3/4 drop from crown suspensions. 4" drop springs and 3" drop keys Beltech shocks on rear and front Snapchat & Instagram is @hugodiniro Contact me- hugocastillo3188@gmail.com
I have an 04 Denali that I want to fix up. It's such a nice vehicle and I've always thought about having rims put on it, but was not too sure. Yours looks really nice! Now I really want to invest in it!
So I don't see anybody asking this question, but how is the ride after installing this kit? I know it makes it ride not as good but was it a huge difference or not notice it to much? I have a tahoe and I want to do the 2 inch knuckles but the keys are much less money. The drop knuckles or spindles don't change the ride at all so just wondering what your opinion was. Thanks!!
I had been wanting to do that for ever. Finaly said f it and did it... Thank you for the view and comment. Be sure to subscribe to watch the next things I wanna do
I always had an idea of doing what you’re doing with this yukon denali. Its pretty cool to have a sleeper yukon. But i went with a srt8 jeep instead. Have you raced a tbss? I’d like to see how that’d go
Thank you for the view and comment. I’ve never raced a tbss. It’s kinda hard to get raced tbh. The only one that want to race me is cars and newer mode built trucks. With the Lt motors. I did a little pull with an srt8 jeep. I kept up till like 50-60. Then started pulling away. On my old set up. Just cam, stall and headers. I’m currently doing the whole top end as a matter of fact. Just need new map sensor and tune after that. Keep an eye out for that
Yo, i have an 02 yukon denali. Want to do the same. Install a drop kit. What kit can i install and run 26’s with no issues? Also keep my air ride suspension. Can you tell me the kit you have and where to order from?
I'm not sure, but I think I can still ride 26s fine. I have alot of room left. I looked around for kits but most of them were out of my budget, so i made my kit... and by that I mean I bought everything a separate times.. i bought the drop springs and keys from crown suspension.. i for the shocks from beltech... the kit was like 600... i got the drop springs and keys for 200.... back shocks for 110.. front shocms for 75.. so total like 385... so saved me over 200 dollars. And about the air ride suspension I'm not sure.. mine wasn't working any more so I just unhooked it.. but they should sell special shocks... or keep your shocks and use shock extenders.. thank you for your view and comment
La6Slow Castillo thanx for the info man. Really appreciate you getting back. My air ride dont work either. Does your “check air ride” light come on ever since you unhooked it?
@@marcotena4158 removed them, I pulled them out... i will need to go back and cut the free travel.. it hits a little. I don't like it. So cutting it should take of that problem
No problem, I hate when I ask questions and they never reply.. and no.. no light.. just om the dash where it says the miles it will say service air ride. But u can just hit ok and it will go away
I have a question brother, there is no problem if I only use torque wrenches and put new upper A weapons without changing the splinters, is there any negative consequence?
First, I would get cold air intake, port throttle body, port intake and get headers and a tune.. that alone will wake it up a good amount. I know a guy In the Dallas area that ports. He ported my stuff.. his Instagram name is 454chuy. You can mail him your intake and throttle body and he ships it back to you.. and if you want more power. A cam and stall is the next best thing.
La6Slow Castillo sheesh good looking compa not a lot of People are helpful like you my boii I stay in Los Angeles thanks bro I appreciate it I’m going to start of with the cold air intake
No problem, I kno its hard. I started out the same way, I would ask ppl and they would ignore my comment or questions.. fck em... but feel free to ask.. ill help you the best I can, don't forget to subscribe if you havent.
How does it ride i want to do this drop on mine but I have a baby on the way and I don't want it to ride like crap I mean I know its not going to ride like stock but i just don't want it to feel like I have 2x4s as shocks lol
It rides good. I drive it daily to work. Like a 15 min drive one way. Roads ain’t the best here either. U will need to cut off the extra bump stuff platform it has
Thank you for the view and comment. I got these as a gift. My buddy gave them to me for my birthday. But you can find them on eBay. Let me go see if I can get u a link
I just did a 4 inch drop in the rear and left the front stock but when I go over a bump it makes a clunking sound and when I brake it makes a knocking sound any ideas what it is?
