Thank you so much for this video! I replaced mine in my Odyssey and was still catching error codes for it, I see now I need to reset it and kept the nuts loose to find the proper position since I didnt mark it before removing the old one. I've watched countless videos on removing/replacing but NO ONE said to mark the old one! Because of the way I've put it on It tilts too much to the left because I had to adjust the shift cable arm to get it back on which was wrong! I was stressing over the work I had done and am relieved to know it's a simple fix! Now to go finish the valve seal gaskets on my other odyssey 😑😬
Hey man, nice work. I have a question. My D4 light was blinking and Honda said it needed a new transmission. It's a 2002 accord (I know, this car is known for Transmission failure). Anyway, we bought a transmission kit, changed that, new Torque Converter, new Valve body and Solenoids as well. Now the car shifts into gear and drives, except in reverse. It goes in reverse but does not move. I did some research and found your video. So now I'm wondering if you think this may be my issue? I didn't get a code but that could be because my battery is dead and I had to jump start it since it's been parked for so long. I also hear that the Transmission fluid matters. I used a Valvoline Maxlife Multi-Vehicle full synthetic ATF. On the back it says it works with Honda DW-1.
You did the job yourself? Probably reverse gear is bad, and you should get Honda transmission fluid only! This transmissions don’t like any other fluid
Excelente tutorial como todos los que haces, estimado amigo. Tengo un problema relacionado con la tapa de este interruptor, tengo un Honda Accord EX 1998, 2.3 litros 4 cilindros, se me perdió la tapa y no la consigo por ningun lado. Mercado Libre me ofrece una para Honda Odissey 1999-2004, pero no se si le ajusta. Saludos cordiales.
Once again, great video. I sent you a question on the other video, thanks for responding. JUST WANT TO DOUBLE CHECK- The green light is blinking on the D4 (2001 Accord). The codes that came up are the general P0700 and then the P1705 which indicates the gear multi position. So am I still replacing the transmission range sensor?
off topic for a sec, your accent is dope asf. back on the TRS. what if I pull one from the junkyard? and is it crazy to just me, that lil bore put the car in gear.
@@BulletSolano now my concern is you mentioned installing it from the neutral position. Is it the same even if it isn't new, and/or do I do it in reverse and is the smallest part the sensor?
Hey Bullet , Hope you can help me again , I`m still having trouble with my 2000 accord , now that iv`e checked everything out it seems that all of a sudden it`s not getting gas, now last week or so it ran great , but this time i was still trying to stop this oil leak again . so iv`e checked my spark , thats good , iv`e checked timing , thats good , so why would i not be getting gas of of a sudden when that has not been an issue before ?
Hey Doug, i think that’s the mechanics biggest problem, when you fix something everything else goes wrong, for some reason but that happens all the time. Check is the fuel pump is working because when you check the fuse box maybe you change move or do something in there, hope is not the case
So the continuity has to be checked to find out what the problem is ? Or do you just change the sensor and that will solve the problem? My car had codes p0705-6
For mine it was intermittent no start. I replaced everything in the starter sequence trying to chase this issue and never heard of this part until the day before it gave me the error code. It left me stranded a TON of times and I never understood why. It wasn't until I got mad and hit the shifter and it started that the lightbulb went on.
Thanks for the video…I have a question ,my accord 2004 v6 has a delayed reaction when you shift it to park to reverse and reverse to drive any idea what’s the problem?
Thanks for the video. I have a question, I bought a transmission replacement for my Acura Integra 2000. The transmission that I bought has a Transmission Range Sensor and my old transmission (the one the car came with) doesn't have one. Should I install the purchased transmission without plugging the transmission range sensor? Thanks!
I was hopping you could help me out, I'm having g a code p1705 gear position switch low input but I'm not really seeing any simptoms on the car everything seems to be working fine, I was told to replace the transmission range sensor, would you agree with that??
What if the car cranks, will not start and you cannot move the shifter out of park without putting a screw driver into the "bypass" switch? It will also not start in neutral. Sometimes it runs. I may wait 30 minutes, then it MIGHT run. Could this be the position sensor?
Tengo el código p1706 desde hace un mes, y buscando información en la Web me sale que tengo que checar el conector del sensor y verificar los cables que quizás están mal ajustados el conector
Hi Bullet . My civic 2002 has very high rpm and not moving in drive & reverse . I thought it was the transmission range switch . But got no codes . Do you think the transmission is finished ? Thank Al.
