Great job! Extraordinary filming so clear and well positioned camera for all aspects of dismantling and reassembly. All your videos are like this its a pleasure to watch
Its 8-30 in the morning, am having a coffee, and watching my favourite "technician" at work, being able to hear the mechanical sounds and no voice overs make it therapeutic to watch. Why do I look forward to them...............................maybe its the excellent camera angles.
Thank you so much for this video, it gave me the confidence to get it fixed myself. Although by some errors it took me near 15 hours all in all, i got it done. Thx a million !
Hey Kevin-Albert. Thank you for this great video. I was looking at the technical paper of the C1 and the steps described there are much complicated as yours. So I was about to give up doing it myself until I see your video. One question: what kind of clutch centering tool are you using (which diameter for the C1)? Will the KS Tools 150.2180 fit for this? Thank you!
Just like to thank you for a great job on my Citroen C1,turned up on time, traveled a fair distance to get to me and 4 hours later job done, many thanks would highly recommend Kevin.
Brilliant and very clear video without missing any procedures. Also a very calm and careful mechanic. I am planning to replace the clutch assembly on Citron C2 Design 1.1 L 2006. Unable to select gears when the engine is on and the clutch pedal goes to the floor and stays there. Questions: Will this video apply for C2 and if not what are the extra steps and do you also have to take the driveshaft hub nut on C2. I do not want to do that as I do not have a big torque range. Which clutch assembly is best Valeo or LUK? What red grease did you use and why did you apply to the bolt holes? What grade oil, semi-synthetic or fully synthetic, and how much do I need for C2? Did you change the position of the jack under the engine sump and why? What is the torque for the clutch plate to the flywheel? Do you fill oil until it just starts dripping from the filler hole? Roughly how high to jack the car? Don’t have to remove the battery and clear that area in C2?
It’s almost identical to this C1. Gearbox oil MTF 75w90 20nm for pressure plate bolts. But give it a little extra just to be safe. I never Jack the engine up from the sump. Secure gearbox with axle stand and move jack under gearbox. You’ll need roughly 2.5L of oil. You should be ok on the 3rd hole of an axle stand. Engine is Roughly about 3/4m off the floor
@@WMCS Thanks for the prompt response. So just for clarification, on C2 I definitely do not have to remove the driveshafts? Just remove the lower ball joints from the wishbone and slide the driveshaft out? Also which clutch kit do you recommend or fit? On your C1 video, I thought you jacked the engine up the sump? What grease did you use? On C1 you did not have the axle stand under the gearbox but I will do that. I believe you have to also remove the battery area to gain access to the gearbox mounting. On C1 you did not remove the battery area. I want to avoid extra work if it is different from C1. Have got a video for a clutch replacement for C2 and is C2 the same as C2?
Great job Kevin , I hate those stupid starter rubbers , fall off nearly every time , I usually undo the front pipe to miss the lambda sensor , and I use a 2 poster 😎👍👍💯🇬🇧😷
It was a very very close one to the lambda sensor. I had to put a little bit of rubber sealant to hold that little plastic guide for the starter. You’re right it keeps falling off
Managed to remove and replace the clutch on C2 2006 manual. During the refit, there is one safety pin that fits to one of the electrical block connecteor behind the battery. I can remember where and how another pin fits to an electric connecter nears the slave cylinder. Please advice. Also, the clutch feels very spongy and I have to bleed it many times and it is still the same, any advice. Thanks
thanks, yes I can select gears when the engine is running. I have also driven the car without any issue, but the bitting of the clutch is low. I am planning to bleed it again. I think the problem is that when I removed the slave cylinder, the plunger might have come out as there was lots of fluid in the rubber boot. So the air must have gone in. In the video, you make it so easy and have all the trade tricks. Also, do you know where does the pin fits on the electric connection?
