What you should of done was construct electrical leads on each corner. That way you would reduced the electrical resistance of corrosion resistance metal plates. This would increase efficiency and reduce the heat in the HHO generator Sir. Hope you keep that in mind when you build another unit of want to upgrade what you made by modifying just a few plates. Also, you need to tweak the car system electronics to take advantage of the OxyHydrogen gas. JOB well done DIYer. v
Прошу, брат, дайте мне ссылку на видео с вашими подробными указаниями на повышение эффективности. Это важно всем людям, пока доступен широкий инфообмен
If you look at the short term fuel trim through the OBD 2 you should see a drop as the ECU changes the injector pulse width, this way you can keep the ECU in the system and avoid a lean burn condition which is not good at high RPM. Also to mitigate intake explosion by fitting a flap valve after the Throttle body to release excess pressure from the intake plenum. I had Lexus LS400 V8 on LPG / Oxygas. Good effort.
Had received a few suggestions. Hope it helps 1. Use a powerful flashback arrestors- preferably 2 one near the hho kit after the bubbler and 2nd near the air in-take. 2. HHO input after the MAF(Mass air flow) sensor and not before. p.s. these are just some suggestion that - do it on your own risk
@@IamAli89 A flashback arrestor in an HHO cell is a safety device that prevents backfires and flashbacks when extracting gas. It's used to protect the equipment and user from damage or explosions.
Voltage should be around 1.7 VDC per cell, target amperage should be .25 amps per square inch per cell. Use cross hatch pattern. HHO implodes during ignition. Water fog injection is needed to emulate slower burning fuel such as gasoline.
Incorrect! The reason the graphite cell was shedding was because he used way to many volts with the Urea electrolyte. It only needs 0.3v per neuteral cell! He could have had 18 cells with only 5.5V.
If the HHO is fed into the intake BEFORE the airflow meter; the flow meter is metering out fuel for a gas mixture that already contains fuel (H2). Feed your HHO into the system AFTER the airflow meter just for a start. There are other changed engine parameters that need to be tuned for too.
The map and maf sensors have to stay in a proper parameter. Instead of going through different resistors to find that one for your car just put on a large resistor with a potentiometer on it and adjust the potentiometer until it works the parameters your need. That's the solution.
@@shaneoneill2254 The map and maf sensors have to stay in a proper parameter. Instead of going through different resistors to find that one for your car just put on a large resistor with a potentiometer on it and adjust the potentiometer until it works the parameters of your need. That's the solution.
The problem was not the graphite plates, but the electrical contact was not insulated. Check the resistance from the wire and the graphite plates. Graphite is actually far more efficient than stainless steel.
Did you add an efie, ? Otherwise the ecu detects more o2 and starts to compensate adding more fuel. I disconnected the fuel system and add a SU carby, the ecu only controls the spark and timing. I run a very lean fuel mix and add 180 watts of hho at 15 amps giving me 10 liter per 100 on a 3 liter pajero that used to do 15 liters per 100ks.
I liked your experiment. I am planning to build one for my bike {350 cc carburetor bike}. I understand that graphite has a smaller lifespan to SS304. So I made my plates with 316L which is more anti- corrosion. I was thinking in the same lines as not to overload the alternator and considering a separate power supply. I intend to publish the results on my channel when I get to where you are presently. I was also thinking to install a wind and solar generator to charge the additional battery on my bike. One factor which I would like to consider is de-carbonization of the engine(while using HHO) over a time period which may result in better efficiency. Instead of HHO. What performance one can get of ICE if it pure hydrogen? This is my unanswered question so far. All said and done I respect you for the time and energy to make the video and sharing. Thank you. Bless you
for max efficiency try to get the voltage per cell down a lot. for example experiment with H2SO4 (battery acid ... yes ...) with this, the cell voltage goes down to about 1.3V per cell. also use verry thin plates since a thicker plate heats up more due to electrical resistance. now you'd think battery acid is too dangerous right? well, so is KoH, its just on the other side of the PH neutral.... also, you only need verry little of it, basically you set the max amps with the amount of acid. you can obviously use extra acid, but than you have to set max amps with the controller. also, like @rexford9019 said, limit amps to 0.25A per sqr inch. means larger plates ;) --> better efficiency
Este video nos anima a seguir haciendo lo que la mayoria de las empresas se niegan a reconocer. Felicitaciones por el video, seguramente seguiras desarrollamdo este sistema, y estaria bueno injectarlo directamente. Habra que reprogramar la computadora y agregar un compresor a diafragma para que sea capaz de generar 3,5 bares. Asi se puede usar el injector del auto y evitar explosiones.
I use stainless steel light switch covers. I do 12vd to every plate . I've been doing it 8 years. No heating problem yet. The amperage is what heats the water.
@@WayneLambrightIII clean them with alcohol after touching them. You will be surprised at how much oils from your touch reduces production and mount them vertical not flat for the best production. I'm getting ready to experiment with a old style vehicle distributor coil. 30k volts and adjusting the solution and different wiring configuration.