Thank you for the view and comment. On these suvs. Where the bump stop goes. There is an extra piece that’s on the frame. You will need to cut that off It’s not the actual frame just be careful the gas tank is right behind it
You don’t installed a new bump stop bro you just left it like the you cut the plastic front in back if the tire was rubbing or not in too know where the right way too installed the bolt on a new torsion key
@@jaimeguadalupe216 le quietas el tornillo. Pones la clampa esa. Y eso lo aprieta y a la misma ves afloja la tension que tiene Y sacas la barilla y ya sale le llave. Luego pones la llave nuevA patras. Ya haces lo mismo pero de reversa
I just put the keys up front.. but went to low for me. So I'm going to raise it up about 2 inches and put the drop shocks I have and then go for the alignment. Right now it does have a bit of camber on it. Thank you for the view and comment. Be sure to subscribe. More videos coming very soon
Thank you for the view and comment. If it’s or daily. I wouldn’t go that low. I raised the front up an inch. I’m at at a 2/4 now. If you go that low. You will need to c notch the frame. And I got like 400 in my drop. I installed it my self
I have an appointment to get tuned today, I had some work done to the motor and it went down hill,I had went to get tuned and the denali wasn't cooperating... we had problems with harness.. problems with ecm... sensors acting up because the harness.. i replaced ecm... harness.. sensors all that good stuff.. so today hopefully we can get it tuned no problem. And power wise. I'm not sure to be honest, never had it dynoed.. but it feels pretty good.. if I had to put a number to it.. probably around 400 awhp. No more than that I don't think .. thank you for the view and comment, be sure to subscribe. Thank you
La6Slow Castillo Nice bro I have an appointment to get tuned Friday for my Awd Denali 6.0lq9 with btr stage 4 cam ,1 3/4 long tubes and A K&N intake. Just put the cam in not to long ago haven’t had the time to take it to a tuner
@@hugodiniro oh ok im trying to do a 2/4 drop on my 05 tahoe. I want to do the 2inch drop spindle or do you think just the torsion let will do the job? I just don't want my tires to butterfly
Thank you for the view and comment, I used a 3/4 drop from crown suspension. And beltech Street performance for shocks. But the 3 was to low for me. So turned the keys to make the front go up a little. So I'm at a 2/4 give or take
@@jesusruiz2980 I got it off eBay. I pieced it together. The whole kit was like 700. It was out of my price range. So I pieced mine and it was like 350 or 400
@@Squints1966 yes sir. Feel free to ask about anything. I hated when I would ask and they would give me smart ass replies or not even answer me. So I’m here to help the best I can
The kit I pieced together. Full kit was like 700 dollars but if you piece it. It comes out to like 400. If got crown suspension drop springs. Crown suspension keys. Beltech street performance drop shocks for front and rear. I can send you a screen shot of my purchase if you would like to see what exactly I got. I can send them thru snap chat or Instagram if you have either
I pieced it all together. It was cheaper that way. It was like 400. The kit whole was like 700. Of you have Instagram I’ll send you a screenshot of what I bought. Or Snapchat @hugodiniro on both
Your 6.0 is looking DOPE.... I have been trying to look for a kit for my 04 Denali AWD sitting on 22's.... if you can point me in the right direction it would be greatly appreciated... Added you on snapchat.... Pumba5274
Preciate the love, I got the 3/4. I turned the tortion keys up, so it's like. 2/4. The front was to low for me.. I got my drop pieced. A kit was like 500 bucks. I got my drop for 200. Just 4 inch drop springs in the rear, drop shocks. And the front 3" keys and drop shocks
Yes, mine is all wheel drive, has tortion keys, you can use your stock keys to go up or down a good 2 inches... i put the 3inch drop keys, and it went way low.. i have it as far as I can go up now, i got 4inch drop springs in the rear.. if you go that low or lower cut the plate off wherr the bump stop is...i didn't think I would be that low but I'm hitting on dips, so.i have to go back and get that free travel. It's on the frame, not part of the frame.. gives you a good 3 inch more clearance
I have an 04 Denali that I want to fix up. It's such a nice vehicle and I've always thought about having rims put on it, but was not too sure. Yours looks really nice! Now I really want to invest in it!
