For those who make comment about Language, first your brain is multifunctioning and can not think out of the box. Although, I do not understand his language, but instructions and how to make it is very clear.. So, if you have a little knowledge or can functionilise your vision then easy to understand. So, be smart before make any negative comment / So, Thank you my friend for an easy and simple Video to explain it. Great work keep up and I subscribe your channel. ( I am engineer but explanation visually very simple great work )
No mask and no gloves? You should consider using gloves as uncured epoxy has been linked to fertility problems. You also need a barrier mask or respirator as the epoxy dust and especially the inhaled airborne carbon fibers from sanding are damaging to your lungs. Carbon fiber dust is nearly impossible to exhale or cough out of your lungs. If inhaled it will become imbedded and form scar tissue causing reduced lung function over time. A thicker Mylar sheet of plastic will help to smooth out the wrinkles in the finished surface of the wing. The simple use of the PVC pipe as a roller is very clever, I learned something new and I’ve been doing this for 35 years. Nice clear video showing the basics of the process. Thank You
Great work. Here's a tip to improve the process; Once you have applied the cloth and resin, wrap in peel ply and then insert it in a storage vacuum bag and pull the vacuum. This will apply maximum pressure and also draw out excess resin into the peel ply. Leave until resin has set.
Hello I was blown away by the simplicity of the cutting templates concept in the first place. I've been cutting foam for a long time and something so simple had never occurred to me. I always use templates for extrados and intrados, but your system is a thousand times better! I sense that you do not use mylar between the core and the beds but rather a soft nylon, one of those used for tablecloths, is that correct? I have been told that with this accessory you do not need mold release or waxes, as I see in your video. Your work is excellent. Thank you for the ideas and solutions you provide.
Yg bikin betah tamu itu deskripsi bang: BAHAN dan Link pembelian (/kata kunci produk). Misal; BAHAN LAMINASI KARBON : - Serat karbon (kata kunci produk: ...). Rp.+- - Resin (.....) Rp.+- - Anu (...) Rp.+- - Anu (...) Rp.+- - Anu (...) Rp.+- Karena sering kita nonton tutorial lalu terjebak/mandek di alat/bahan praktek. Terbebani PR "Sy beli bahannya di mana dengan kata kunci apa?" Maturnuwun Mg sukses barokah Alloohumma Aaminn... :) #kangmalik
Why the joint at the Leading Edge...?...Why not wrap it around using one peice of cloth...?.....The wire temperature is too low as well, this is why the foam cores weren't smooth....😳🇬🇧
Moldless composite construction. Full-Size experimental homebuilt aircraft used this method. See Rutan Aircrafts VariEZ, LongEZ, Solitaire. Edit* Not quite. It's a similar method, but not the same, Rutan designs didn't use the outside of foam to mold it.
@@PILOTGABUS pada-pada Mas Bro lah aku agi blajar iki karo chanel panjenengan ,pokoke chanel panjenengan tak suport Mas Bro,..pokoke tetep semangat jos jos jos...
om beli serat carbon dimana? utk aplikasinya ke bodi stirofoam harus ditekan ya? kalo misalnya saya bikin bodi kapal RC lekukan bodinya beda dgn air foil sayap, cara tekannya lbh sulit
Kalo pake system layer mungkin bisa di coba begini om,body di olesin resin dulu sampai rata dan biarkan sampai setengah kering agak agak kental giti baru di layer karbon dan di tekan tekan dikit setelah itu baru di kasih resin lagi bagian paling luarnya🙏
at 6:00 would you be able to just use the negative of the wing (the one you are supporting the fiber on ) to build the wing cover and just use the spars and ditch the core? is the foam negative rigid enough for a reasonable wing shape or the surface is either too rough or too flexible ?
You have done a good job, have you tried to use a vac. pump? How do you gauge the amount of epoxy going on the surface? Do you just put it on and squeeze it out? Never the less keep out the good work.