Me gustaría ver este sistema en español tipo Argentino.y hacerlo más despacio para poder entenderlo bien. Porque ya tiene bastante electrónica de esa forma podemos sacar un modelo para aplicar a nuestro auto algo entendí hacerlo pasar.por los inyectores estaría muy bueno estaría más protegido de fugas y explosiones alguno de ustedes buscando y buscando lo va a Acer funcionar yo he hecho varios proyectos pero me falta capacidad de electrónica mostravsn una placa que iba a un potenciometro le daba más corriente o menos sigan buscando todos que lo tenemos que sacar felicidades para todos
-O SISTEMA de hidrogenio é muito bom em baixas rotações ,em alta não consegue manter o fluxo ,então se voce não tiver pressa vai ter uma boa economia. parabens obrigado pelo video !!!
You can’t use the built in consumption measuring, it does not measure the consumption of the fuel consumed by the engine, it does calculate an approximate consumption according engine parameters.
🤫 Perforated metal sheet has a larger surface area, also if your gas can't get away from anode/cathode fast enough you're generation efficiency goes down as you're using less or the available surface area. The water heats up because stainless steel is very resistive, platinum is the perfect material to use but it's too damn expensive. Low voltage, high amps is apparently the way to go or high voltage low amps pulsed at quite low frequency to keep temperatures down. I wonder how well 240v at 50hz rectified would perform? With graphite plates the problem is that it's very sacrificial, no good as you seen, not for anode anyhow. We need to use an anode that can't be used for electroplating yet is very conductive and does not erode or corrode. If you think of a cost effective material that fits requirements please let me know 😊👍
Yeah the graphite experiment is quite interesting, I wondered why they're not connected too in such a small build.... I actually used a neutral plate every 3 stainless plates in my builds.
Tests should be conducted on vehicles with 5th generation GNV systems. As they already have more advanced equipment that allows changes in the systems and can better accept HHO. As an admirer of the HHO system here in Brazil, I am interested in learning more about its applications and benefits.
put a positive wire onto a tap with water, so that when the water drops out it carries a positive charge. then put your negative terminal onto some aluminium wire (like used for welding) when the positive water meets the negative aluminium, they should flash into 100% HHO, the byproduct will be aluminium oxide, which you can reuse again by smelting it back into aluminium.
11 หลายเดือนก่อน +3
Eu também tenho muito interesse nesse sistema, desejo troca de informações. I am also very interested in this system, I want to exchange information.
Has anybody added hydrogen to a diesel engine? I'm afraid to try because of pre ignition. Yet just mentioning this, I can buy a one cylinder motor for $150 bucks I should test on this. Stanly myer was mixing exhaust gas with the intake to slow the pre ignition time down, just an fyi.
Great, very informative experience except that oxy hydrogen (HHO) is dangerously explosive if the detonation is too strong!!! it is better to complete the assembly with a separation system to obtain the hydrogen AND the oxygen each on their own
@@CoincidenceTheorist Try to scare people!!! No, but am I dreaming or what? I'm just informing these people of a scientific truth that everyone should know It's YOU who SHOULD normally warn them and you don't do it, you mislead them!!! and it’s serious! Try doing this experiment on a small scale to convince them: Don't forget that I am here because I choose to be
If you want to separate hydrogen and oxygen you can do it with a powerful magnet or electromagnetic as they are opposite magnetic polarity... That's what I came to say but the health and safety guru distracted my attention 🤣🤣👍
Use Platinum plated strips. Just 2 is all you need, extremely efficient and high production. Still, the H must be stored in tanks, compressed and regulated out that way.
Works for short time before you melt your piston rings, burn your valves then your car looks like a diesel... if you are going to run hotter gas you need to set the engine up for hotter burn.. then it works
Uh? Just add more water? Unless it is chemically altered in the process it is catalytic. I cant see anything harmful coming out, but maybe not pour it into a watercourse
Can we use this project for cooking purpose ? what the upgrade thing to use this gas for cooking purpose ?? If i use 12 volt 220 amp then can we produce much gas for cooking purpose ??
Great build video. I am working on something very similar. Is there anyway for you to estimate how much gasoline was needed to replace the charge on the battery?
i can't compute it when it comes from the engine.. i don't have intentions to charge it from the alternator, instead it is solar or grid. it makes it cheaper that way
for a correct calculation of consumption you must also enter the parameters for the electricity you use, I don't think you have an 800W alternator in your car so the energy stored in your battery at the end of the test will be less. After all, the gas mixture you add is one of the most powerful fuels, so at the end of the your test in one case you only use petrol in the other one petrol add the detonating mixture H plus O. Having said this, I do not exclude the possibility that the system could provide greater returns.
Jika 3 liter per menit dan pakai susunan plat paling efisien yaitu -nnnnn+nnnnn- di jarak antar play 0,5-0,8 milimeter itu pun perlu setidaknya 600 watt sebab di kondisi paling efisien pun cuma 0,1 liter per menit gas HHO tiap 20 watt. Jika 3 liter per menit accu dan alternator tidak akan cukup untuk memberi supply daya. Kalau andaikata kurang efisien perlu 850 watt maka hasil gas dengan susunan plat seperti di video mustahil 3 liter per menit, separuh sudah bagus sekali. Perlu accu yg di charge. Maka bukan mobil ternaga bensin saja tetapi, mobil tenaga bensin + accu. Pengujian jangka pendek bagus cuma apa menguntungkan jika dipakai jangka panjang?
take a look at the amps, if You put an additional batteries for HHO this could give You something. But in general You will have a hybrid car, petrol-electrical.
flash positive charged water over a negatively charged aluminum wire. when they meet, they should create 100% hho with aluminium oxide as a byproduct, which can be heated back into aluminium.
