BLDC motor speed controller ESC using irfz44n mosfets
ฝัง
- เผยแพร่เมื่อ 6 มี.ค. 2024
- BLDC motor speedcontroller ESC using irfz44n mosfets
Simple BLDC Motor Controller ESC circuit
how to make bldc motor controller esc circuit
Brushless motor controller circuit
bldc motor controller circuit
bldc motor controller esc circuit
#motor
#220v
#creativetechos
#quarktwin
Easily source your all components here.
👉www.quarktwin.com/
1：Quarktwin is an Independent distributor of electronic components.
Committed to the integration of electronic components distribution services of world-famous brands.
2: Have over 2300 qualified suppliers.
3: Provide over 1million SKUs.
4: Fast delivery
Thanks For Watching
I hope this video was Useful and you liked it
If you did ! Press the thumbs up button.
Subscribe It's Free ❤️
/ creativetechos
Join fb Group: / 819126578700997
Follow Page: / creativetechvids
Pinterest:
pin.it/4e3XuVu
Beautiful work
Meus parabens amigo ficou shom👏👏👏👍
Thank you very much my friend. How can I control the brushless motor of the gimbal?
Can i used this circuit BLDC 12 volt triple phase cylling fan ?
Can I use A2212/6T 2200 KV Motor ? else please guide for any alteration
Muito bom, parabéns eu também monto projetos aqui no TH-cam.
How many voltage given to circuit
5:10 Did you have to start it by hand, I see a break in the video where I think you might have done that?
Bro please suggest can I use 10k resistance in (half watt) ????
I liked your project, thx.
Glad to hear that!
very funny he applies the thermal compound to only side - guess he does not understand
Tack soldering is a VERY poor method
awful construction
no BOM
no details
no explanation
How much input?
Hello what is the right connection of diode's? In your film three bottom diodes are connected to the gates of mosfets, and between 3:42-3:57 two of them are connected to Drain of Mosfets? In my opinion connection to the gates doesn't work properly with 3 wires bldc motors?
Bleah man
How does it work
Great content
very funny he applies the thermal compound to only side - guess he does not understand
Tack soldering is a VERY poor method
awful construction
no BOM
no details
no explanation
Guys i need to bldc controller circuit diagram 12 to 36 volt with video
make sure 100%working after giving me
😊😊😊
very funny he applies the thermal compound to only side - guess he does not understand
Tack soldering is a VERY poor method
awful construction
no BOM
no details
no explanation
Good video❤❤
very funny he applies the thermal compound to only side - guess he does not understand
Tack soldering is a VERY poor method
awful construction
no BOM
no details
no explanation
Good 💯
very funny he applies the thermal compound to only side - guess he does not understand
Tack soldering is a VERY poor method
awful construction
no BOM
no details
no explanation
What's power ?
This circuit works only for wire connections common wire is necessary
Can I Test Electric scooter Bldc motor?
Yes
Отлично!
very funny he applies the thermal compound to only side - guess he does not understand
Tack soldering is a VERY poor method
awful construction
no BOM
no details
no explanation
Hello 👋
Can I use z44 mosfet?
Yes absolutely you can use
very funny he applies the thermal compound to only side - guess he does not understand
Tack soldering is a VERY poor method
awful construction
no BOM
no details
no explanation
…
como se si funciona
Boss super boss how to makeup U V W TESTER please makeing
one video boss
+1
Is is IRF3205
مافائدة العازل البلاستيك اذا البرغي وصل بين الموسفيت والألمنيوم
البرغي ماوصل الى الالومنيوم فقط مثبت على سطح الموسفت
Manque quand même le minimum gaz et l’arrêt
Circuit not working bro 😂
Use separate heat sink, or use thermal tape.
How to run hard disc motor by this circuit
no
No funciona
Muchas gracias
Lo realice igual y no sirve
make + from common then it will works i tried ad ok
В этих двигателях нет общего контакта@@gn-ne1ed
कैसे गुपचुप से रहता है? काम कर दिखाना न तो चाहता है लेकिन मुंह में दही जमा रखे है, या बोलने मे शर्म आती है, इससे अच्छा चूड़ी पहन कर बैठै जाओ |
Ни чего не работает.
Он допустил косяки в схеме, в конце видео он исправил их.
До этого видео собирал подобную схему. Не заработала но если надо мне подумать над ней.
Однако если убрать диоды то нужно будет подтолкнуть движок для, запуска.
@@FIL_KILLER что за косяки ?
@@kabalvlad походу вся схема это косяк.
Собрал в точности не заработала.
Движок просто фиксируется а одном месте.
Даже если крутить.
Косяки у него были, когда припаяные диоды те что на низу были один на затвор два на сток.
Ну корлче один крайняя нога. И два средняя
Потом он все перепаял на затвор. .
Кажется Легче на ардуинке сделать.
P. S. Использовал мосфеты с материки.
Ubd: 09.05.25
P. S. S. нашёл видео где чел разбирает схему, по сути надо затачивать схему под мотор индивидуально схема работает не со всеми моторами. короче проще не извращаться а купить готовый контроллер За 500 рублей на али и не морочить голову.
Este video es una estafa, no funciona , es mentira deberían quitarle el canal a creadores de contenido falso como este
Hi, I design BLDC/PMSM drives for a living. Kindly do not do this.
Where is the mosfet no
3205
irfz44n mosfet