Morris Minor, Removing Body Panels & rear bumper, Project Mildred EP 03
ฝัง
- เผยแพร่เมื่อ 5 ต.ค. 2024
- In the third episode of Project Mildred, we show you how we Remove the Body Panels & rear bumper.
During the Covid lockdown of 2020 Lou & Pete decided to purchase a Morris Minor 1000 1961 1100cc. With no prior experience in vehicle restoration they decided to undertake a challenge unlike any other they had undertaken before. This is their journey.
Help Support the Chanel : / projectmildred
contact us:
Facebook: @ProjectMildred
email: axbyandhirst@hotmail.com
Check out our other youtube Chanel:
The Island Workshop: / @theislandworkshop8453
The gear we use :
Wurth Pump bottle & brake fluid : amzn.to/2MNxIYf
Amtech wire brush set : amzn.to/37qgeei
3 in 1 oil : amzn.to/2UCsV06
Amtech panel body hammer kit : amzn.to/2B2RXyt
Parweld 115mm 100pk cut off discs : amzn.to/3dVMurQ
6 Rolls masking tape : amzn.to/3ffjDPx
Steel Straight edge : amzn.to/2AqM7qV
Flux core welding wire 3pk : amzn.to/30zAcSs
Hilda parts washer : amzn.to/2UxEZA0
Air Punch / flange punch : amzn.to/3fjobEP
Air Die grinder : amzn.to/2AZVMEK
Tungsten cutters : amzn.to/2UzYl7j
Wire wheel 6 inch : amzn.to/30KyoWT
Skin pin pliers : amzn.to/3fe0c9L
Skin Pins : amzn.to/37oDzg5
Spot weld cutters : amzn.to/2MMcV7w
Flap discs 115mm 10 pk : amzn.to/3hlk3G8
Parts washer / degreaser : amzn.to/3fgitTW
Air pistol/ smaller : amzn.to/30A1VCy
Valve spring compressor : amzn.to/30y3rF5
Autotek etch primer grey : amzn.to/30wRWO3
Sealed breaker bar : amzn.to/2Uy3uNa
Impact sockets 5pk : amzn.to/2MS6G1Y
Sanding discs sorted : amzn.to/3hhimtb
Engine paint enamel : amzn.to/2Uyt30G
Valve lapping kit : amzn.to/2YtMl8u
Feeler gauges : amzn.to/3dVPwMK
Torque wrench : amzn.to/30wSJP1
Stud remover : amzn.to/3hmlAeO
Haynes manual : amzn.to/3fgjYBy
Gazebo : amzn.to/3hlrRre
Peggs : amzn.to/30Cnr9x
wire wheels : amzn.to/2Ys0CCF
Welding jacket : amzn.to/30uWLHT
welding pliers : amzn.to/30xpv2x
welding tips : amzn.to/3hlmGI0
Gt85 : amzn.to/2Yp6htf
If you guys would like to help support there channel, please take a look at our new Patreon page: www.patreon.com/projectmildred
The more you take off, the more we can see just how much work you have to do! Good luck!
oh yer your telling me
Project Mildred It’ll be worth the hard work in the end though.
Great videos, I am happy they came up as recommended. Keep up the good work. The car isn't as bad as I first thought. Can't wait to hear you swear at those brass screws, from the gearbox cover. 🤣🤣🤣🤣
haha thanks for watching
your doing a great Job
thanks for watching
Great work. Certainly rapid progress. It would be nice *for me!* to see a little more close up detail on locations of fixings. I appreciate you're on a job though and trying to crack on!
Look forward to seeing more 👍
ok yer i get you, a bit more detail /step by step. i will take that on board mate, we did the initial strip down in 6 consecutive days. so up to episode 6/7 i think, so we were going at quite a rate. things have obviously slowed down quite a bit and the process of putting her back together will be a more calculated step by step. I'm learning as i go along. thanks for watching
Loving these videos, keep them coming
thanks man, really enjoying making them, can't wait to get cracking of putting her back together
Another good episode, looking forward to next week👍
Doing a grand job sir 😎
thanks mate, we recently received a load of new panels from ESM so can't wait to get cracking on the rebuild
What's that Ryobi wrench worth? Looks like really doing the job, would love to get one for my Maurice.
yer its bloody good for the money, ive had it for about 5 years now doesn't skip a beat
do get some axle stands-much safer.
yer we now have a rollover jig so not needed at the moment