So ad a separate alternator? Room to make the amps. Where does this equals on price to drive. And what will happen to the battery. Still efficient. I will still say yes
The physicist in me cannot agree that another alternator is the answer. Many sensible suggestions about fooling the oxygen sensors on modern vehicles As a chemist I don't understand why the urea or sugar has any effect (I would try washing up liquid to reduce bubble size and surface tension. I strongly advise more plates and lower voltage with higher amps to avoid waste heat But good effort on the road test - after all that will convince others to have a go
I spent 3 years doing all kinds of experiments with hho, I even used Peltier tablets to cool the water, the Idea to know the consumption and use the scanner to know the injection time.
Bro, nice build, awesome. Your car adjusts fuel and air to idle at as set number rpm. It was going up with hho but was then adjusting fuel to lower speed to hit target. Same when you removed hho and it went down then back up to target. Is that what you mean by 'automatically adjusts idle rmp depending on environment'?
as you state the pressure gets too high over 850. Although you have the setup for better containment already. that case for one! you just need to get some metal containers of somekind for the other parts that hold the electrolite?
the current is controlled by how much electrolyte you put into the mix, more electrolyte = more current. as the solution warms up it becomes more conductive and can run away on you. one way to help controlling heat is by useing six cells in series just like a car battery.
faz uma celula que produza os gases separados e coloque no carro que funciona sem o combustivel do tanque. O Hidrogenio coloque um kit controlador de gas GLP e o oxigenio despreza, o tbi do carro que fará a dosagem.
Consider In day light, put some solar panels on your car and skip your voltage generator, use the sun to make the electricity and just see how you do with MPG.
do you plan to carry out the experiment with HHO?? If you have the possibility I suggest you also test the separator system and share your thoughts with us Thank you so much
планируете ли вы провести эксперимент с HHO?? Если у вас есть возможность, я предлагаю вам также протестировать систему сепаратора и поделиться с нами своими мыслями. Большое спасибо (Я не знаю, возможен ли автоматический перевод!!!)
After just a few minutes, such a cell boils and the insulation that needs to be used is PTFE. another disadvantage is that stainless steel plates corrode and the electrolyte turns into green soup. For many years I have had contact with devices from OWELD, which produces such devices intended as gas welding machines. a better solution for a car is an oxygen cylinder with a volume of 5 liters and a tube leading to the air intake. The engine has a great kick. You have to be careful not to overheat the pistons.
In my opinion, generation of HHO makes only sense, if you have excess solar energy and want to have a fuel storage other than batteries. With 1 liter/min which I can get from a single panel, I get all energy I need for home usage. Due to its explosive nature of HHO, I would only store hydrogen in large containers, and sell the oxygen. For separation of the gasses, it needs a different build, though.
I Just though of something really interesting! What if you installed that potentiometer on the gas pedal somehow so that when you press it down the voltage will increase so you can possably get even better milge so the Oxyhydrogen is more abundant when accelorating? would be even better if there was some sort of storage tank and pressure gauge with some regulators etc. is this something that could make tis even better? or too much?
hydrogen production by increasing voltage (not preferred) but current is. the impact of increasing current takes a few seconds to produce more Hydrogen, may not align with throttle response, just thinking not done it yet to tell you for sue
I am literally scared of HHO, but this is a good video. I mean, hydrogen is explosive enough with air, less than 30 percent of oxygen. Even if you do not mix it perfectly.
Hi interesting video, did you see fluid level drop down on start up = half you plate area non productive ... To gain best plate coverage connect you're possative cable to upper / top of plate , current heads down plate looking for ground..... Connecting you're negative to the bottom of plate block so current heads on up... Plate block.... Fit a fuse. Look for better bubbler and bottles so you can fit safer If you cut corners off left for possatve connection... Right for negative side connection... Keeps them seperate, less chance of shorting out ...
@@albertnario4877thanks for your honesty! Since you are putting some additional load ( via the alternator) on your engine in order to produce the HHO on board, even neutral power or/and fuel economy “gain” means , that HHO is helping at least a little bit with improvement of combustion .
The battery for the HHO is separated from the engine.. it has its own energy provider.. it is cheaper to charge the battery than to use fuel.. sorry for the poor explanation on that.
the big problem of that design is HEAT and low conversion of liquid into gas. i suggest that you study or find the right resonance frequency of water; ;if you found it you can now easily separate the hydrogen and oxygen very fast with 12volt and 3amp power supply only without additives'..and your reactor metal mush be like in a catalytic converter. hope this will help to your experiment
That entire system would melt inside of 10-15 minutes. That thing is going to get so hot that it will explode. Plus, even if it were designed well, it would still be a huge net energy loss in a car.
He lost me when I saw him put complete seals around the outer parameters of each plate. I mean I know little about this. But isn't it supposed to be more free flowing around the plates than that?