Hi, I have managed to remove the gearbox and have replaced a new thrust sleeve on the shaft and new clutch assembly with Draper alignment tools. I do not have a crane host, working with floor jacks. I am not a strong as your mechanic and having extreme difficulty replacing the gearbox to the engine. I am lifting the gearbox with rope. Is there a technique to push the gearbox shaft into the engine?
@@WMCS Hi managed to get the gearbox in after struggle for a couple of hours. The only problem was when I tried to fit the slave cylinder it was very difficult and was not able to move the clutch lever. Took the rubber dust cover off the gearbox and found the lever has come off the pivot. I must have pushed the lever when pushing the gearbox into the engine. Now I have to remove the gearbox back and sort the lever out. Very disappointed. I also find some fluid was leaking from the slave cylinder when I tried to push it into the lever. Have got a video on how to replace a slave cylinder and bleed. I can find a video anywhere. thanks for your help.
great _howto_ *but* there are some steps missing...I dismounted my gearbox today for the replacement of the gearbox itself and I came across with some issues, maybe it's because I'm a self taught guy. Thank you for sharing
Adoro ascoltare il rumore ed il ticchettio degli attrezzi .... è molto rilassante...I love listening to the noise and the clicking of tools ... it's relaxing
Just wondering chum how many clutches do you install in a day? Its hard graft... Any time i do a clutch ive to rest the next day exhausted.. Next question have u ever done a clutch/flywheel on a kia sportage 2.0crdi 2010 onwards?
I'm a mechanic and with a crane, it's hard to let alone a car like this, it's easy to work but some heavy work I've done a few times like this and it's not easy at all.
Hiya, absolutely love your vids, helped me sort my clutch the first time. Doing it again and would like to ask, what is the metally fluffy thing that you put on the bolts for the gear linkage panel? Is this some sort of material to reduce vibrations? Also any tips to stop the clutch adjuster knob becoming loose? I had to keep tightening it like once a week with my old clutch. Thanks again. :) :)
Legendry Kevin, top notch and straight to the point. Can you at some time show us how yo do the MMT auto box on the Aygo, 107 or C1. I understand the MMT needs retracting pre change and calibrating post replacement. Blue point have a technical bulletin on how to do this manually without OBD. Keep up the brilliant work 👏
@@WMCS SO yesterday i changes the clutch on my C1 and your video helped a lot. Was easy to follow. We had some problems with the driveshaft as the wishbone didnt want to come out as easily as in your video. We just removed the bolt that connects it to the car which enables you to swing it out and that kind of worked. Also we had to remove the Gearbox holder on the gearbox to get more clearance. After doing it i just cant express how much respect i have for your work. Just lifting the gearbox out and in ist just so hard and you are doing it alone. Much respect and i glad that you helped us that much with your video! Thank you!
The best mechanic in UK ! Thanks for sharing ! Respect man !
The Best!!!
Maybe best fitter ;)
Wow! Car mechanics are really vehicle surgeons . So clever and skilled, amazing video.
Great job! Extraordinary filming so clear and well positioned camera for all aspects of dismantling and reassembly. All your videos are like this its a pleasure to watch
Its 8-30 in the morning, am having a coffee, and watching my favourite "technician" at work, being able to hear the mechanical sounds and no voice overs make it therapeutic to watch. Why do I look forward to them...............................maybe its the excellent camera angles.
instaBlaster...
Thank you so much for this video, it gave me the confidence to get it fixed myself. Although by some errors it took me near 15 hours all in all, i got it done. Thx a million !
15 hours not bad as long as the end result was a good one. ✨🍻
Great job but quiet dangerous. If you had a helper guy it would be much easier. Safety first.
How you doing fella? Hope work hasn't slowed down to much for you. Keep up the good work. Great video.
Hey Kevin-Albert.
Thank you for this great video. I was looking at the technical paper of the C1 and the steps described there are much complicated as yours. So I was about to give up doing it myself until I see your video. One question: what kind of clutch centering tool are you using (which diameter for the C1)? Will the KS Tools 150.2180 fit for this? Thank you!