Bullet Solano Hi Bullet. Thanks for your reply . It has been a good car , 19 years old time to go . Or a reconditioned transmission. I will be watching for your next video. Thanks again Al
While changing my range sensor on my crv the gear selector was moved from neutral to reverse when the range sensor was off. Will this process work for my dumb mistake?
Buenas amigo ! Tengo una pregunta cambie mi neutral safety swicht lo compre nuevo pero parece que se movio un poco al ponerlo y no habia marcado la posición como hago para dejarlo bien ya que ahora me marca el código p1706 de antemano gracias
What if you put a jdm transmission with low miles and the d4 light starts blinking again? Worked for a few days now my trans acting up again ordered some new shift solenoids don’t know what else to do do u know if this will work or any info on jdm transmission swapped into a 3.0 accord 2000?
@@BulletSolano one last thing do you know which solenoids are sensors I need to transfer over to the jdm version? I’m new to 6th gen accords really need help thanks if u can
@lililililililil-7814 this is what I found online!!! DO NOT USE A JDM TRANSMISSION IN YOUR 1ST GEN CR-Vs. After I ordered a jdm trans for a customers 1999 cr-v and installed it the CEL kept coming on with a p0740 ( tcc lock up mailfuncation ). P0740 is set when the pcm sees a difference in rpms from the engine and transmission input shaft. So after i replace a torque converter at the request of the jdm parts supplier i got the code again, and as per honda's service manaul if the code sets, the line pressure is good, and the tcc solenoid pack is good then the transmission is faulty. we installed a second jdm transmission that the supplier sent us and what do you know after going 2 miles down the freeway the Check Engine Light is back on... p0740... After noticeing a shim on the input speed sensor thats not not on the usdm speed sensor i decided to count the teeth on the gear that the sensor reads off. 38 teeth on the US trans 40 teeth on the jdm trans That will cause about a 20% difference in the rpm reading between the engine and trans thus causing a P0740 every time..... A jdm ecu may get rid of the CEL but its not OBD for US emissions and you will not pass emissions.
@@BulletSolano so what ur saying is this trans doesn’t work for my 2000 Honda accord 3.0 sedan the trans I purchased was a JDM 98-02 Honda Accord V6 Automatic Transmission J30A 3.0L 99 Acura TL B7VA 4Spd alliance jdm-alliance
It was easier then I thought new one came in park so I moved it to the same position as the old one and that the car was in it just like a puzzle and keeping everything in the same position great vid man
If the relay have a diagram get power from the battery and get 1 side to the power and 1 to the ground with 2 cables, place the cables in the relay if you hear a click that means that the relay works
Hey Bullet ! hows it going ? just wanted to let you know what happened with my honda . Well your not gonna believe it but there was nothing wrong with car at all , I was using the wrong key to crank car with . I t so happened that I found a key holder inside strut housing and was a key that was made by original owner to open doors with and kit never dawned on me till another friend reminded me of it . so i went got my other set of keys and it cranked right up ! . man does that Dumbass crown belong to me or what !!! anyways car runs great now and no leaks of any oil and water . .... thank god finally . now i gotta replace clutch slave cyc. I do have a question for you tho. Is it hard to prime it ? and how do I do that ? will check back with you after work this evening
@@BulletSolano I got a new one. bro thank you so much. I spent an hour or so messing with it yesterday giving myself headaches and I spent an hour or more this morning messing with it and I’m not sure what I did but it works now. Thanks again so much. I think it does have to be in neutral and you really have to be careful to line it up EXACTLY where it is supposed to be.
TPS has noting to do with the transmission, but when you change the throttle position sensor is really difficult to put it in the same place, that’s why I never mess with it, my suggestion is to get a use throttle body from the junk yard put it on and see if that helps
Mira yo saque el mio y lo limpie pero estaba en park y asi mismo lo volvi a poner pero pero no me ilumina cuando lo muevo a d4 las demas si se iluminan qe puede ser?