Your plate sanding wasn't done right , that is done in a cross stich pattern by sanding diag top corner to bottom corner of the plate then do again corner top accross to bottom corner like an X pattern getting everything fully sanded both sides it makes a huge differance. Also port it in were the vacum on the brake master clinder connects faster delivery . Good Job well done
You need work the correct amount of water. When the acid level is at its peak. No more gas is made. Dont ask way. I dont know. You need keep a clean but very small amount of water running in the tank. Hope it helps mick Australia 🇦🇺
also this is NOT a "Hydrogen" generator this is simply this generates a hydrogen and oxygen mix by electrolysis which is very inefficient (this is why it is NOT used to generate Hydrogen gas for cars or anything). This gas mix is highly combustible more than you will be able to handle in an engine bay and wondering how you would introduce this into the engine without blowing it up. 10% fuel economy just not possible counting everything you won't believe me anyways so not trying to give you the math ... .But why not just show the power used for this 3L .... in Watts or Joules then we can calculate how much "charge" Watt/h or you need to carry in your car as charged battery ... and maybe you can convince yourself that this is sorcery...
except the the energy expended on the electrolysis exceeds the energy that can be harnesses from the HHO. So would would be better off just putting the battery in the car & running an electric motor assist. Oh wait, somebody already did that...... 🙄
tutto bello...e ben fatto peccato il discorso sul risparmio di carburante che non può essere vero. PErchè produrre l'idrogeno dalla batteria costa sicuramente più energia di quella che ne ricavi. E questo lo dice il primo principio della termodinamica. In ogni caso hai fatto un bel generatore di idrogeno.
What you should of done was construct electrical leads on each corner. That way you would reduced the electrical resistance of corrosion resistance metal plates. This would increase efficiency and reduce the heat in the HHO generator Sir. Hope you keep that in mind when you build another unit of want to upgrade what you made by modifying just a few plates.
Also, you need to tweak the car system electronics to take advantage of the OxyHydrogen gas.
JOB well done DIYer. v
thanks, i do that..
@@albertnario4877 HOPE this helps you with your DIY experiment Sir. Peace and out v
Прошу, брат, дайте мне ссылку на видео с вашими подробными указаниями на повышение эффективности.
Это важно всем людям, пока доступен широкий инфообмен
If you look at the short term fuel trim through the OBD 2 you should see a drop as the ECU changes the injector pulse width, this way you can keep the ECU in the system and avoid a lean burn condition which is not good at high RPM. Also to mitigate intake explosion by fitting a flap valve after the Throttle body to release excess pressure from the intake plenum. I had Lexus LS400 V8 on LPG / Oxygas. Good effort.
Can you tell me more about your lexus LP setup? I want to do the same to my vq25 engine.
OK
Had received a few suggestions. Hope it helps
1. Use a powerful flashback arrestors- preferably 2 one near the hho kit after the bubbler and 2nd near the air in-take.
2. HHO input after the MAF(Mass air flow) sensor and not before.
p.s. these are just some suggestion that - do it on your own risk
yes, thanks 👍
@@albertnario4877 you have to bypass intake sensor or else computer detects it as to lean or too rich as a result you waste gas
What do you mean by flashback arrestors? Bubblers or something else?
@@IamAli89 A flashback arrestor in an HHO cell is a safety device that prevents backfires and flashbacks when extracting gas. It's used to protect the equipment and user from damage or explosions.
@@IamAli89 anti-flash-back !!! ( like a oxy-cutting gaz )
Voltage should be around 1.7 VDC per cell, target amperage should be .25 amps per square inch per cell. Use cross hatch pattern. HHO implodes during ignition. Water fog injection is needed to emulate slower burning fuel such as gasoline.
2Н2О >>>2 Н2 +О2 !!!!!!! 😅😅😅😅😅😅😅ННО 😅😅😅😅😅😅😅😅😅😅😅😅
2H2O =HHO + HHO
Incorrect! The reason the graphite cell was shedding was because he used way to many volts with the Urea electrolyte. It only needs 0.3v per neuteral cell! He could have had 18 cells with only 5.5V.
Agree 👍
A trick to slow the burn rate of HHO is by bubbling it through any hydrocarbon fuel, where it picks up a few atoms and slows down the burn!
If the HHO is fed into the intake BEFORE the airflow meter; the flow meter is metering out fuel for a gas mixture that already contains fuel (H2).
Feed your HHO into the system AFTER the airflow meter just for a start. There are other changed engine parameters that need to be tuned for too.
Correct.....same with oxygen sensors. Put spacers/extension between exhaust pipe and ox sensor.
Why
What kind of spacers. For length
The map and maf sensors have to stay in a proper parameter. Instead of going through different resistors to find that one for your car just put on a large resistor with a potentiometer on it and adjust the potentiometer until it works the parameters your need. That's the solution.
@@shaneoneill2254
The map and maf sensors have to stay in a proper parameter. Instead of going through different resistors to find that one for your car just put on a large resistor with a potentiometer on it and adjust the potentiometer until it works the parameters of your need. That's the solution.
The problem was not the graphite plates, but the electrical contact was not insulated. Check the resistance from the wire and the graphite plates. Graphite is actually far more efficient than stainless steel.
Did you add an efie, ? Otherwise the ecu detects more o2 and starts to compensate adding more fuel. I disconnected the fuel system and add a SU carby, the ecu only controls the spark and timing. I run a very lean fuel mix and add 180 watts of hho at 15 amps giving me 10 liter per 100 on a 3 liter pajero that used to do 15 liters per 100ks.
what is a SU carby?