I love it. Mine is an 04 as well. Thanks for the views and comment
sweet ride man. glad i seen your video im ordering the kit today for my denali xl. gotta get my big girl low lol
Cleanest looking Denali if seen compa salute 💪🏻🙌🇲🇽
Thank you for the view, comment and compliment.. 🙏🙏🙏 don't forget to subscribe. More stuff coming
The 3-4 drop was just the tortion keys and coil springs
@@danielgallegos2107 I used drop shocks from beltech. Didn’t want to use shock extenders
@@danielgallegos2107 I’d recommend on getting spindles instead of keys. Keys give a little camber
I got a o3 Tahoe man should of got a Denali thing is clean af
Wow sweet great job I’m working on mine😊
You will love it.. I do and the compliments as well, thank you for the view and comment
Nice man plan on doing 2/4 drop on my 04 tahoe on 24s
Thats what I should of done... i had to turn the tortion keys all the way up. It was to low on the front. You won't be disappointed
What size tire u running
Hey boss what drop kit did you get for the 2/4?
It’s a 3/5. I should of went with a 2-4.
Barely seeing this boss. On the 24s I have 295/35-24
🔥👊🏾🔥 I’m about to do the 3/4 on my XL Denali on 24s also
Bout to be looking good. I love how big bodies look dropped on 24s. 22s look to small when they are dropped. Good choice
So I don't see anybody asking this question, but how is the ride after installing this kit? I know it makes it ride not as good but was it a huge difference or not notice it to much? I have a tahoe and I want to do the 2 inch knuckles but the keys are much less money. The drop knuckles or spindles don't change the ride at all so just wondering what your opinion was. Thanks!!
It rides good. But gave me a bit of camber. I will need to fix that
I need to do that to mine yours is sick
I had been wanting to do that for ever. Finaly said f it and did it... Thank you for the view and comment. Be sure to subscribe to watch the next things I wanna do
Love getting packages!! ❤️
Me too. Lol. But not when I get home and they're open by the wife lol
La6Slow Castillo lmfao 🤣🤣 she gotta know wtf you buying 🤣
@@lattyko she need her wig split
@@hugodiniro lol
Clean AF
Preciate ya
6.0 Gang gang
The bolt from the shock on top it don’t rub on your tire or you put it in opposite
No it don’t rub at all. Normally
Mine it does bro you think I could turn in too opposite ?
Mine rubbed on my burban i just added washers to pull the bold back @@jaimeguadalupe216
What did you use to drop the front ? Just torsion keys?
Yes. The front keys and drop shocks
I always had an idea of doing what you’re doing with this yukon denali. Its pretty cool to have a sleeper yukon. But i went with a srt8 jeep instead. Have you raced a tbss? I’d like to see how that’d go
Thank you for the view and comment. I’ve never raced a tbss. It’s kinda hard to get raced tbh. The only one that want to race me is cars and newer mode built trucks. With the Lt motors. I did a little pull with an srt8 jeep. I kept up till like 50-60. Then started pulling away. On my old set up. Just cam, stall and headers. I’m currently doing the whole top end as a matter of fact. Just need new map sensor and tune after that. Keep an eye out for that
@@hugodiniro will do. What part of texas are you in?
@@joellasierra west Texas. Plainview tx. Between Lubbock and Amarillo tx
Any issues with the air ride suspension after the drop? Wanting a 2 4 drop on my 05. Clean nali bud.
When I got the Denali it had air ride problems. So it wasn’t working so I didn’t ever use it. Just the normal shocks thank you sir.
Nice 😁. Thanks for the reply.
Looks good buddy
Thank you sir, thank you for the view and comment. 🙏🙏
Nice bro i have a denali to and i gotta say get the trailing arm relocater bracket u will thank me later
Thank you, I will look in to that, subscribe if you haven't. More goodies on the way
@@hugodiniro i did bro added u on the gram to 👌
@@boosted_sierra4264 already, preciate the support 🙏🙏🦍🦍
@@hugodiniro no problem bro 👌🔥💯
Yo, i have an 02 yukon denali. Want to do the same. Install a drop kit. What kit can i install and run 26’s with no issues? Also keep my air ride suspension. Can you tell me the kit you have and where to order from?
I'm not sure, but I think I can still ride 26s fine. I have alot of room left. I looked around for kits but most of them were out of my budget, so i made my kit... and by that I mean I bought everything a separate times.. i bought the drop springs and keys from crown suspension.. i for the shocks from beltech... the kit was like 600... i got the drop springs and keys for 200.... back shocks for 110.. front shocms for 75.. so total like 385... so saved me over 200 dollars. And about the air ride suspension I'm not sure.. mine wasn't working any more so I just unhooked it.. but they should sell special shocks... or keep your shocks and use shock extenders.. thank you for your view and comment
La6Slow Castillo thanx for the info man. Really appreciate you getting back. My air ride dont work either. Does your “check air ride” light come on ever since you unhooked it?