Se movió, ponlo en neutral después quítalo el sensor y ábrelo y mira que esté en medio si no está en medio ponlo ahí y pon todo pa tras pero deja el auto en neutral
after a transmission replacement on 2006 honda crv i was getting a P0706. I replaced the transmission range sensor but now the car is cranking but isn't starting. I tried to use starter fluid to start car and it didnt start so i suspected an ignition problem and none of the coils will produce a spark when putting another spark plug. did i mess something up with the transmission range sensor? I tried to follow everything by the video. please any advice?
I don’t think you did something wrong with the transmission range sensor, but when you did the installation the car was in neutral? If so just check the 3 main things air, spark and fuel
@@BulletSolano yeah i made sure it was in neutral. And i have no spark. There isnt a check engine light. The car not starting bcus there isnt spark but idk what exactly the problem is. What would you do?
When you driving the transmission fluid level gets high probably that’s why the code goes away, check the transmission fluid level and connections of the sensor, also if you have that code the sensor probably is bad anyways
Bullet Solano llame al dealer de la honda y cuesta más de 300 dólares... y en las tiendas de auto Partes cuesta mas de 100... en los deshuesaderos no se si encuentre alguno. Muchas gracias bullet solano
@@BulletSolano thank you... thanx for replying at a timely matter.. Iv changed it to the old one before I did I cleaned it out but still the same code.
@@BulletSolano so I was getting tired of the issue so I changed it out One more time ,I opened the New one realized it wasn't on neutral closed it back up , installed it and no more p0705. Lol
@@BulletSolano but I don't know what that code will be because I bypass it and scan from the board and it blinks 5 times. D4 is the only code that it is giving me.
@@BulletSolano i just want to know where the number is for the transmission , i have the motor number " J30A1 2104906 " but can not locate the transmission tag or number
Hello, i’m hoping you can help my husband and I. He replaced the transmission range sensor to our 2007 Honda Odyssey. After changing it, the gears for drive and neutral will no longer light up, but the others do. It’s still shifting, but not sure what happened with those specific gears no longer lighting up.
Honda Civic 2001 automatic transmission in my vehicle and the address given in the video as I do flare. th-cam.com/video/G35Irz1Cno4/w-d-xo.html please help me. The transmission oil has changed the problem continues.
Thank you so much for this video! I replaced mine in my Odyssey and was still catching error codes for it, I see now I need to reset it and kept the nuts loose to find the proper position since I didnt mark it before removing the old one. I've watched countless videos on removing/replacing but NO ONE said to mark the old one! Because of the way I've put it on It tilts too much to the left because I had to adjust the shift cable arm to get it back on which was wrong! I was stressing over the work I had done and am relieved to know it's a simple fix! Now to go finish the valve seal gaskets on my other odyssey 😑😬
I’m glad this video help you
1st bro haha I’m always supporting fellow 6th gen Accord guys
That tip worked for me. Thank for saving me $80 bucks
No problem
and to think every bit of my problems all started with the timing belts snapped and now the whole top of engine is brand new
Hey man, nice work. I have a question. My D4 light was blinking and Honda said it needed a new transmission. It's a 2002 accord (I know, this car is known for Transmission failure). Anyway, we bought a transmission kit, changed that, new Torque Converter, new Valve body and Solenoids as well. Now the car shifts into gear and drives, except in reverse. It goes in reverse but does not move. I did some research and found your video. So now I'm wondering if you think this may be my issue? I didn't get a code but that could be because my battery is dead and I had to jump start it since it's been parked for so long. I also hear that the Transmission fluid matters. I used a Valvoline Maxlife Multi-Vehicle full synthetic ATF. On the back it says it works with Honda DW-1.
You did the job yourself? Probably reverse gear is bad, and you should get Honda transmission fluid only! This transmissions don’t like any other fluid
I am doing this Tuesday. Thank you brother!
No problem bro
Awesome information aloha from Oahu,Hawaii.
👍🏽
Can you do a video on how to remove the shift solenoids from the transmission
Yes is coming
Excelente tutorial como todos los que haces, estimado amigo. Tengo un problema relacionado con la tapa de este interruptor, tengo un Honda Accord EX 1998, 2.3 litros 4 cilindros, se me perdió la tapa y no la consigo por ningun lado. Mercado Libre me ofrece una para Honda Odissey 1999-2004, pero no se si le ajusta. Saludos cordiales.
Que tal, no estoy seguro si es la misma, revisa el número de parte en la página de Honda y ve si son iguales
Muchas gracias, amigo. Eso voy a hacer. Excelente día
Once again, great video. I sent you a question on the other video, thanks for responding.
