That’s not how you change the license plate bulbs. It shows you in your owners manual how to take them off from the outside. Essentially just look for the side of each housing that has >pc< printed on it, put a finger on that side and push sideways. You will feel it move and then you just pull out. Also do not use a pry tool on the puddle door light, there is a slot designed for a medium size flat screwdriver that works much better.
Just received mine today. Went with you guys because of the professional presentation and tools provided. I was leary of getting the $22 set off of Amazon. Took 10 minutes to install all interior lights. Big improvement especially trunk and door lights. Thanks!
Thank you so much for choosing PrecisionLED! We really appreciate the positive feedback, it is always nice to hear that our hard work pays off in making installation for our customers quick and simple. Enjoy your superior interior lighting!
Replaced my Forester's bulbs with white LEDs, and for the licnese plates, there is no need to pry out the interiors. You can do it from the housing outside. Mine is a '14 though, just not sure for the following ones. Good video though.
@@georgemaniatis4673 I used the tool and went from the outside to pry the casing off. I think it was a youtube video I came across. Not sure if this helps or not but it can be done. Found out it is illegal here in VA so I had to put the OEM lights back. Kinda sucks.
If I could add to an already great video, after putting my bulbs into to assemblies on bottoms of doors and in cargo area, before snapping them back into place I put some foil tape (used for ductwork) as a "backer reflector" overtop the backend of the assembly before snapping them into place figuring no use some of the light being lost illuminating the insides of door panels or behind cargo light. I believe now the light is reflecting better outward through the lens of the assemblies.
Great video. I’m replacing a taillight assembly so I figured I’d start replacing all/ or most of my bulbs. You did a great job of thoroughly covering the procedures. Thank you for a very helpful video. - Mark in PA
Changed out all the interior bulbs but the map lights. I've discovered (for us) that LED's are just too bright to be functional, when they're that close to our eyes. The OEM bulbs are easier on the retinas!🙂
After replacing all interior lights with LED ones for my 2015 Forester, DTC B2282 occurred. “Keyless access with push-button start system needs to be checked”
Great info. One question: What about the courtesy map lights directly above the back passenger and driver side doors? They’re push lights directly above the rear/side windows.
Hello Phil, my Forester XT 2017 is coming in about 1 month time, and I intend to change out all the interior lights to LED white lights. I hope you can give me some advice on what are parts I will need. I saw your video, I think its easy and I like to try the change out on my own. I also like to change the fog light as well, can you help list out what are the choices I can pick from your web. Appreciate it a lot :)
Hi Wilson, sorry for the late response, we hope you were able to find the LEDs you need using the links in the description box below the video! Please feel free to reach out at help@precisionled.com for any specific questions and we will be able to assist you further!
My subaru is a 2013 and I bought a basic light package (I think these were fog lights?) and I’m not sure if they fit right and I fear I might have an SH body. Any tips? @PrecisionLED
Here is the proper kit for your Outback fogs: www.precisionled.com/premium-9006-cree-led-headlights.html Also, we back our LEDs with a lifetime warranty.
You would have to add them to your cart separately. Here is a direct product link: www.precisionled.com/subaru-forester-led-backup-reverse-lights-2009-present.html
Hi! Here is a link to the 3rd gen Forester interior kit: precisionled.com/subaru-forester-premium-led-interior-package-2009-2013.html The trunk light would be a T10 which you can find here: precisionled.com/premium-t10-canbus-6smd-5730-led.html
Yes, that is correct, the installation process would be very similar, if not identical to the video shown. Also, the linked products in the description will be compatible with your 2018 Forester.
What item did you use to change out the reverse light bulbs? I have a 2018 FXT I am trying to change. Do your company offer LED Fog lights? I believe H11?
The T10 bulb fitment was used for the reverse lights, which you can find here: www.precisionled.com/premium-t10-canbus-10smd-5730-led.html Also, yes, here is the correct H11 fitment for your fogs: www.precisionled.com/premium-h11-21-smd-5730-led.html Please note, the linked product is for a single LED bulb, and you would have to adjust the quantity of the LED to 2.
We have listed your transactions were declined because the billing address input during checkout does not match the billing address of the credit card. If you continue to have issues, feel free to reach out via phone.
![BOWKYLION - วิงวอน (ex-change) [Official MV]](http://i.ytimg.com/vi/cLdnZWDaO-w/mqdefault.jpg)
That’s not how you change the license plate bulbs. It shows you in your owners manual how to take them off from the outside. Essentially just look for the side of each housing that has >pc< printed on it, put a finger on that side and push sideways. You will feel it move and then you just pull out. Also do not use a pry tool on the puddle door light, there is a slot designed for a medium size flat screwdriver that works much better.
Thanks for the advice!
Thorough, Clear, and Accurate. This is truly an exceptional installation video.
Thanks for tuning in!
Just received mine today. Went with you guys because of the professional presentation and tools provided. I was leary of getting the $22 set off of Amazon. Took 10 minutes to install all interior lights. Big improvement especially trunk and door lights. Thanks!
Thank you so much for choosing PrecisionLED! We really appreciate the positive feedback, it is always nice to hear that our hard work pays off in making installation for our customers quick and simple. Enjoy your superior interior lighting!
Replaced my Forester's bulbs with white LEDs, and for the licnese plates, there is no need to pry out the interiors. You can do it from the housing outside. Mine is a '14 though, just not sure for the following ones. Good video though.
MatthewPT Correct I got 2016(asia model) no need to take out the interior you can access the license light from its casing
I have a 2018 and I did it from the casing as well.
Thank you for the advice!
@@severindicroce , hi. Can you explain how to remove the casing? I'm about to do an upgrade too, but don't want to pull out the lining.
