Amazing Tools Hardware | Not AI | It is Real Maintenance Tools and Good Repair Tools Top Videos
ฝัง
- เผยแพร่เมื่อ 22 มี.ค. 2024
- Amazing Tools Hardware | Not AI | It is Real Maintenance Tools and Good Repair Tools Top Videos #shorts
- แนวปฏิบัติและการใช้ชีวิต
You know its real when the bolt starts moving as soon as you drill into it😂
your gonna strip every screw you work with at that speed 😂
It sure does help to have the project so exposed and in the open, not needing to work upside down and backwards.
Этот винт легко можно было открутить простой отвёрткой, на крайний случай ударной. А тут видео ради видео. На таких маленьких винтах экстрактор не работает, если резьба прикипела, нужно сверлить глубоко и маленьким сверлом, чтоб не срезало шляпку винта. А тонкий экстрактор тупо сломается если резьба дейсвительно прикипела и высверлить экстрактор практически не возможно. В этом случае только греть и ударная отвёртка.
You know it might help more if you put the drill in reverse before you try take the screw out the first time
Just a note, before you attempt to remove a screw like this, hit it with some PB blaster a few times, let it soak for maybe 20 mins, often, screws like this will come out easy, if not these extractor bits are great
These extractors have been around for many years. If the fastener is stuck very tightly then the extractor will break off just as the torque reaches maximum force of the tool it.
They work great when the bolt is already loose!
Easy outs were a staple when I was an aircraft structural mechanic in the Air Force.
I've used a very sharp and wide punch and hit the side of the bolt to twist it counter clockwise also or weld a nut to the bolt 🔩
Есть одно но , при сверлении болтик уже крутился
Мужик, если это была подготовка - ок. Но если ты реально откручиваешь закисший болтик шуруповертом - ты еще тот дикрайдер.
Use the right screw driver the first time next time 😂
Good thing I always have my DeWalt Swiss Cheese in my tool box!
Странно, что выкручивал на низких оборотах, а не дал жару, как в начале.
Ive tried numerous bolt extractor sets and never have luck with em. Maybe for a low torqued one like this maybe.
По часовой стрелке закручивать, против раскручивать.
Spraying some lubricant on the screw and heating it can help loosen it out.
Можно было выкрутить обычной отверткой, а не усложнять себе жизнь
Just buy a new starter bro 😂
Can’t wait for the Funk FPV reaction.
There ya go 👍
Здравствуйте, на видео вам получается, а в натуре нет, дальше сверли давай! 😊
I used one of these yesterday. Works like a dream, but correct and careful preparation is essential.
The extractors had been sottong in my toolbox for years before yesterday. Good to have some on hand.
Судя по всему это втягивающее реле стартера. В автомобиле к нему дрелью не подлезть)
431k likes and 3 comments, seems legit.
So amazing that when you out the tool your wanting to work you backed the screw out in the correct direction. The Phillips head would have worked if you backed it out instead of trying to tighten it
They say use the right tool the first time ,get the job done quicker.
I have never once used an extractor successfully. They have always broken in 1/2 and we’ve had to drill it out anyway.
The screw was loose already, they pre-stripped it out. You can see the head wiggle when they're drilling it
Maybe do not use a drill next time? 💀
Maybe if they would have started backing it out instead of tightening it, it would have worked the first time.
Didnt think this was AI, but how many times you say its not AI, I am starting to believe its AI.
So nobody going to mention u can see the screw start to tighten when he started drilling it meaning its already loose and likely been taken off and screwed back on lightly to make it look like the tool worked as advertised
Something cool I learned. I was disassembling a lg condenser unit and had stripped two small Phillips screws on backside of electrical box. I didn't have my extractor set so I took a self tapping screw and drilled it in reverse and it worked!! Probably not effective on every stripped out screw but it actually worked for me that day!
.