JUST WANT TO DOUBLE CHECK- The green light is blinking on the D4 (2001 Accord). The codes that came up are the general P0700 and then the P1705 which indicates the gear multi position. So am I still replacing the transmission range sensor?
Really appreciate you bro!
If you have blinking d4 replace pressure switches and adjust A-B solenoids
Okay will do, I'll let you know.@@BulletSolano
Hey bro, it was the Transmission Switch sensor. So far so good. Thanks for sending me in the right direction.
No problem
Wish this guy worked WRX lol
off topic for a sec, your accent is dope asf.
back on the TRS. what if I pull one from the junkyard?
and is it crazy to just me, that lil bore put the car in gear.
Thanks, Yes get one form the junkyard
@@BulletSolano now my concern is you mentioned installing it from the neutral position. Is it the same even if it isn't new, and/or do I do it in reverse
and is the smallest part the sensor?
Yes, if the sensor is from the junkyard open it put it on neutral before installation
Thanks for sharing your video. Question: what about if you are swapping transmission, do you need to put in NEUTRAL OR PARK?
Neutral
@@BulletSolano thanks man
Good video bro thanks
Thanks bro
Replacing mine today. Thanks, Bro!
Nice, no problem bro
@@BulletSolano Worked like a charm. Thanks again.
Robt Fern nice
Estuvo bien bonito ese vídeo bien está bien explicado Me gustó muchísimo
Gracias
Hey Bullet , Hope you can help me again , I`m still having trouble with my 2000 accord , now that iv`e checked everything out it seems that all of a sudden it`s not getting gas, now last week or so it ran great , but this time i was still trying to stop this oil leak again . so iv`e checked my spark , thats good , iv`e checked timing , thats good , so why would i not be getting gas of of a sudden when that has not been an issue before ?
Hey Doug, i think that’s the mechanics biggest problem, when you fix something everything else goes wrong, for some reason but that happens all the time.
Check is the fuel pump is working because when you check the fuse box maybe you change move or do something in there, hope is not the case
ok but I didnt do anything to fuse box at all@@BulletSolano lol and your right about when you fix or try to fix something , something else happens
Yea that happens to my all the time, but yes check the relay I hope is that the problem
GREAT video thank you!!!
No problem
K hase ese sensor en la transmission? Yo Tengo UN 2.3 y golpea la transmission Al cambiar los cambios? X k ?
Thank you Carnal.
De nada carnal
So the continuity has to be checked to find out what the problem is ? Or do you just change the sensor and that will solve the problem? My car had codes p0705-6
Yes you have to check for continuity on both connectors the one from the sensor and the one from the car
Thanks for the video! What goes wrong usually with this switch?
Car won’t start, or you can’t move the gear lever
For mine it was intermittent no start. I replaced everything in the starter sequence trying to chase this issue and never heard of this part until the day before it gave me the error code. It left me stranded a TON of times and I never understood why. It wasn't until I got mad and hit the shifter and it started that the lightbulb went on.
What’s your favorite color?
P1705 is a gear shift malfunction just like the P1706? Should I replace the range sensor?
Yes
By the way new sub
Mine is 2005 but it has "p1717 reverse no position" .but the car works just fine
Thanks for the video…I have a question ,my accord 2004 v6 has a delayed reaction when you shift it to park to reverse and reverse to drive any idea what’s the problem?
Probably your solenoids are dirty, clean them and replace your transmission fluid
@@BulletSolano thank you I will do that👍
Thanks for the video. I have a question, I bought a transmission replacement for my Acura Integra 2000. The transmission that I bought has a Transmission Range Sensor and my old transmission (the one the car came with) doesn't have one. Should I install the purchased transmission without plugging the transmission range sensor? Thanks!
No problem, the old transmission is manual? and the new one automatic?
Automotive Solano they’re both automatic
So is there a way of making the one I purchased work?
Before you do the installation make sure the new transmission is the same year like the old one
Automotive Solano thanks a lot, keep up the good work!
I was hopping you could help me out, I'm having g a code p1705 gear position switch low input but I'm not really seeing any simptoms on the car everything seems to be working fine, I was told to replace the transmission range sensor, would you agree with that??