I have often used a vacum pump. not everyone has a vacum pump, this video is just a little trick for those who don't have a vacum pump. Thank you friend🙏🙏
Mantap tutorialnya om! Saya ada beberapa pertanyaan. Di video kan om pakai kain karbon nya 2 lembar atas bawah terpisah. Kalau saya pakainya 1 lembar aja memanjang jadi di bagian leading edge sayap ngga kepotong bisa ga yah? Lalu kalau mau pakai kain fiberglass dibanding karbon bisa? Trus untuk lubang spar, bolongin foam nya gimana yah? Terimakasih!
saya gagal fokus terus nih melihat lippo bateraynya,coba pakai pasir yg dibungkus plastik saja ditakar sesuai berat yang dibutuhkan,saya khawatir bateray bisa jatuh atau rusak,..hehehe,...
@@PILOTGABUS dalam proses pemotongan gabus pakai cutting foam pemberat jangan pakai lippo baterai, mending pakai pasir yang dimasukan dalam plastik, sesuai berat yang diinginkan ,lalu diletakan diatas foam ,yang akan dipotong ,bukan dengan meletakan lippo baterai,eman-eman lippo bateraine mas bro,.. mbok kenapa napa bro,..mending lippo baterai dihibahna aring aku baen nek kaya kuwe carane,..hehehehe,...
@@alifuddindae5909 beli online aja banyak om. Kalo mau lokal coba ke tukang dinamo biasanya mereka pake mylar itu bisa di gunakan. Cari yang agak tebal, untuk ngurangin kerutan. 🙏
To press the whole , don't use batterys, easyer is a freezer vacuum pump, put the wing in a plastic bag and make vacuum , you press the whole sureface with 700 or 800 gr /cm²
You can use hotwire if you have one. Make a template on both ends of the wing, where you have a hole for your spar/rod. The just cut a straight line in the templates either from underside of the wing or top, so you can get the wire through that line and also get it out. Then just fill up the straight line on the wing itself and you're done.
s.shopee.co.id/5VDxYLrQ82
s.shopee.co.id/5VDxYLrQ82
For those who make comment about Language, first your brain is multifunctioning and can not think out of the box. Although, I do not understand his language, but instructions and how to make it is very clear.. So, if you have a little knowledge or can functionilise your vision then easy to understand. So, be smart before make any negative comment / So, Thank you my friend for an easy and simple Video to explain it. Great work keep up and I subscribe your channel. ( I am engineer but explanation visually very simple great work )
🙏
Yeah you tell em boy ! Every one fuck off ! Lol
So.. use Li-poly batteries as a weight for cutting with a hot piece of wire. Got it!
@@TheGeorgee lol exactly. Some stupidity is just universal and transcends language
@TheGeorgee There are bigger problems in life. If this is your fear, you will have a lot of issues in RC.
The whole point is how to get vacuum bag results without actually vacuum bagging. Good job.
Mantab Mas Broo.
Selalu sehat dengan daqwah ilmunya buat yg membutuhkan.
I'm satisfied after watching this video and learn alot many thing from your way
thank you very much bro
This is brilliant! What is the clear plastic you use that the resin does not stick to?
Also - curious - what language is the narration in ?
oke pokoke jos chanel ini bro,..tetap semangat dan semoga maju serta sukses selalu pokoke lah
🙏
No mask and no gloves? You should consider using gloves as uncured epoxy has been linked to fertility problems. You also need a barrier mask or respirator as the epoxy dust and especially the inhaled airborne carbon fibers from sanding are damaging to your lungs. Carbon fiber dust is nearly impossible to exhale or cough out of your lungs. If inhaled it will become imbedded and form scar tissue causing reduced lung function over time. A thicker Mylar sheet of plastic will help to smooth out the wrinkles in the finished surface of the wing. The simple use of the PVC pipe as a roller is very clever, I learned something new and I’ve been doing this for 35 years. Nice clear video showing the basics of the process. Thank You
thanks friends, really very useful advice Once again, thank you. 🙏🙏
Mantap om lanjutkan berkariya , semoga nanti bisa bikin heli
Great work. Here's a tip to improve the process; Once you have applied the cloth and resin, wrap in peel ply and then insert it in a storage vacuum bag and pull the vacuum. This will apply maximum pressure and also draw out excess resin into the peel ply. Leave until resin has set.