I
Thanks for reminding me of how to use them. 😊
You’re welcome 😊
Easier way. Don't use power tools. Bit of CRC and use a screwdriver. Problem solved
Its called an easy out. Been around for a hundred years. Great tool
It's always good to have an extraction kit.
The bolt started moving as soon as you started drilling. Meaning your drill bit is to blame. It wasn't even tight buddy
The bolt was already loose 😂😂you can see how it tightens a bit when it is drilled 😅😅
Drill: *cutely shreds up screw*
Create a problem ❌
Buy a solution ✅
It's called a screw extractor. They've been around forever. Nothing "amazing" about it.
Kaha se milega kis name se aata he ye
"not AI." As if this is some Star Trak technology. 😂
Philips head screws should be illegal.
Yes, lets start off max torque on a rusted screw in the starter.
It moved when you first put the drill bit on it. Lord man
When dumb people try to sell you their tools
What happens when the easy out breaks off inside the screw? Maybe use a vise grip to remove it?
That fastener was already loose it was moving just from drilling it!
That's what a Z4's convertible pump looks like.
I can't believe the paper didn't work...
the sound that made my ears bleed was the best part
А можно обработать заранее wd 40,и простучать через отвёртку, край делов погреть и всё получится
Next time try loosening it at first instead of tightening it
They are called left handed drill bits. Look them up. They help in a lot of situations
Is it just me or did the screw move when mans drilled a hole in it?
The fact that you had to put “not ai” is sad
Why on earth would you go so fast on the initial unscrew attempt? Sometimes slow is fast...... Look at all the work you created to solve your mistake.
Thanks for this, now I can fix my blender.
The small one was already stripped out. 😆
I've bought multiple brands of those and they never work.. I just hammer a torx screw into the stripped one.. Comes out everytime
Jeez that’s awesome I’ve never seen an ez out. Before , I thought you were gonna weld a bolt to it
Looks like that bolt was loose when he drilled
Bro, you need some 5000 rpm at least😂😂😂
Or you just use the correct fitting Phillips head to begin with. Usually help.
I like the part where you do it the wrong way and ruin the screw so you can show off your product if you do things the right way the first time you don’t need this product
It is called an easy-out !!
Its not tight you can see the bolt move when he drills it 😂
Trust me, nobody fucking thought this was AI
I would have just left the screw on and replace the whole thing.
In America they are called “easy outs”
Why not try spraying something like a WD40 before doing this ?
i’ve gotten those things to work exactly 1 time in my life. maybe the lowe’s brand isn’t so hot
I just had a mechanic that got a broken seized bolt that was causing my truck to leak antifreeze
I don’t like those extractor kits. I just grab my grinder cut a slot in screw head and use a flathead screwdriver to unscrew it.
At that point just buy a new starter
Stripped before you started 😂
I saw it turn with the drill bit 😂
Bolt extractor have had one of those in my tools set since the early 80s.
I wonder how you take it off after that 😅
Bruh. 😂 if you can turn the tap slow enough to make it work, you can turn that screw out slow without stripping it. This was dumb af.😂
I needed this tool to work for me 3 times , never did , waste of money unless you are dealing with glasses screws
Very helpful. Thank you.
Put the drill away and use a screwdriver . Shock it by tapping it on the end. Bingo
You wouldn't need an extractor if you did it right to begin with. Weird
Probably could of got it with one of them fingernails 😂
Not even your grandma believe that
I had the same problem yesterday.
Now how to remove screw from the device😅
Lucky him, I've never had much success with easyouts & I'm a professional
Do this on a hardened steel screw head.
Why is this on TH-cam... this is ancient history
WD40 uygulasan bu kadar uğraşmaya gerek kalmazdı
Would love a link for the set
how does this have nearly half a million likes but only 3 comments
Just me or the screw bit going going wrong direction
Is that sandpaper he drills in? And wouldnt it just disentigrate after you redrill???
Про ударную отвёртку забыли что ли?