Opened and clean it up, if that doesn’t work replaced it
@@BulletSolano cool I'll check it out, thanks for taking the time to respond really appreciate it 👍
I have this code does it mean I can repair the part myself like you just did ? Or do I need a new part
It depends, try to clean it and go from there
What if the car cranks, will not start and you cannot move the shifter out of park without putting a screw driver into the "bypass" switch? It will also not start in neutral. Sometimes it runs. I may wait 30 minutes, then it MIGHT run. Could this be the position sensor?
I have replaced the throttle position sensor. If that doesn't work The shift position sensor will be next. I think the only thing left is the ecu.
Scam the vehicle for codes, before you spend money guessing you he problem
I will try changing my Ford Escape it’s under coolant hose I have an p0707
After replacing transmission range sensor, the shift is hard to switch, and with a noticeable kick from P to R or N/D
What have I done wrong?
Check for codes
What kind of tire size and rim size do you recommend on a stock height Honda Accord 2001 lx 4 door
I recommend 225/45/17
hello good video Could you tell us where the P0706 transmission range sensor precision sensor is in a 2011 Sonata please
Look is the side of the transmission
Tengo el código p1706 desde hace un mes, y buscando información en la Web me sale que tengo que checar el conector del sensor y verificar los cables que quizás están mal ajustados el conector
Hi Bullet . My civic 2002 has very high rpm and not moving in drive & reverse . I thought it was the transmission range switch . But got no codes . Do you think the transmission is finished ? Thank Al.
Hi, yes the transmission on 2001 and 2002 civics are bad transmission, you need a new one
Bullet Solano Hi Bullet. Thanks for your reply . It has been a good car , 19 years old time to go . Or a reconditioned transmission. I will be watching for your next video. Thanks again Al
No problem, thanks
Nice
Is this the same con an Accord V6 99 or Accord 2.2 95?
Thankyou so much
No problem
👍🏻💯
While changing my range sensor on my crv the gear selector was moved from neutral to reverse when the range sensor was off. Will this process work for my dumb mistake?
Yes
Bullet Solano thank you
Your welcome
What's up Bullet? How do I fix the P1705 code? Is it a sensor or solenoid.
Replace the sensor
Buenas amigo ! Tengo una pregunta cambie mi neutral safety swicht lo compre nuevo pero parece que se movio un poco al ponerlo y no habia marcado la posición como hago para dejarlo bien ya que ahora me marca el código p1706 de antemano gracias
Pusiste el sensor con el auto en neutral?
Do you recommend getting used parts on line like Bonanza sells this part for 48.00
If they have guarantee on their parts yes
Bullet Solano ok Thankyou so much
No problem
What if you put a jdm transmission with low miles and the d4 light starts blinking again? Worked for a few days now my trans acting up again ordered some new shift solenoids don’t know what else to do do u know if this will work or any info on jdm transmission swapped into a 3.0 accord 2000?
Transmission fluid was clean when you put it on?
@@BulletSolano one last thing do you know which solenoids are sensors I need to transfer over to the jdm version? I’m new to 6th gen accords really need help thanks if u can
@lililililililil-7814 this is what I found online!!!
DO NOT USE A JDM TRANSMISSION IN YOUR 1ST GEN CR-Vs. After I ordered a jdm trans for a customers 1999 cr-v and installed it the CEL kept coming on with a p0740 ( tcc lock up mailfuncation ). P0740 is set when the pcm sees a difference in rpms from the engine and transmission input shaft.
So after i replace a torque converter at the request of the jdm parts supplier i got the code again, and as per honda's service manaul if the code sets, the line pressure is good, and the tcc solenoid pack is good then the transmission is faulty. we installed a second jdm transmission that the supplier sent us and what do you know after going 2 miles down the freeway the Check Engine Light is back on... p0740...
After noticeing a shim on the input speed sensor thats not not on the usdm speed sensor i decided to count the teeth on the gear that the sensor reads off.
38 teeth on the US trans
40 teeth on the jdm trans
That will cause about a 20% difference in the rpm reading between the engine and trans thus causing a P0740 every time.....
A jdm ecu may get rid of the CEL but its not OBD for US emissions and you will not pass emissions.