thanks friends. who want to get a smooth surface. peel ply will not get that. vacum is interesting idea.🙏
@@PILOTGABUS you wrap the peel ply along the edge where the plastic wrapping meets. This absorbs the resin pulled from the cloth.
Thanks friend🙏👍👍
Ternyata ini jago nya carbon...sukses selalu Om...
Alah mak.....saya ni apa lah......prof.cuma anak kemaren sore.mohon bimbingan nya prof🙏🙏🙏🙏
@@PILOTGABUS japri kita ya
Hello
I was blown away by the simplicity of the cutting templates concept in the first place. I've been cutting foam for a long time and something so simple had never occurred to me. I always use templates for extrados and intrados, but your system is a thousand times better!
I sense that you do not use mylar between the core and the beds but rather a soft nylon, one of those used for tablecloths, is that correct? I have been told that with this accessory you do not need mold release or waxes, as I see in your video. Your work is excellent. Thank you for the ideas and solutions you provide.
Good work! Greetings from Germany!!!
🙏
Nice job looks great
akhirnya menemukan video ini, terima kasih banyak om atas berbagi ilmunya.. mau saya coba untuk aplikasi ke wing DLG.
Siap om,terimakasih🙏 wah DLG ya?mantap itu om👍
@@PILOTGABUS om saya email ya. saya mau tanya beberapa hal. terima kasih
WA 085252725429 saya saja pak🙏
Yg bikin betah tamu itu deskripsi bang:
BAHAN dan Link pembelian (/kata kunci produk).
Misal;
BAHAN LAMINASI KARBON :
- Serat karbon (kata kunci produk: ...). Rp.+-
- Resin (.....) Rp.+-
- Anu (...) Rp.+-
- Anu (...) Rp.+-
- Anu (...) Rp.+-
Karena sering kita nonton tutorial lalu terjebak/mandek di alat/bahan praktek.
Terbebani PR "Sy beli bahannya di mana dengan kata kunci apa?"
Maturnuwun
Mg sukses barokah Alloohumma Aaminn... :)
#kangmalik
Trimakasih banyak om ilmunya 😍sangat bermanfaat
Done simply and beautifully. Just amazing.
Video yg sangat menginspirasi, good job!
Mas kalo boleh tau merk resinnya apa? Terima kasih🙏
Eposhcon dari justus om🙏
Tips aja, dari pada pake plastik tebal coba pake plastik belanja, atau beli vacuum pump + bag nya. Yg manual murah kok ga sampe 50rb
Nice work! Looks amazing!
waduh pantesan saya pakai resin biasa gabusnya rontok bro,..makasih infonya tak tahunya pakai resin epoxy
Great work!!!! Congrats ...!!!
🙏
Mantap mas.....aku mau kopi paste mas.....👍
Good work
🙏
Aseeek mantaaaap 😁
Great video
Can you tell me what the plastic end you use on top of the carbon?
Nice! What airfoil is that?
what is the name of the separator you put around the carbon fiber
Terimah kasih! Bagus!!
Very helpful tutorial 👍
Ви найцікавіший історично документальний канал.
Навіть мій аполітичний друг, вас дивиться😌👍
Mantap suhu
Tks om🙏
Gokil update terus
Efek ra ana kerjaan😁
@@PILOTGABUS hehe iso iso setara karo nusantara hobby iki channel le
Adoh om....😁😁😁 ra bisa update tiap minggu aku.nek mas yusuf rutin😁
One other question about building composite wings this way --- How do you get the wing spar through the foam?