Did you remove the bump stops, or just replaced them?
@@marcotena4158 removed them, I pulled them out... i will need to go back and cut the free travel.. it hits a little. I don't like it. So cutting it should take of that problem
No problem, I hate when I ask questions and they never reply.. and no.. no light.. just om the dash where it says the miles it will say service air ride. But u can just hit ok and it will go away
Hey what’s up bro do I need to change shocks to lower my truck or can I just swap the springs. I’m putting 4 inch lowering springs on my Yukon 04 ???
I would do the shock as well. Because form being compressed so long. After while they will go out and ride like crap. Happen to me a few years back
I have a question brother, there is no problem if I only use torque wrenches and put new upper A weapons without changing the splinters, is there any negative consequence?
🔥 🔥
🙏🙏
Looks good bro I just order the 3" key and 3" springs
Hell yea. I bet it’s gonna look real good. I turned my keys cuz the 3 was to low for me. So. It’s like at a 2/4
Thanks man oh and what was the issue with the 3"
@@erickosolismartinez9523 just to low for my liking.
Oh ok cool I'm staying with the stock 265/70f16
Just got the springs today one question on the bump stop did U cut the metal the bumps sit on or just the bumps. I'm only lowering it 3" in the back?
Came out sikk what you think about a drop on a 4x4 Tahoe more problems or headache? then just buying a 2wd instead
It’s pretty much the same i believe. And yes I wish mine was a 2wd too haha
You just took off the bump stops you didn’t cut the part that holds them ?
Correct. I need to go back and cut the “travel mod”
Yo what can I do to my Yukon Denali 6.0 to make it go faster I have it stock rn .?? Can I change the headers bro .?? Or what can I do playa ??
First, I would get cold air intake, port throttle body, port intake and get headers and a tune.. that alone will wake it up a good amount. I know a guy In the Dallas area that ports. He ported my stuff.. his Instagram name is 454chuy. You can mail him your intake and throttle body and he ships it back to you.. and if you want more power. A cam and stall is the next best thing.
La6Slow Castillo sheesh good looking compa not a lot of People are helpful like you my boii I stay in Los Angeles thanks bro I appreciate it I’m going to start of with the cold air intake
No problem, I kno its hard. I started out the same way, I would ask ppl and they would ignore my comment or questions.. fck em... but feel free to ask.. ill help you the best I can, don't forget to subscribe if you havent.
@0:28 You have to blur out your info, your hand wasn't quick enough....
Feel free to send me soemthing lol
@@hugodiniro 🤣Just looking out bro. I know some snowflakes take things personal on social media and do crazy stuff with personal info. Be safe.
I wanna do a 2/3 drop on my tahoe. Do i need the drop spindles or the torsion keys
I did keys up front. But I believe you can use your stock keys to lower it 2 inches
What size rims you running bro your setup clean asf
They’re 24”. Wrapped in a 295-35 tire
Looks good man. How'd you lower the front?
Up front I used keys. Went to low so imma take the keys off and get spindles
Did u just use keys for the front and drop springs for the back? Or anything else added?
That was it. Drop shocks all around
How does it ride i want to do this drop on mine but I have a baby on the way and I don't want it to ride like crap I mean I know its not going to ride like stock but i just don't want it to feel like I have 2x4s as shocks lol
It rides good. I drive it daily to work. Like a 15 min drive one way. Roads ain’t the best here either. U will need to cut off the extra bump stuff platform it has
Nice
Now you need paint job differed rims and your good
Whooooo shit is hot!🔥
Preciate ya boss man
What u got on the front so it would look 3 inche drop on the front what u put on
Keys and drop shocks
Where u get the taillights bro I’m looking for them for a while but can’t find it
Thank you for the view and comment. I got these as a gift. My buddy gave them to me for my birthday. But you can find them on eBay. Let me go see if I can get u a link
www.ebay.com/itm/303023766877
@@hugodiniro thanks 🙏
So what did you guys do with the leveling rods?????
My air suspension didn't work any more, so it was just regular suspension
Ohhhh ok gotcha
I just did a 4 inch drop in the rear and left the front stock but when I go over a bump it makes a clunking sound and when I brake it makes a knocking sound any ideas what it is?