@@BulletSolano so what ur saying is this trans doesn’t work for my 2000 Honda accord 3.0 sedan the trans I purchased was a JDM 98-02 Honda Accord V6 Automatic
Transmission J30A 3.0L 99 Acura TL
B7VA 4Spd
alliance
jdm-alliance
@lililililililil-7814 gear is different that’s why you have that code
Could this switch cause the car to jerk into Reverse or drive? Also the D on the dash does not illuminate
Probably your transmission is going bad, check for codes, and the light on your dash is a bad bulb
Go to advance if check engine light is on it probably is this part it be p0705 code
Do all transmissions range sensors come in nuteral ? I’m going to replace one on a for focus.
Check the instructions on the new on, but for what I know yes
It was easier then I thought new one came in park so I moved it to the same position as the old one and that the car was in it just like a puzzle and keeping everything in the same position great vid man
Nice
Hey bro do you know why I got code p1705 and my 2001 honda accord 2.3l will not shift to 3rd or 4th. It only goes from 1st to 2nd and that's it.
Hey bro you meet to replace the transmission range switch
will the fuel relay just go out like that ? the fuse for the fuel pump is good also
Doug Allen maybe but not sure, I hope is just the relay and not the fuel pump
@@BulletSolano yeah me too , ok now what is the best way to know if it`s the relay ?
If the relay have a diagram get power from the battery and get 1 side to the power and 1 to the ground with 2 cables, place the cables in the relay if you hear a click that means that the relay works
That’s the easy way to check them
Hey Bullet ! hows it going ? just wanted to let you know what happened with my honda . Well your not gonna believe it but there was nothing wrong with car at all , I was using the wrong key to crank car with . I t so happened that I found a key holder inside strut housing and was a key that was made by original owner to open doors with and kit never dawned on me till another friend reminded me of it . so i went got my other set of keys and it cranked right up ! . man does that Dumbass crown belong to me or what !!! anyways car runs great now and no leaks of any oil and water . .... thank god finally . now i gotta replace clutch slave cyc. I do have a question for you tho. Is it hard to prime it ? and how do I do that ? will check back with you after work this evening
Is yours a automatic or 5 speed amd does it matter ?
Mine is automatic, manual transmission cars don’t have that
Do you know the part for Honda Accord 2001 ex 3.0 L park/ neutral sensor ?
Standard Motor Products NS158 Neutral/Backup Switch www.amazon.com/dp/B000C81KBS/ref=cm_sw_r_cp_api_i_JlQbFbTG5QXQ8
Ty for the fast response . I appreciate it
Your welcome
I replaced mine but now my car won’t start. Any suggestions? Please help.
Did you get a new one or use? When you do this the car needs to be in neutral
@@BulletSolano I got a new one. bro thank you so much. I spent an hour or so messing with it yesterday giving myself headaches and I spent an hour or more this morning messing with it and I’m not sure what I did but it works now. Thanks again so much. I think it does have to be in neutral and you really have to be careful to line it up EXACTLY where it is supposed to be.
No problem
What’s the part name? I can’t find a transmission range sensor for my car.
Standard Motor Products NS-156 Neutral Safety Switch www.amazon.com/dp/B00ATCF8U6/ref=cm_sw_r_cp_api_i_.RaPCbRE0A1H9
So if I have one from say a junkyard, I'd do this swap in park?
Yes just to make sure is on park
@@BulletSolano so the part from the junkyard make sure is on park and make sure that my car is also on park?
No, make sure both are on neutral
So the sensor is the whole part or just what’s inside it ?
The whole part
Bullet Solano Thankyou so much
Would that also be the same peoblem for p0705?
Yes
Thx u
No problem
My 99 Honda Accord shifts hard at 20 mph and there is no transmission code, all I did was change the tps
Throttle position sensor?
TPS has noting to do with the transmission, but when you change the throttle position sensor is really difficult to put it in the same place, that’s why I never mess with it, my suggestion is to get a use throttle body from the junk yard put it on and see if that helps
Is this the same on 98 civic do the parts look the same
Almost
Is a Saturn 2006 tms located in the same place
Should be
Mira yo saque el mio y lo limpie pero estaba en park y asi mismo lo volvi a poner pero pero no me ilumina cuando lo muevo a d4 las demas si se iluminan qe puede ser?