Yep great work.
🙏
Keren sekali ✈🛩🛫🛬
Mantab & support .... dimana utk mendapatkan serat karbon nya bang.... ?
Online banyak om🙏
Why the joint at the Leading Edge...?...Why not wrap it around using one peice of cloth...?.....The wire temperature is too low as well, this is why the foam cores weren't smooth....😳🇬🇧
Moldless composite construction. Full-Size experimental homebuilt aircraft used this method. See Rutan Aircrafts VariEZ, LongEZ, Solitaire.
Edit* Not quite. It's a similar method, but not the same, Rutan designs didn't use the outside of foam to mold it.
looks amazing
mantap ,sayang saya gagal fokus terus ama lippo bateraynya,,Mas Bro,..
Suwun pak😊
@@PILOTGABUS sama-sama ,tetep semangat dan ini chanel top markotop pokoke
Chanele rika sing jos..... 😍😍😍pembahasane detail banget👍
@@PILOTGABUS pada-pada Mas Bro lah aku agi blajar iki karo chanel panjenengan ,pokoke chanel panjenengan tak suport Mas Bro,..pokoke tetep semangat jos jos jos...
nunut sinau kang
Mantap ini om, trims ilmunya,kalau boleh tau recomended pembelian bahan karbonya dimana ya om,
🙏 di justus atau mitra komposite om.
@@PILOTGABUS trims om
🙏
Cool. Very nice thanks for the video
Thank you very much for this video,
LOVE FROM I N D I A 🧡🧡🧡🧡🧡🧡🧡🧡🧡🧡
what is the dimension between the leading edge and the carbon fiber hole, or what is the ratio of the tip chord to locate carbon fiber stick
Work shop dimana yaa Mas Broo..
Kalteng om🙏
om beli serat carbon dimana? utk aplikasinya ke bodi stirofoam harus ditekan ya? kalo misalnya saya bikin bodi kapal RC lekukan bodinya beda dgn air foil sayap, cara tekannya lbh sulit
Kalo pake system layer mungkin bisa di coba begini om,body di olesin resin dulu sampai rata dan biarkan sampai setengah kering agak agak kental giti baru di layer karbon dan di tekan tekan dikit setelah itu baru di kasih resin lagi bagian paling luarnya🙏
Serat karbon banyak om di toped
@@PILOTGABUS resinnya pake jenis apa gan
@@tomaskmla7282 resin epoxy om🙏
Beli karbon sheetnya dimana om, pakai yg ukuran berapa? Lanjut terus kreasinya
Banyak om,di toped🙏🙏
@@PILOTGABUS karbonnya yg 200gr/m² atw 240gr
Saya pake yang 200 om.udah lumayan ringan di banding fiber.
thank you
at 6:00 would you be able to just use the negative of the wing (the one you are supporting the fiber on ) to build the wing cover and just use the spars and ditch the core? is the foam negative rigid enough for a reasonable wing shape or the surface is either too rough or too flexible ?
I believe you can but you won't get a perfect leading edge
leading edge will be finishing again
great video. can u say what was the 3rd liquid u added to epoxy. because foam burns when its coated with epoxy. please do help
epoxy resin and hardener, it won't burn foam. I only use 2 components, epoxy resin and hardener.🙏
Depends on the type of foam AND it also depends if it's epoxy or polyester resin
👏
You have done a good job, have you tried to use a vac. pump? How do you gauge the amount of epoxy going on the surface? Do you just put it on and squeeze it out? Never the less keep out the good work.
I have often used a vacum pump. not everyone has a vacum pump, this video is just a little trick for those who don't have a vacum pump. Thank you friend🙏🙏
Mantap tutorialnya om! Saya ada beberapa pertanyaan. Di video kan om pakai kain karbon nya 2 lembar atas bawah terpisah. Kalau saya pakainya 1 lembar aja memanjang jadi di bagian leading edge sayap ngga kepotong bisa ga yah? Lalu kalau mau pakai kain fiberglass dibanding karbon bisa? Trus untuk lubang spar, bolongin foam nya gimana yah? Terimakasih!