Thank you for the view and comment. On these suvs. Where the bump stop goes. There is an extra piece that’s on the frame. You will need to cut that off It’s not the actual frame just be careful the gas tank is right behind it
La6Slow Castillo it’s only coming from the left side
@@PabloMartinez-mp5mt probably a bad shock?
La6Slow Castillo so just cut it right I don’t need bump stops or to move the sway bar 2 inches? Also did you use a panbar?
@@PabloMartinez-mp5mt a lot of people take them off for clearance. I don’t have em
idk if i want a 2/4 drop on my 02 yukon on 22s or a 2in drop can you help me out on what you think?
If I'd do it again with 22s... I would go with a 2/3 drop with 285/45r22. Have a good size tires and fill the tire gap
You don’t installed a new bump stop bro you just left it like the you cut the plastic front in back if the tire was rubbing or not in too know where the right way too installed the bolt on a new torsion key
El bump stop no mas se lo quite. No corte nada. Y las llaves. Usamos una lleve especial y Luego salio sola. La lleve esa la rente en el auto zone
@@hugodiniro para poner nueva la llave y el tornillo lo tengo apretar como la primera llave ?
@@jaimeguadalupe216 le quietas el tornillo. Pones la clampa esa. Y eso lo aprieta y a la misma ves afloja la tension que tiene Y sacas la barilla y ya sale le llave. Luego pones la llave nuevA patras. Ya haces lo mismo pero de reversa
@@hugodiniro ok bro muchas gracias
@@jaimeguadalupe216 de nada
I have 05 gmc Yukon on 24s too will a 4/6 Drop fit ? I have low profiles on rims too
You will more than likely have to c notch it. This 4 inch drop barely clears. If I hit a dip with a loaded truck it bottoms out a bit.
Just got 4set of 17s stocks you think I still need to cnotch it for a 4/6 drop
I’m planing on doing a 2/4 drop my 04 Yukon, can I just drop the front 2 inches with the stock torsion keys?
Yes. I did it on my old Denali and cut springs in the back. But that was like 10 years ago. Did it the ghetto way on the rear
@@hugodiniro would u recommend it
I would do the front
Did u pass alignment with the front torsion keys bro
I just put the keys up front.. but went to low for me. So I'm going to raise it up about 2 inches and put the drop shocks I have and then go for the alignment. Right now it does have a bit of camber on it. Thank you for the view and comment. Be sure to subscribe. More videos coming very soon
La6Slow Castillo alright bro thx let me know if u have issues with alignment
How much would a cost to drop a 04 tahoe kit i want some 3/7
Thank you for the view and comment. If it’s or daily. I wouldn’t go that low. I raised the front up an inch. I’m at at a 2/4 now. If you go that low. You will need to c notch the frame. And I got like 400 in my drop. I installed it my self
Been a while since you posted it how much power is it making now?
I have an appointment to get tuned today, I had some work done to the motor and it went down hill,I had went to get tuned and the denali wasn't cooperating... we had problems with harness.. problems with ecm... sensors acting up because the harness.. i replaced ecm... harness.. sensors all that good stuff.. so today hopefully we can get it tuned no problem. And power wise. I'm not sure to be honest, never had it dynoed.. but it feels pretty good.. if I had to put a number to it.. probably around 400 awhp. No more than that I don't think .. thank you for the view and comment, be sure to subscribe. Thank you
La6Slow Castillo Nice bro I have an appointment to get tuned Friday for my Awd Denali 6.0lq9 with btr stage 4 cam ,1 3/4 long tubes and A K&N intake. Just put the cam in not to long ago haven’t had the time to take it to a tuner
@@xunhixunhi5609 hell yea. That thing is gonna move!!!
So did you only used the torsion keys in the front?
Keys and drop shocks that I haven’t put on
@@hugodiniro oh ok im trying to do a 2/4 drop on my 05 tahoe.
I want to do the 2inch drop spindle or do you think just the torsion let will do the job? I just don't want my tires to butterfly
I think you will need upper control arms either way. If you want 2”. I think the stock keys will let you lower 2”. Just back out the bolt. Is it 4x4b
What wheels are those?