Se movió, ponlo en neutral después quítalo el sensor y ábrelo y mira que esté en medio si no está en medio ponlo ahí y pon todo pa tras pero deja el auto en neutral
@@BulletSolano ok eso voy a hacer gracias por tu ayuda ,
Listo
So if it’s used your car can be on PARK
Yes, if you not sure open the sensor to make sure, and put the little part in the middle
after a transmission replacement on 2006 honda crv i was getting a P0706. I replaced the transmission range sensor but now the car is cranking but isn't starting. I tried to use starter fluid to start car and it didnt start so i suspected an ignition problem and none of the coils will produce a spark when putting another spark plug. did i mess something up with the transmission range sensor? I tried to follow everything by the video. please any advice?
and the check engine light went away after that why i didnt assume it was the sensor still. currently no check engine lights
I don’t think you did something wrong with the transmission range sensor, but when you did the installation the car was in neutral? If so just check the 3 main things air, spark and fuel
@@BulletSolano yeah i made sure it was in neutral. And i have no spark. There isnt a check engine light. The car not starting bcus there isnt spark but idk what exactly the problem is. What would you do?
Check the distributor
Im not sure but i got code P1706 for 98 honda accord
does this work for acura tl 2002?
Yes is the same process
I have the same issue, but when driving the code goes away on the scanner any suggestions. Thank
When you driving the transmission fluid level gets high probably that’s why the code goes away, check the transmission fluid level and connections of the sensor, also if you have that code the sensor probably is bad anyways
Bullet Solano Perfect, thanks a million
No problem bud
Bullet Solano gd evening is the code P0705 related to the P0706? Same part?
Hi, yes is the same
but why you did that ? only for show to us how to do that cuz you just take it off , opened it and installed again ?
Watch the video
#bullet solano, donde puedo comprar el sensor? Solo el sensor necesito o toda la parte?
Si lo compras en una tienda de auto servicios es caro pero si puedes hazlo, si no en un deshuesadero
Bullet Solano llame al dealer de la honda y cuesta más de 300 dólares... y en las tiendas de auto Partes cuesta mas de 100... en los deshuesaderos no se si encuentre alguno. Muchas gracias bullet solano
El el deshiesadero yo encontré el que tengo en el auto, por suerte me salió bueno, checa ahí por que ahí si lo encuentras
Bullet Solano voy a ver si lo encuntro en el deshuesadero local. Muchas gracias bro.
Saludos. Y buen vídeo.
Listo bro cuídate
Just changed mine out , get a code P0705, what you think it is? I double checked my work. Everything good.
Probably the one you’re get is bad
@@BulletSolano thank you... thanx for replying at a timely matter.. Iv changed it to the old one before I did I cleaned it out but still the same code.
Ok bro get a new one
@@BulletSolano so I was getting tired of the issue so I changed it out One more time ,I opened the New one realized it wasn't on neutral closed it back up , installed it and no more p0705. Lol
Nice bro
Like
good friend greetings I have code 5 in D4 that will be that failure
D4 is blinking?
@@BulletSolano
if it is flashing and I scan it with jumper and it flashes or flashes 5 times the D4
@@BulletSolano
the box is recently repaired they changed everything and from before it was the same with code 5 in D4
@@BulletSolano
but I don't know what that code will be because I bypass it and scan from the board and it blinks 5 times. D4 is the only code that it is giving me.
Replace the pressure switch and adjust the Anand B solenoids
Haz el vídeo en español papi, desde aquí se escucha que hablas español
th-cam.com/video/EnREKipWJqM/w-d-xo.html
why does no one have the V6???
Too many moving parts, and no space to work on!!
@@BulletSolano i just want to know where the number is for the transmission , i have the motor number " J30A1 2104906 " but can not locate the transmission tag or number
Automatic?
The number of the transmission is on a label on top of the transmission
@@BulletSolano yup automatic sorry took a while to reply
Why you changed the shift on neutral
Because that’s the setting point for it, when you get a new one is set in neutral
Hello, i’m hoping you can help my husband and I. He replaced the transmission range sensor to our 2007 Honda Odyssey. After changing it, the gears for drive and neutral will no longer light up, but the others do. It’s still shifting, but not sure what happened with those specific gears no longer lighting up.
Hi, when replacing ir the vehicle was in neutral?
Hello, yes, it was in neutral when changed.
Honda Civic 2001 automatic transmission in my vehicle and the address given in the video as I do flare.
th-cam.com/video/G35Irz1Cno4/w-d-xo.html
please help me. The transmission oil has changed the problem continues.