This is all Swedish to me.
can u explain what you mean when you say u disconnected the fuel system and added a SU carby
I liked your experiment. I am planning to build one for my bike {350 cc carburetor bike}. I understand that graphite has a smaller lifespan to SS304. So I made my plates with 316L which is more anti- corrosion. I was thinking in the same lines as not to overload the alternator and considering a separate power supply. I intend to publish the results on my channel when I get to where you are presently. I was also thinking to install a wind and solar generator to charge the additional battery on my bike. One factor which I would like to consider is de-carbonization of the engine(while using HHO) over a time period which may result in better efficiency. Instead of HHO. What performance one can get of ICE if it pure hydrogen? This is my unanswered question so far. All said and done I respect you for the time and energy to make the video and sharing. Thank you. Bless you
😊
Hi SS317 Has a much lower sulphur content than 304 or 316. the plates will last longer and minimal sulphuric acid gas into the engine.
for max efficiency try to get the voltage per cell down a lot.
for example experiment with H2SO4 (battery acid ... yes ...)
with this, the cell voltage goes down to about 1.3V per cell.
also use verry thin plates since a thicker plate heats up more due to electrical resistance.
now you'd think battery acid is too dangerous right? well, so is KoH, its just on the other side of the PH neutral....
also, you only need verry little of it, basically you set the max amps with the amount of acid.
you can obviously use extra acid, but than you have to set max amps with the controller.
also, like @rexford9019 said, limit amps to 0.25A per sqr inch.
means larger plates ;) --> better efficiency
But the battery acid is more corrosive, I guess?
What can be an ideal length, width & grade of SS plates? Pls answer in inches, thanks
Este video nos anima a seguir haciendo lo que la mayoria de las empresas se niegan a reconocer. Felicitaciones por el video, seguramente seguiras desarrollamdo este sistema, y estaria bueno injectarlo directamente. Habra que reprogramar la computadora y agregar un compresor a diafragma para que sea capaz de generar 3,5 bares. Asi se puede usar el injector del auto y evitar explosiones.
Where should i set the pipe from where HHO gas is prodcuing to get the best outcome of the HH? Air filter box or something other?
I use stainless steel light switch covers. I do 12vd to every plate . I've been doing it 8 years. No heating problem yet. The amperage is what heats the water.
Very nice idea. I see I can get one for $2.75 usd. Already have holes in them No drilling. Wonderful.
@@WayneLambrightIII clean them with alcohol after touching them. You will be surprised at how much oils from your touch reduces production and mount them vertical not flat for the best production. I'm getting ready to experiment with a old style vehicle distributor coil. 30k volts and adjusting the solution and different wiring configuration.
Hello from Colorado. Excellent work!
thanks sir
Me gustaría ver este sistema en español tipo Argentino.y hacerlo más despacio para poder entenderlo bien. Porque ya tiene bastante electrónica de esa forma podemos sacar un modelo para aplicar a nuestro auto algo entendí hacerlo pasar.por los inyectores estaría muy bueno estaría más protegido de fugas y explosiones alguno de ustedes buscando y buscando lo va a Acer funcionar yo he hecho varios proyectos pero me falta capacidad de electrónica mostravsn una placa que iba a un potenciometro le daba más corriente o menos sigan buscando todos que lo tenemos que sacar felicidades para todos
-O SISTEMA de hidrogenio é muito bom em baixas rotações ,em alta não consegue manter o fluxo ,então se voce não tiver pressa vai ter uma boa economia. parabens obrigado pelo video !!!
2.6 volts is more efficient you need to add neutral plates to divide into cells to get to 2.6v from 12v.
would you please explain why urea is needed?
You can’t use the built in consumption measuring, it does not measure the consumption of the fuel consumed by the engine, it does calculate an approximate consumption according engine parameters.
🤫 Perforated metal sheet has a larger surface area, also if your gas can't get away from anode/cathode fast enough you're generation efficiency goes down as you're using less or the available surface area.
The water heats up because stainless steel is very resistive, platinum is the perfect material to use but it's too damn expensive.
Low voltage, high amps is apparently the way to go or high voltage low amps pulsed at quite low frequency to keep temperatures down. I wonder how well 240v at 50hz rectified would perform?
With graphite plates the problem is that it's very sacrificial, no good as you seen, not for anode anyhow. We need to use an anode that can't be used for electroplating yet is very conductive and does not erode or corrode. If you think of a cost effective material that fits requirements please let me know 😊👍
what are the middle layers og graphite doing if there not connected?
Yeah the graphite experiment is quite interesting, I wondered why they're not connected too in such a small build.... I actually used a neutral plate every 3 stainless plates in my builds.
Instead of running your hose to the airbox, hook it to a "T"on the vacuum line going to your brake booster.
Tests should be conducted on vehicles with 5th generation GNV systems. As they already have more advanced equipment that allows changes in the systems and can better accept HHO. As an admirer of the HHO system here in Brazil, I am interested in learning more about its applications and benefits.
put a positive wire onto a tap with water, so that when the water drops out it carries a positive charge. then put your negative terminal onto some aluminium wire (like used for welding) when the positive water meets the negative aluminium, they should flash into 100% HHO, the byproduct will be aluminium oxide, which you can reuse again by smelting it back into aluminium.
Eu também tenho muito interesse nesse sistema, desejo troca de informações.