Bisa saja om,tapi takut kurang tekanan di LE nya ntar jadi kopong kalo bisa lebih hati hati di bagian ini.fiber bisa aja mas.
Melubangi spar di sini th-cam.com/video/SFPbkV-84uc/w-d-xo.html
Hey bro! Love the video. What plastic did you use? Hai kawan! Suka videonya. Plastik apa yang Anda gunakan?
I call it astralone plastic. using 0.20mm mylar is the right choice.🙏
@@PILOTGABUS Awesome man thanks heaps! Keep up the great videos! Really amazing what you can do when you put your mind to it!
Ini lapisannya atas bawah apa atas aja om..? Boleh diberikan gak nama nama bahannya apa aja... Berapa gsm itu serat carbonnya..
Atas aja om,bahan serat karbon 200gsm sama resin epoxy
pakai plastik apa y om?? kok poxy gak nempel di plastiknya ya om???
Mylar om
What weight cloth did you use?
Terima orderan kah om..?
Good Work! What density of carbon fibre cloth did you use?
3k 200gsm🙏
what is the name of that plastic which you have used
Astarlon or mylar can use🙏
Apakah cairan resinya tidak merusak permukaan sterofoam mas?
Kalo resin epoxy aman om.
saya gagal fokus terus nih melihat lippo bateraynya,coba pakai pasir yg dibungkus plastik saja ditakar sesuai berat yang dibutuhkan,saya khawatir bateray bisa jatuh atau rusak,..hehehe,...
Siap pak bro, sebenarnya jos pake vacum.
@@PILOTGABUS hehehe,..iya
😁😁😁tapi itu kan foam yang soft, kalau di vacum langsung gepeng😭😭
@@PILOTGABUS dalam proses pemotongan gabus pakai cutting foam pemberat jangan pakai lippo baterai, mending pakai pasir yang dimasukan dalam plastik, sesuai berat yang diinginkan ,lalu diletakan diatas foam ,yang akan dipotong ,bukan dengan meletakan lippo baterai,eman-eman lippo bateraine mas bro,.. mbok kenapa napa bro,..mending lippo baterai dihibahna aring aku baen nek kaya kuwe carane,..hehehehe,...
@@TegoSuwarto seh.. Malahaku sing gagal vokus 😃😃😃
Om tanya dong itu plastik apa ya kok tebal kayaknya atau khusus
Iya om plastik khusus,belinya di toko Bahn bahan giber gitu om
Tolong donk mas, kok saya pake pake plastik Astralon jadi lengket nempel ya?? Boleh kasih linknya penjual plastiknya? Makasih... 🙏
tokofrp.com/main/subcategory/140-polyester-film
om... mohon infonya.. serat Carbon apa n spesifikasi nya.. 🙏
tokopedia.link/lY7LYyqHYzb ini om🙏🙏🙏
@@PILOTGABUS makasih infonya om...
itu plastik astralon gakperlu dilapisi wax lagi kah om? biar gak lengket
dan biasanya belinya dimana?
@@alifuddindae5909 tidak perlu wax
@@alifuddindae5909 beli online aja banyak om. Kalo mau lokal coba ke tukang dinamo biasanya mereka pake mylar itu bisa di gunakan. Cari yang agak tebal, untuk ngurangin kerutan. 🙏
misalnya media utama wing pakai balsa gimana om? total berat wing span 1.10m 97gram.
Bisa aja om🙏🙏
Those fingernails….
Pesan, beli sayap boleh? mirip beginian boleh yg di vidio ini, saya bikin gk rapih, kalau bisa pesan?
شما از چه نوع فومی استفاده کردید
Apakah Resinnya tidak membuat meleleh terhadap gabus/styrofoam nya kak?