Clutch alignment tool. It comes with different size attachments
Hello there. Great vid. Looking forward to see a Nissan Micra k12 2005 video soon hopefully!
I noticed you don"t lubricate the throw out bearing sliding surface. Is that to prevent clutch dust buildup gumming up the sliding surface?
That’s right. Otherwise it will gum up and will start sticking ✨🎄🍺
you know very good compliments 😀👍
Just like to thank you for a great job on my Citroen C1,turned up on time, traveled a fair distance to get to me and 4 hours later job done, many thanks would highly recommend Kevin.
Hello brother Good job 😁😁👍
Just dumped gearbox oil all over my drive when removing the drive shafts...must have missed the bit in the video where it was drained out...
Brilliant and very clear video without missing any procedures. Also a very calm and careful mechanic.
I am planning to replace the clutch assembly on Citron C2 Design 1.1 L 2006. Unable to select gears when the engine is on and the clutch pedal goes to the floor and stays there.
Questions:
Will this video apply for C2 and if not what are the extra steps and do you also have to take the driveshaft hub nut on C2. I do not want to do that as I do not have a big torque range.
Which clutch assembly is best Valeo or LUK?
What red grease did you use and why did you apply to the bolt holes?
What grade oil, semi-synthetic or fully synthetic, and how much do I need for C2?
Did you change the position of the jack under the engine sump and why?
What is the torque for the clutch plate to the flywheel?
Do you fill oil until it just starts dripping from the filler hole?
Roughly how high to jack the car?
Don’t have to remove the battery and clear that area in C2?
It’s almost identical to this C1.
Gearbox oil MTF 75w90
20nm for pressure plate bolts. But give it a little extra just to be safe.
I never Jack the engine up from the sump. Secure gearbox with axle stand and move jack under gearbox.
You’ll need roughly 2.5L of oil.
You should be ok on the 3rd hole of an axle stand. Engine is Roughly about 3/4m off the floor
@@WMCS Thanks for the prompt response. So just for clarification, on C2 I definitely do not have to remove the driveshafts? Just remove the lower ball joints from the wishbone and slide the driveshaft out? Also which clutch kit do you recommend or fit? On your C1 video, I thought you jacked the engine up the sump? What grease did you use? On C1 you did not have the axle stand under the gearbox but I will do that.
I believe you have to also remove the battery area to gain access to the gearbox mounting. On C1 you did not remove the battery area. I want to avoid extra work if it is different from C1. Have got a video for a clutch replacement for C2 and is C2 the same as C2?
hi whats the liquid you are spraying? iam planning on doing my wife car toyota aygo. your video is a great help for us beginners
It’s brake cleaner.
Complimenti hai fatto il miglior video tutorial sul cambio frizione.... 👍 👍 👍 Complimenti veramente bravissimo..
Always good job 👍👍👍👍👍👍👍👍
Great job Kevin , I hate those stupid starter rubbers , fall off nearly every time , I usually undo the front pipe to miss the lambda sensor , and I use a 2 poster 😎👍👍💯🇬🇧😷
It was a very very close one to the lambda sensor. I had to put a little bit of rubber sealant to hold that little plastic guide for the starter. You’re right it keeps falling off
saved to watch AM :)
Excellent travail.
J avais peur pour la sonde lambda.....mais nickel!,
I'm looking out for the VW Up video ...but might have to wait a few years as they are not that old.
Neither are MK2 Aygo but I just had mine done by Kevin
Good job mate
What’s the price you charge mate fitted do you cover Rutland area? East Midlands
www.williamsmobileclutch.co.uk
Managed to remove and replace the clutch on C2 2006 manual. During the refit, there is one safety pin that fits to one of the electrical block connecteor behind the battery. I can remember where and how another pin fits to an electric connecter nears the slave cylinder. Please advice. Also, the clutch feels very spongy and I have to bleed it many times and it is still the same, any advice. Thanks
Can you select gears with the Enugu engine running
thanks, yes I can select gears when the engine is running. I have also driven the car without any issue, but the bitting of the clutch is low. I am planning to bleed it again. I think the problem is that when I removed the slave cylinder, the plunger might have come out as there was lots of fluid in the rubber boot. So the air must have gone in. In the video, you make it so easy and have all the trade tricks. Also, do you know where does the pin fits on the electric connection?