I am also very interested in this system, I want to exchange information.
Has anybody added hydrogen to a diesel engine? I'm afraid to try because of pre ignition. Yet just mentioning this, I can buy a one cylinder motor for $150 bucks I should test on this. Stanly myer was mixing exhaust gas with the intake to slow the pre ignition time down, just an fyi.
Put a big resistor With a potentiometer On it On your map and maf sensors and you'll get them in the proper parameters.
What is the psi of oxygen in it and how much electricity is being used
What's the advantage of Urea with KOH as electrolyte?
Every time the wire sparked I was cringing. Waiting for it to give free warm hugs
DOES sanding using an orbital pattern increase the surface area Sir ?? What about the sandpapers grit size ?? Thank you for your time. Peace v
200, 100 grit
why u don't use stainless steel?
Great, very informative experience except that oxy hydrogen (HHO) is dangerously explosive if the detonation is too strong!!!
it is better to complete the assembly with a separation system to obtain the hydrogen AND the oxygen each on their own
yes it's very explosive ,bubbler tank is very important.. oxyhydrogen is already good in the engine ..
Stop trying to scare people. Why are you here? Hmmm
@@CoincidenceTheorist Try to scare people!!! No, but am I dreaming or what? I'm just informing these people of a scientific truth that everyone should know
It's YOU who SHOULD normally warn them and you don't do it, you mislead them!!! and it’s serious!
Try doing this experiment on a small scale to convince them:
Don't forget that I am here because I choose to be
There's always one health and safety bot hiding, waiting for their opportunity to chat poo 🤣🤣
If you want to separate hydrogen and oxygen you can do it with a powerful magnet or electromagnetic as they are opposite magnetic polarity... That's what I came to say but the health and safety guru distracted my attention 🤣🤣👍
Use Platinum plated strips. Just 2 is all you need, extremely efficient and high production. Still, the H must be stored in tanks, compressed and regulated out that way.
Have you try using 4x LiFePo4 battery to replace accu in gasoline car. It saves fuel more than 10% and no maintenance needed.
Works for short time before you melt your piston rings, burn your valves then your car looks like a diesel... if you are going to run hotter gas you need to set the engine up for hotter burn.. then it works
Las dos placas de grafito del centro que función cumplen?las veo aisladas de las de los lados y sólo trabajan las de afuera.
es correcto. estan aisladas. funcionan como divisores de tension..
Urea and potassium hydroxide? So how do you dispose of the chemical mix that remains after electrolysis to exhaustion of the hydrogen?
Clean Your Drains With It?
Uh? Just add more water? Unless it is chemically altered in the process it is catalytic. I cant see anything harmful coming out, but maybe not pour it into a watercourse
What is the change in chemical out put from KOH to KOH with urea? Will we get anything different than just H2 O2?
bro how did you supply that much current and what type of power supply and other electrical componants did you use can you give a list of them
lithium battery or lead acid can supply those high current.
Can we use this project for cooking purpose ? what the upgrade thing to use this gas for cooking purpose ?? If i use 12 volt 220 amp then can we produce much gas for cooking purpose ??
Great build video. I am working on something very similar. Is there anyway for you to estimate how much gasoline was needed to replace the charge on the battery?
i can't compute it when it comes from the engine.. i don't have intentions to charge it from the alternator, instead it is solar or grid. it makes it cheaper that way
for a correct calculation of consumption you must also enter the parameters for the electricity you use, I don't think you have an 800W alternator in your car so the energy stored in your battery at the end of the test will be less. After all, the gas mixture you add is one of the most powerful fuels, so at the end of the your test in one case you only use petrol in the other one petrol add the detonating mixture H plus O. Having said this, I do not exclude the possibility that the system could provide greater returns.
Jika 3 liter per menit dan pakai susunan plat paling efisien yaitu -nnnnn+nnnnn- di jarak antar play 0,5-0,8 milimeter itu pun perlu setidaknya 600 watt sebab di kondisi paling efisien pun cuma 0,1 liter per menit gas HHO tiap 20 watt. Jika 3 liter per menit accu dan alternator tidak akan cukup untuk memberi supply daya. Kalau andaikata kurang efisien perlu 850 watt maka hasil gas dengan susunan plat seperti di video mustahil 3 liter per menit, separuh sudah bagus sekali. Perlu accu yg di charge. Maka bukan mobil ternaga bensin saja tetapi, mobil tenaga bensin + accu. Pengujian jangka pendek bagus cuma apa menguntungkan jika dipakai jangka panjang?
take a look at the amps, if You put an additional batteries for HHO this could give You something. But in general You will have a hybrid car, petrol-electrical.
flash positive charged water over a negatively charged aluminum wire. when they meet, they should create 100% hho with aluminium oxide as a byproduct, which can be heated back into aluminium.
Oh, this is interesting.
So ad a separate alternator? Room to make the amps.
Where does this equals on price to drive. And what will happen to the battery. Still efficient. I will still say yes
The physicist in me cannot agree that another alternator is the answer.
Many sensible suggestions about fooling the oxygen sensors on modern vehicles
As a chemist I don't understand why the urea or sugar has any effect (I would try washing up liquid to reduce bubble size and surface tension. I strongly advise more plates and lower voltage with higher amps to avoid waste heat
But good effort on the road test - after all that will convince others to have a go
I spent 3 years doing all kinds of experiments with hho, I even used Peltier tablets to cool the water, the Idea to know the consumption and use the scanner to know the injection time.
i think u should step down dc fuel pump and injector from 12v to 8-9v.
