me please
so low temperature?
Yes i dont know whats wrong with the xbox, when i turn the console on only last a few minutes and then red light
How to fix it?! Its still red
+abin hero not all red error has the same solution
Ventilation problem? How to fix it?
+abin hero maybe u need to replace the thermalpaste
Even tho this video is 6 yrs old, HOW THE HECK DO YOU TURN ON THE TEMPERATURE MONITORS??
I CANT FIND IT IN ANY SETTING CATEGORY
AND YES ITS A 360 S/SLIM
you need to hack it first bro
@@sthetixofficial how do you hack it then?
Also in case you ever want to, Can you remove it?
Thank you, I just had to short R4D3 to revive the dead XBOX.
good
Thank you x 10 it worked qbd in grateful
i have same mother board plz tel me whats the avg temperature while playing games mine going at 82c its normal or not
not normal
@@sthetixofficial what i do change tharmal paste of inside sheild ish ??
it doesnt do much
@@sthetixofficial what i do bro
slim corona?
I don't have a fan fan so I used some of my games and the cases and fanned it while it turned on and it work
Plz help my board only got r4d4 and r4d5 . . Its only open the fan for about half sec and turn off . . Plz help me what to do
fan? what fan do u mean?
Exhaust fan sir
@@sthetixofficial from the heat sink
@@sthetixofficial mine only got r4d4 and r4d5 . .
Not like in ur video r4d3 to r4d8
@@sthetixofficial by the way i think my board is trinity version any solution sir? My console only opens for about half second and automatically turn off
Hi how do you get the temperatures to show on xbox
u need to install cfw and run freestyle or aurora
Really who has those tools bruh
this could fix a 0011 error on a corona board??
no
thanks for respond, another question. Do you know the reason that casues this error?
usually gpu dies
well, I think that my console needs reflux or reballing... bad luck... thanks so much for respond!!! you earn a susbcriber!!
u r welcome
I do same in trinity its not booting anymore plz help
it's not for trinity
@@sthetixofficial plz tell me what is the solution of trinity quick heatup shut off i have 2nd xbox trinity which have shutoff problem
i don't know about trinity
My aunt has a peoblem. She sqid that her XBOX 360 deleted its own games. When they downloaded new ones all games are not loading properly.
When it was gonna play games
xbox would never delete those games by itself.
@@sthetixofficial maybe the memory was full
what is that background music?
is it written in the description?
me han salvado la vida , de verdad
the xbox 360 console is shutting down to protect the console from insufficient ventilation
different solution for trinity. maybe u need to change the thermalpaste
I have almost same problem but with Edram 82*C while cpu is 55 and gpu is 46. I think Edram has problem
Help me please
do the same thing in the video
Can I replace new resister instead jumping?
jump it
I will try this, i got a 360 from my friend for free and it sometimes has a rrod or it works before overheating and freezing, i will update this comment if it worked
Edit: so i dissasembled my 360s and i cant wven see those resistors, and now i realized i got the wrong xbox 360
is it the same on xbox fat
no
If i didn't fix it what's going?
then your console could have another issue.
Music is too loud and annoying!
+Darren Bee sorry for that
sthetix thank you for saying. I just couldn't watch your vid as I couldn't hear you over the music. I have a hearing issue which doesn't help either.
+Darren Bee its an old video..i have corrected the speech and music for all my newer videos.
Thank you
Thanks!!!!
Do u have to resoder them
yes
@@sthetixofficial I tried it dident work