Hi what's the name off the bit that go's on the end off ratchet
Hi, I have managed to remove the gearbox and have replaced a new thrust sleeve on the shaft and new clutch assembly with Draper alignment tools. I do not have a crane host, working with floor jacks. I am not a strong as your mechanic and having extreme difficulty replacing the gearbox to the engine. I am lifting the gearbox with rope. Is there a technique to push the gearbox shaft into the engine?
Just a bit of a wiggle. And keep it straight. It should go in nicely
@@WMCS Hi managed to get the gearbox in after struggle for a couple of hours. The only problem was when I tried to fit the slave cylinder it was very difficult and was not able to move the clutch lever. Took the rubber dust cover off the gearbox and found the lever has come off the pivot. I must have pushed the lever when pushing the gearbox into the engine. Now I have to remove the gearbox back and sort the lever out. Very disappointed. I also find some fluid was leaking from the slave cylinder when I tried to push it into the lever. Have got a video on how to replace a slave cylinder and bleed. I can find a video anywhere. thanks for your help.
you make fitting the box back on look easy
It’s not that bad .. , but saying that it has to be a one time lift. Can’t have it dangling above me for too long. A bit heavy.
👏👏👏clutches warrior, it seems so Easy !
Great mechanic, nice filming with eye for detail!
great _howto_ *but* there are some steps missing...I dismounted my gearbox today for the replacement of the gearbox itself and I came across with some issues, maybe it's because I'm a self taught guy.
Thank you for sharing
Very amazing video so cool, I just follow it step by step and the clutch on my véhicule is now changed thank you very much
Amazing. Can you fix my aygo mmt clutch haha. Watching to see if I could but I think I’d screw it up as I’m not a mechanic 😞
Exactly what he same. Except you have to disengage the mmt module. It can be done manually. Then re sequencing it after replacement clutch.
Kevin-Albert Williams So it’s just exactly like this apart from clamping and resetting the actuator? No extra bits get removed not shown here?
Adoro ascoltare il rumore ed il ticchettio degli attrezzi .... è molto rilassante...I love listening to the noise and the clicking of tools ... it's relaxing
Glad it’s working both as therapeutic noise and good watching 🤩😆....
Question i ordered the clutch set for my citroen c1 from 2006, how much is a normal price for a mechanic to ask for the replacement work?
Saludos kevin deke pais eres buenos videos
Just wondering chum how many clutches do you install in a day? Its hard graft... Any time i do a clutch ive to rest the next day exhausted.. Next question have u ever done a clutch/flywheel on a kia sportage 2.0crdi 2010 onwards?
During the bolting of the pressure plate, the engine/flywheel turned clockwise, would this cause any issue, and what checks do I have to do?
Hi Monty as long as it didn’t continuously rotate clockwise you should be fine. The tensioner on the timing should keep the belt firmly on.
@@WMCS: thanks for the prompt response. It only turned less than half a turn or no more than one turn.
thanks for the prompt response. It only turned less than half a turn or no more than one turn.
I will change the gearbox by yours tutorial. Just great, thanks.
How was the shifting after word's? Did it improof?
Morning! Better shifting like old times? that fijn no need to change the gearbox!?
he did not add enough gearbox oil when finishing his job. That gearbox needs at least 1.4 litres.
...all ok but very bad whitening of pressure plate !!!!
What torque settings did you use..for everything?TAF?
You don’t ask for much do you ✨🍻🍻
@@WMCS cheers lol
Excellent demonstration thanks very much.
Thanks for this video really helped me with replacing sister in law's clutch 👌👌🤘
I'm a mechanic and with a crane, it's hard to let alone a car like this, it's easy to work but some heavy work I've done a few times like this and it's not easy at all.
nice 👍
Great step by step...