My opinion.give me your update..
Diesel is the solution. Gas engines are so badly designed. Older diesel, just pump it in the air intake.
th-cam.com/video/6zErilY7E-M/w-d-xo.htmlsi=Lg2xh78VnjLQjr9v
10% is good. Nice info on the W too. Heat is the issue. Maybe move plates apart a bit, or flow or cool water somehow?
Bro, nice build, awesome. Your car adjusts fuel and air to idle at as set number rpm. It was going up with hho but was then adjusting fuel to lower speed to hit target. Same when you removed hho and it went down then back up to target. Is that what you mean by 'automatically adjusts idle rmp depending on environment'?
as you state the pressure gets too high over 850. Although you have the setup for better containment already. that case for one! you just need to get some metal containers of somekind for the other parts that hold the electrolite?
then youill t need to worry about going up in flames!
Nem értem, a légszűrőn keresztül hidrogént jut a motorba?????
How do you control volts and Amps onto this HHO system??? 👍
the current is controlled by how much electrolyte you put into the mix, more electrolyte = more current.
as the solution warms up it becomes more conductive and can run away on you.
one way to help controlling heat is by useing six cells in series just like a car battery.
why didnt you do all the welding before you painted it instead of trying to weld it after you painted it?
amazing tips
Why didnt you connect all plates to power? 😮
the plates that are not connected are called neutral plates, to reduce the voltage and reduce heat that is created by the plates..
@albertnario4877 thanks bro
I didn't understand. Does your car do 20.5 km/l without hho?
How much electricity is required from battery to generate hydrogen from this generator?
Your alternator will probably make more than enough to keep up.
You know there's a nasty chemical left over when the stainless breaks down what you using in the water
What is this material? And how can we use this hydrogen to start a motorcycle?
ЦЕ ЧИСТА НЕРЖАВІЮЧА СТАЛЬ!!!!👍👍👍
@@SKAD_69 What??????
You can’t you would need another engine it can’t run on his car either he’s fooling people
faz uma celula que produza os gases separados e coloque no carro que funciona sem o combustivel do tanque. O Hidrogenio coloque um kit controlador de gas GLP e o oxigenio despreza, o tbi do carro que fará a dosagem.
I wonder how if u use ac current....
I worked with this a few years back but the nay-sayers got to me. Keep up the work. How is the fuel economy now?
Consider In day light, put some solar panels on your car and skip your voltage generator, use the sun to make the electricity and just see how you do with MPG.
Finely one really word test ride
Good work continue like that
My gosh you are very clever. Thanks for the video.
Молодец , возьму на заметку .
do you plan to carry out the experiment with HHO??
If you have the possibility I suggest you also test the separator system and share your thoughts with us
Thank you so much
планируете ли вы провести эксперимент с HHO??
Если у вас есть возможность, я предлагаю вам также протестировать систему сепаратора и поделиться с нами своими мыслями.
Большое спасибо
(Я не знаю, возможен ли автоматический перевод!!!)
Я сейчас очень далеко от дома по работе, по приезду домой хочу поэксперементировать@@slimel-gharbi8170
@@slimel-gharbi8170 никто в здравом уме не будет заниматься такой ерундой. У нас, в России, полно топлива.
Let's say your engine is 1L, 4 cylinder, and you make 2000rpm. That means 500L of a mix per minute. What will your 3L/min do to that volume?
Did you have any problems with your electrolysis cell getting hot? It appears to be a lot of current for the volume of the cell
it's getting hot without the PWM.
After just a few minutes, such a cell boils and the insulation that needs to be used is PTFE. another disadvantage is that stainless steel plates corrode and the electrolyte turns into green soup. For many years I have had contact with devices from OWELD, which produces such devices intended as gas welding machines. a better solution for a car is an oxygen cylinder with a volume of 5 liters and a tube leading to the air intake. The engine has a great kick. You have to be careful not to overheat the pistons.
In my opinion, generation of HHO makes only sense, if you have excess solar energy and want to have a fuel storage other than batteries. With 1 liter/min which I can get from a single panel, I get all energy I need for home usage. Due to its explosive nature of HHO, I would only store hydrogen in large containers, and sell the oxygen. For separation of the gasses, it needs a different build, though.
I Just though of something really interesting!
What if you installed that potentiometer on the gas pedal somehow so that when you press it down the voltage will increase so you can possably get even better milge so the Oxyhydrogen is more abundant when accelorating? would be even better if there was some sort of storage tank and pressure gauge with some regulators etc. is this something that could make tis even better? or too much?
Explosive!! There Is A Reason This Is Not Replacing Fossil Fuels!
hydrogen production by increasing voltage (not preferred) but current is. the impact of increasing current takes a few seconds to produce more Hydrogen, may not align with throttle response, just thinking not done it yet to tell you for sue
@@sridharboyana9250 sure, Sue here Kev won't go electric because of Lithium Battery fires but is happy to drive around with 100 litres of gasoline
I am literally scared of HHO, but this is a good video. I mean, hydrogen is explosive enough with air, less than 30 percent of oxygen. Even if you do not mix it perfectly.