@@georgemaniatis4673 I used the tool and went from the outside to pry the casing off. I think it was a youtube video I came across. Not sure if this helps or not but it can be done. Found out it is illegal here in VA so I had to put the OEM lights back. Kinda sucks.
If I could add to an already great video, after putting my bulbs into to assemblies on bottoms of doors and in cargo area, before snapping them back into place I put some foil tape (used for ductwork) as a "backer reflector" overtop the backend of the assembly before snapping them into place figuring no use some of the light being lost illuminating the insides of door panels or behind cargo light. I believe now the light is reflecting better outward through the lens of the assemblies.
Great video. I’m replacing a taillight assembly so I figured I’d start replacing all/ or most of my bulbs. You did a great job of thoroughly covering the procedures. Thank you for a very helpful video. - Mark in PA
Thank you for the positive feedback!
Changed out all the interior bulbs but the map lights. I've discovered (for us) that LED's are just too bright to be functional, when they're that close to our eyes. The OEM bulbs are easier on the retinas!🙂
Great video. Going to order my set of lights now. Thanks
Hi, did you go for STANDARD OR PREMIUMS ???..I'm wondering if the PREMIUMS are too bright
Thanks for watching the video!
Thank you for sharing just got 2015 going to up date the lights with led
Nice! Let us know if you need any help with the install.
After replacing all interior lights with LED ones for my 2015 Forester, DTC B2282 occurred. “Keyless access with push-button start system needs to be checked”
Is the small access cover plate on the hatch cover removable with trim tools, without removing the large cover?
Hi Good day. do you have list of bulb types for every socket for forester? thanks
Felicitaciones!! Nunca había visto un video tan completo. Muchas gracias.
Great info. One question: What about the courtesy map lights directly above the back passenger and driver side doors? They’re push lights directly above the rear/side windows.
Disregard my mistake
No worries, thanks for tuning in! Let us know if you have any other questions.
Very well detailed thank you
Hello Phil, my Forester XT 2017 is coming in about 1 month time, and I intend to change out all the interior lights to LED white lights. I hope you can give me some advice on what are parts I will need. I saw your video, I think its easy and I like to try the change out on my own.
I also like to change the fog light as well, can you help list out what are the choices I can pick from your web.
Appreciate it a lot :)
Hi Wilson, sorry for the late response, we hope you were able to find the LEDs you need using the links in the description box below the video! Please feel free to reach out at help@precisionled.com for any specific questions and we will be able to assist you further!
mine is 2013 xt premium forester will this kit work on my car?
Well done!!!
Thanks for the support!
Thanks
compatible with 2019 Forrester Premium?
thanks! Great help!
Thanks for tuning in!
Any issues with them overheating?
Great video. Thanks!
Thanks for watching!
hey, great video, what about the headlights?
Here is the video for the Forester headlights: th-cam.com/video/Han9EC9SMQo/w-d-xo.html
Do they have a kit for the 2010 Impreza premium sedan?
We do! Here is a direct link: www.precisionled.com/subaru-impreza-premium-led-interior-package-2007-2011.html
Hey guy, have u replaced the break lights to LEDs?
No, we do not advertise upgrading break lights to LED as they would hyper flash when ignited.
*brake
@@SuperLordHawHaw yeah give me a break
My subaru is a 2013 and I bought a basic light package (I think these were fog lights?) and I’m not sure if they fit right and I fear I might have an SH body. Any tips? @PrecisionLED
Did you purchase your lights from us? If so, please feel free to reach out at help@precisionled.com!
job well done!
Thank you for the kind words!
Lookin for LED fogs for my 01 Subaru OB 2.5. and do you offer a warranty? Thanks
Here is the proper kit for your Outback fogs: www.precisionled.com/premium-9006-cree-led-headlights.html
Also, we back our LEDs with a lifetime warranty.
Is the backup reverse lights included in this package?
You would have to add them to your cart separately. Here is a direct product link: www.precisionled.com/subaru-forester-led-backup-reverse-lights-2009-present.html
Are these the 6000 crystal white or 8000 cool white leds?
Thank you for your interest. The 6000K color is used in the video.
Link for the reverse light bulb leds
Here is the correct reverse LED: www.precisionled.com/premium-t10-canbus-10smd-5730-led.html
Also, please, be sure to adjust the quantity to 2.
What about the third gen forester?
Specifically with the overhead trunk light?
Hi! Here is a link to the 3rd gen Forester interior kit:
precisionled.com/subaru-forester-premium-led-interior-package-2009-2013.html
The trunk light would be a T10 which you can find here:
precisionled.com/premium-t10-canbus-6smd-5730-led.html
Will these work for 2018 Forester premium ?
Yes, that is correct, the installation process would be very similar, if not identical to the video shown. Also, the linked products in the description will be compatible with your 2018 Forester.
What item did you use to change out the reverse light bulbs? I have a 2018 FXT I am trying to change. Do your company offer LED Fog lights? I believe H11?
The T10 bulb fitment was used for the reverse lights, which you can find here: www.precisionled.com/premium-t10-canbus-10smd-5730-led.html
Also, yes, here is the correct H11 fitment for your fogs:
www.precisionled.com/premium-h11-21-smd-5730-led.html
Please note, the linked product is for a single LED bulb, and you would have to adjust the quantity of the LED to 2.
This fused my X-ray interior lights and the key fob doesn’t work
Tried 2 good cards, transaction would not go through
We have listed your transactions were declined because the billing address input during checkout does not match the billing address of the credit card. If you continue to have issues, feel free to reach out via phone.
Hi Good day. do you have list of bulb types for every socket for forester? thanks