Saya subs dan kasih jempol ke atas atas ilmunya yg bermanfaat🙏🙏
🙏🙏resin epoxy aman om.
Bang mohon info, akamat toko jual serat carbonnya dan ukuran serat carbonnya atau mereknya. Semoga di respon. Terimakasih.
Banyak aja om di toped
tokopedia.link/t6lcBhIxmCb
@@PILOTGABUS terimakasih om responnya
Hello sir, I have a question. Do I need to calcute where I need to do the thickness spot and how thick do I need to do it?
To press the whole , don't use batterys, easyer is a freezer vacuum pump, put the wing in a plastic bag and make vacuum , you press the whole sureface with 700 or 800 gr /cm²
Good advice, especially if the Lippo is hit by a wire or an error occurs that is quite unfortunate.
👍
What are the plans and measures of this man? maybe i will do it too
This is the plan for the Skywalker Wing. there is length of about 2000mm.
Mau tanya, sterofoam nya jenis apa ya?
Sterofoam biasa om.
@@PILOTGABUS sterofoam jenis yang biasa djual di toko alat tulis atau yang kya gmna mas? Untuk pembeliaannya dmna?
Betul om tinggal sesuaikan ketebalanaya.resin nya pake yang epoxy resin ya,jangan resin yang di pake buat kapal.
@@PILOTGABUS oke siap 👍🏼 terimakasih informasinya, semangat terus mas untuk channel nya,
👍🏿
itu plastik di kasih lapisan g om biar g len yg ket ke resin
Gak ada lapisan om.kalodah kering sempurna resin nya gak lengket🙏
campuran resin dan hardenernya 1 banding berapa om?
2:1 tergantung merk om
Pakai resin apa bang
Epoxy
@@PILOTGABUS merek apa bang yg bagus
lycal bagus justus juga bagus yang epocshon
@@akiudjiu7157
Which is the epoxy that u have used
i use justus.
izin bertanya min, untuk pemilihan resin itu gimana ya min ?
Cari resin epoxy om🙏
pake foam jenis apa, styrofoam kah?
betul
What kind of film on fiber ?What is the name of the film?
Astralon plastic or mylar can use. 🙏
pak music nya tolong di matikan .. bikin mumet
What resin is used?
Epoxy resin🙏
@@PILOTGABUS of course is epoxy, what brand is it
@@scottdunlap4109 I use the brand "justus"
Nice hot wire bow. Any way I could get the "how to build it" instructions somewhere? Thanks
untuk beli karbon dan resin d mna yah mas
Di toped banyak aja om🙏
how did you drill through the styrofoam to put a rod in it? My advisors have been telling me it will be difficult to make a hole through styrofoam
You can use hotwire if you have one. Make a template on both ends of the wing, where you have a hole for your spar/rod. The just cut a straight line in the templates either from underside of the wing or top, so you can get the wire through that line and also get it out. Then just fill up the straight line on the wing itself and you're done.
I'm bad at explaining so found a video of what I meant. Shows it at 4mins mark.
th-cam.com/video/SFPbkV-84uc/w-d-xo.html
Apakah ada kontak yg bisa dihubungi, mau nanya nanya terkait serat karbon komposit.
tovikg@gmail.com
Plastik nya ada dilapisin wax om?
Tidak perlu om🙏
@@PILOTGABUS Ok om makasih info nya...salam dari Aeromodelling Aceh.
🙏
What did he use to cut the foam so perfectly?
Hot wire
Que cola e essa amigo
Mas.. kalo buat carbon seperti ini untuk sayap ukuran panjang 3.5m dibagi 3 bagian kuat gak ya?
Bisa aja mas, ditambahin spar lagi. Dan joiner nya di buat sedemikan rupa supaya presisi dan kuat🙏
@@PILOTGABUS ada wa mas? Mau konsultasi tanya kl gak merepotkan 🙏🙏
085252725429
wing bleber
Mbrebet man
Ou avez vous trouvé le gabarit ? Merci