These were 24” niche wheels. On a 295/35-24
I have 2002 Yukon denali And I am looking to drop it what the you use on your denali
Thank you for the view and comment, I used a 3/4 drop from crown suspension. And beltech Street performance for shocks. But the 3 was to low for me. So turned the keys to make the front go up a little. So I'm at a 2/4 give or take
Where did you buy them from since i live in Portland Oregon
@@jesusruiz2980 I got it off eBay. I pieced it together. The whole kit was like 700. It was out of my price range. So I pieced mine and it was like 350 or 400
@@hugodiniro I have a question I am trying to do at t up on my truck what kind of spark plugs and wires are you recommend
@@jesusruiz2980 thank you for the view and comment. I use ngk iridium plugs. And basic wires.
Did you have to change the rear end links and what did you use
I didn’t change anything. Shocks. Springs and removed bump stops
@@hugodiniro and you are on a 4inch drop spring by crown correct
@@Squints1966 yes sir. Crown springs and keys. Beltech shocks
@@hugodiniro thank you I appreciate your reply
@@Squints1966 yes sir. Feel free to ask about anything. I hated when I would ask and they would give me smart ass replies or not even answer me. So I’m here to help the best I can
Did you have to c notch the rear?
No sir. Just removed the bump stops and the little holder they come on
What size tire?
295/35-24 boss
Good video, but wasnt detailed as far as the leveling rods
Tell us where you got that kit. And how much bro
The kit I pieced together. Full kit was like 700 dollars but if you piece it. It comes out to like 400. If got crown suspension drop springs. Crown suspension keys. Beltech street performance drop shocks for front and rear. I can send you a screen shot of my purchase if you would like to see what exactly I got. I can send them thru snap chat or Instagram if you have either
@@hugodiniro no it's ok. I'll look it up . Thanks.
No problem. Thank you for the view and comments
@@hugodiniro I'll subscribe if that helps support your channel bro. If I have any questions I'll ask later. Thanks
@@superior3384 thank you
Which belltech shocks did you order ?
I used beltech street performance
@@hugodiniro thanks
@@bigc2092 Yes sir. Thank you for the view and comment
I like it. Check out my 03 Yukon Denali.
Where you get that kit at ?
I got it pieced. On eBay. The kit was like 5-700 bucks. Pieced together was like 350-400
What size tires do you have?
On this video I had 295/35/24 boss man
What size tire you running bro??
I run a 295/35 on a 24 inch rim
How much it cost to lower it ??
I had seen kits on line for like 6-700. But I pieced mine together. Ended up being like 400 dollars.
U got the kit number?
I pieced it all together. It was cheaper that way. It was like 400. The kit whole was like 700. Of you have Instagram I’ll send you a screenshot of what I bought. Or Snapchat @hugodiniro on both
Can I get the link to the kit ?
Let me see if it’s still in my emails.
La6Slow Castillo ok thank you bro 😎
@@josea9409 do you have snap chat or Instagram. I can’t send you screenshots of what I bought. @ hugodiniro for both
👀👀👀
😍😍😉😉
How’s the ride
Its good, I still haven't put the dront drop shocks... but rides real good...not bouncy at all
Your 6.0 is looking DOPE.... I have been trying to look for a kit for my 04 Denali AWD sitting on 22's.... if you can point me in the right direction it would be greatly appreciated...
Added you on snapchat....
Pumba5274
Preciate the love, I got the 3/4. I turned the tortion keys up, so it's like. 2/4. The front was to low for me.. I got my drop pieced. A kit was like 500 bucks. I got my drop for 200. Just 4 inch drop springs in the rear, drop shocks. And the front 3" keys and drop shocks
Aye bro is yours awd I have the same one just someone told me I can’t because it’s awd just curious??
Yes, mine is all wheel drive, has tortion keys, you can use your stock keys to go up or down a good 2 inches... i put the 3inch drop keys, and it went way low.. i have it as far as I can go up now, i got 4inch drop springs in the rear.. if you go that low or lower cut the plate off wherr the bump stop is...i didn't think I would be that low but I'm hitting on dips, so.i have to go back and get that free travel. It's on the frame, not part of the frame.. gives you a good 3 inch more clearance
Oye La6Slow Castillo me guesta tu yukon guey nice orale
La6Slow Castillo Exhaust???
Munchas gracias
Where you get that kit at ?
I pieced it together. The kit would of been like 700. I ended up paying like 400.
What kind of beltech shocks are those?
Sorry barely seeing my comments. I used beltech street performance