Feeding it directly into an engine is not hazardous .
Hi interesting video, did you see fluid level drop down on start up = half you plate area non productive ...
To gain best plate coverage connect you're possative cable to upper / top of plate , current heads down plate looking for ground.....
Connecting you're negative to the bottom of plate block so current heads on up... Plate block.... Fit a fuse.
Look for better bubbler and bottles so you can fit safer
If you cut corners off left for possatve connection... Right for negative side connection... Keeps them seperate, less chance of shorting out ...
Do you use a different battery for this HHO ?
yes..
Add solar and lifeo4 battery, don’t run hho by alternator, you will get 40% better mileage
i already use a lithium battery to run the hho, that's my plan to use solar to charge the battery and run the hho using that battery..
Sir plate ka size or thickness please
I believe if you can find them iridium plated strips would be best because of the cost.
how big cell to produce 5lires per second
hello , is your channel open for sponsorship ?
I think your front co2 sensor need a service or change. Without hho it should get 17kpl and above. With hho it should get more millege.
هل نستغني عن البنزين نهائيا ام لا
অনেক সুন্দর করে ভানালেন ভাই
Did you notice any power gains from HHO?
i didn't notice any improvement on the engine power, maybe on carb type engine, you may notice the difference..
@@albertnario4877thanks for your honesty! Since you are putting some additional load ( via the alternator) on your engine in order to produce the HHO on board, even neutral power or/and fuel economy “gain” means , that HHO is helping at least a little bit with improvement of combustion .
@@flappingflight8537 no, I don't use alternator to provide power on HHO, I use different battery for it.
Is this graphite?
So the energy to split water into HHO comes from the alternator which typically runs at
The battery for the HHO is separated from the engine.. it has its own energy provider.. it is cheaper to charge the battery than to use fuel.. sorry for the poor explanation on that.
Tenaga taidak boleh dicipta Pak.
the big problem of that design is HEAT and low conversion of liquid into gas.
i suggest that you study or find the right resonance frequency of water; ;if you found it
you can now easily separate the hydrogen and oxygen very fast with 12volt and 3amp power supply only without additives'..and your reactor metal mush be like in a catalytic converter. hope this will help to your experiment
Co to jest za materiał którego użyłeś do budowy generatora
Be very careful browns gas explodes easily. Do you have a flashback arrestor?
Try using calcium carbonate / tooth brushing powder . It doesnt corrode .
That entire system would melt inside of 10-15 minutes. That thing is going to get so hot that it will explode. Plus, even if it were designed well, it would still be a huge net energy loss in a car.
He lost me when I saw him put complete seals around the outer parameters of each plate. I mean I know little about this. But isn't it supposed to be more free flowing around the plates than that?
@@InvestigationsDepartment That was probably to isolate the plates electrically.
*_To make a real difference you need at least 200 to 300 amps! I do like your 4 plate BI-POLAR CELL However!!! That's smart!!!!!!!!!!!!_*
Your plate sanding wasn't done right , that is done in a cross stich pattern by sanding diag top corner to bottom corner of the plate then do again corner top accross to bottom corner like an X pattern getting everything fully sanded both sides it makes a huge differance. Also port it in were the vacum on the brake master clinder connects faster delivery . Good Job well done
Despite your efforts I doubt that your reduction in petrol consumption is greater than the cost of the energy input for the HHO
Before or after taxation? He has already suggested ways and means of producing the H2 that do not use the alternator...or was that a different video?
Y COMO PARA QUÉ USAS 4 PLACAS SI SOLO FUNCIONAN 2 DE ELLAS.
You need work the correct amount of water.
When the acid level is at its peak. No more gas is made. Dont ask way. I dont know.
You need keep a clean but very small amount of water running in the tank. Hope it helps mick Australia 🇦🇺
En dónde encontramos la tarjeta y resto de cosas??
Tal vez no era para más potencia pero si para más peso eso k le puse en un auto iría haciendo maravillas x la carretera
make a manifold to separate the H from the O - 2 separate tubes. Brown's gas is too explosive.
also this is NOT a "Hydrogen" generator this is simply this generates a hydrogen and oxygen mix by electrolysis which is very inefficient (this is why it is NOT used to generate Hydrogen gas for cars or anything). This gas mix is highly combustible more than you will be able to handle in an engine bay and wondering how you would introduce this into the engine without blowing it up. 10% fuel economy just not possible counting everything you won't believe me anyways so not trying to give you the math ... .But why not just show the power used for this 3L .... in Watts or Joules then we can calculate how much "charge" Watt/h or you need to carry in your car as charged battery ... and maybe you can convince yourself that this is sorcery...
Looks wonderful - Canada
You produce hydrogen and oxygen gases. A very explosive mixture.
except the the energy expended on the electrolysis exceeds the energy that can be harnesses from the HHO. So would would be better off just putting the battery in the car & running an electric motor assist. Oh wait, somebody already did that...... 🙄
I want one, let me know how much.
tutto bello...e ben fatto peccato il discorso sul risparmio di carburante che non può essere vero. PErchè produrre l'idrogeno dalla batteria costa sicuramente più energia di quella che ne ricavi. E questo lo dice il primo principio della termodinamica. In ogni caso hai fatto un bel generatore di idrogeno.