Dana 44 in a citroen ?
Hiya, absolutely love your vids, helped me sort my clutch the first time. Doing it again and would like to ask, what is the metally fluffy thing that you put on the bolts for the gear linkage panel? Is this some sort of material to reduce vibrations? Also any tips to stop the clutch adjuster knob becoming loose? I had to keep tightening it like once a week with my old clutch. Thanks again. :) :)
I think the fluffy thing was just used to keep the nut from falling out of the socket whilst traveling to the hole?
very good work.
Very good upload and gives me the confidence to know i could get away with this myself. Very detailed and steady
Hi ya. Whats the red grease? Great video.
Red rubber grease.
It's so good I will try it myself. Many thamks
Hi Kevin, brilliant video. Would replacing the clutch on a 1.0 toyota iq be virtually the same? I think its the same engine. Cheers.
IQ is completely different. I’ll try and shoot a video for one.
But you can see in the weekly videos. There a few of them
salutation de belgique. grace a toi j ai changé mon embrayage. un grand merci a toi.
Can it be more easier? Do try some renault or opel and more tuff old volvos
👍🏼👍🏼👍🏼Bravo
Excellent travail.Aucun commentaires verbales,donc adapté pour tous pays.
Exactement… merci beaucoup
@@WMCSBonjour. Est ce bien une intervention sur une C1 boîte automatique ? Cordialement
21:26 “what torque spec do you use?”
Him: “Yes”
Yes.
Sr william muy buen trabajos saludo
🍺🍺🎄✨
Really impressive video 👍🏻 I have a C1 (2010)
Thankyou. Really appreciate the feedback
How much do you charge mate?
36:16 if I filled up the oil but from that other way would that be ok ?
Yep
Legendry Kevin, top notch and straight to the point. Can you at some time show us how yo do the MMT auto box on the Aygo, 107 or C1.
I understand the MMT needs retracting pre change and calibrating post replacement. Blue point have a technical bulletin on how to do this manually without OBD.
Keep up the brilliant work 👏
Hi, so with these MMT auto box's unlike a proper torque convertor auto can you tow start them if the battery was flat?
Hi, i have a 2014 Toyota Aygo auto do you know if the manual clutch kit is the same thanks?
the front wheel bearing is Broken？
very good work
Thankyou.
Nice Video doing it after your video on the weekend. Is it possible to do it without the clutch centering by eyeballing it or using a broomstick?
Yes. You can eyeball it. As long as it’s fairly central.
@@WMCS SO yesterday i changes the clutch on my C1 and your video helped a lot. Was easy to follow. We had some problems with the driveshaft as the wishbone didnt want to come out as easily as in your video. We just removed the bolt that connects it to the car which enables you to swing it out and that kind of worked. Also we had to remove the Gearbox holder on the gearbox to get more clearance. After doing it i just cant express how much respect i have for your work. Just lifting the gearbox out and in ist just so hard and you are doing it alone. Much respect and i glad that you helped us that much with your video! Thank you!
Hi, Where do you jack the engine back up from where the gearbox meets the engine or the sump ?
Hi Kelvin you are amazing. You are number.one To more wonderful work .
To drop inside the sump. To jack back up always underneath the gearbox.
Do you remember how many km this car had ..?? and its first clutch replacement ? Thank you!
60k miles according to online, by the look of the existing release bearing that looks like the updated version so already replaced .
@@jusb1066 👍😉
Super ❤️
best mechanic ever
How long should it take
As long as it takes 🍻😁
Good job👍
Спасибо, это полезно!
how many Nm does the impact wrench have?
1000nm
just brilliant!
🍻🍻☀️
Great video, what did you use to clean in gearbox and clutch? Brake cleaner?
Yes it was brake cleaner. ✨✨
👍
May i know what is in the spray you clean up the flywheel, gearbox ?
Brake cleaner will do its job