Thank You very much for the clear, informative tutorial! I'm doing apartment maintenance in Norman, Oklahoma. We have compact GE washers that look very similar to your LG. I was called to check out a tenants washer that would cycle just fine until it came to spin. Would never have considered that the fault may be with a short in the water intake solenoid. Now I have a fix to try.
I don't have a multimeter at the moment and I wanted to test my solenoid. You gave such a good advice is to bypass the solenoid and start spinning mode. If the drum start turning it means defective solenoid. Thank you so much.
been searching youtube a while as i have the same problem with my washer after it was exposed to the rain water... will try this tomorrow.... many thanks.
What if my washing machine water does not stop filling the drum when it reaches the desired amount and now spin does not work too. Is the solenoid valve the problem?
Hi Ravi! when the machine is in wash, the bottom makes a lot of noise like bearing sounds and the wash sometimes doesnt move. But during spinning it spins ok. Any idea why? thanks
First check the belt tention which spin the drum by a motor. And check washing parts inside the drum which is use for wash cloths by rotating. Sometimes they might be loos.
I had did the same almost but the only thing was the part which I couldn’t find exact one but thanks for sharing so now I can but different solenoid and replace the now water inlet valve thanks a lot
I have the 8.2Kg machine which is almost identical and does not spin, when carrying out the the same test at 3 the drum does not spin but I get a DE flashing on the display - is this the same problem with the water level switch?
Hi Brian mine is doing just that. Flashing DE which means distribute evenly. Did this with no success even when machine is empty. Did you end up fixing the issue. Thank you in advance
Hi Ravi,my LG top load does not take in water during rinse cycle and there isvoice coming,spin cycle works fine,.water intake is fine during soak or wash.what could be issue.
Check the piece of magnet fix on the lid wich use to send the door closed signal. When it loos this error could occur. It is a common problem for this machine.
Hello I have I problem with my LG FUZZY LOGIC. THE PROBLEM OF MY WASHING MACHINE IS THAT WHEN EVERY TIME I WASH THE DRAIN MOTOR IS PULLING THE DRAIN PLUG AND IT WILL NOT MAINTAIN THE WATER REQUIRED to wash spin.. but when I disconnect the hook on the drain plug. It will wash and I put i back again so that it pulls the drain motor to drain so it will continue to spin.... What is the required step to fix this Or should I replace the mother board of the lg fuzzy logic.?. Can you help me to decide what to do.
Mainly this error could occur due to Bad water level sensor. Better you replace it first as it is not so expensive. But this error could occur due to bad drain valve motor or bad mother board too. But mostly my experience with this machine with the bad water level sensor.
Sir I hv samsung wooble automatic washing machine, somtime when machine is in spin mode only pulslator is working but drum is not working and some time dhrum is also working but it's work slow ,so I hv change capacitor also and I hv check the belt also ,then also drum work slow ,son please let me know what to do which part is not working thanks
If other functions work properly, problem might be in water level indicater switch. Just reset it by removing it's small hose from the tub end and blow it by mouth, if you hear clicking sound that mean switch is ok and reconnect it to the tub. Next look for the drain hose and the filter is it blocked, if so clean it, these two options also can cause to stop some option in a properly working washing machine.
videocon digi gracia 5.5 kg rinse & spin problem how rectify the issue washing is normally running, but after washing water Rejetecion not working, just blinging rinse led light
Check both water intake valve and water level sensor, they could make this kind of faults. Also drain valve or pcb, stuck drain hose could be. Check one by one.
all the modern washing machines are good with modern technology. personally I love LG brand with Korean Technology. however I can't condemn other brands also as they are good too. I would like to mention here as we are Asians, Korean brands are good and durable for our budget
Ravi ji, heavy smell like something burned. After when tried to switch on, all button lights on. But drum spin very slow & stops & little burn smell again there. Any idea how to sort this out?
Hi Ravi, tried again, put some water, machine drained water. Then I tried to spin, it started little 2 seconds spin, not even 1 half circle, it looks like any belt problem you recon ? Plz advise
I have LG Fuzzy Logic 6.0kg machine. I got the problem that shan i start the machine the 2 indicators beeps after a minute full loading of water and starts washing. The indicators are wash & spin. What to do?
if you try already this video and not respons Try this video with below link which is diagnose the water level sensor. th-cam.com/video/R__VMKuJg00/w-d-xo.html
Help me sir im not getting water for rinse cycle... Wash cycle is ok. It takes water and starts to wash but when it goes to rinse mode water does not fill and stops function
If it is the problem with water intake valve motor, it will cost 4$ ABOUT, if the problem with water level sensor, it will cost 6$ about. but it depend on the which part is malfunctioning.
I was happy about your video because I have the same problem with my lg I did everything like you but the SPIN still doesn't work What else can it be please urgently for your help dear greetings ewald
Ravi Fix may be I just opened n saw the clutch which unclocks the gears of bucket is not unlocking, so what u think it’s still gear box or drain motor issue
Bro excellent job N nice language and presentation i am going to subscribe you. U deserve it. I am also doing some maintenance of equipments. Same LG unit almost same fault am facing now. When i was not in my house, someone attended the issue 2 time and bribed 2000 twice still there is same issue. While washing several times its stopping. When i refresh the connection or reset the wiring again its running. Could you tell me what will be the issue.
I also have same problem,but I am not using water input through solanide valve.i am taking water manually.what to do.my spinner not working.pls reply.many thanks
Watch this video, th-cam.com/video/R__VMKuJg00/w-d-xo.html it might help you. I cant't say exact what it is, as it is a manual or semi automatic machine without inspection or more details.
Bro, i have same washing machine, the problem is the drum is rotating once or twice and then then buzzer sounds and the operation stops. During spin , the water moves out of machine but the dr do not rotate. Please tell me the solution for it.
Yes, but sensor might be faulty with short circuit, then it affect for the other functions like wash and rinse. But it fill right water level eventhough . If you have a multimeter you can check it.
I have a problem where the P E is flashing on the front panel and the machine is beeping when P E notice comes on. It's not spinning. It's a 13.5 kg LG toploader turbo. Pls assist me as I'm a disabled pensioner, need urgent assistance. Thank you.
PE error comes for the water level sensor, first thing you can do is, unplug the machine and leave it several minutes and then try again. If not response for this reset method, have to replace water level sensor, you might need professional mechanic.
Could you please help, My LG top load automatic washing machine in the spin mode it is taking water (it should not take water for spin function right?) and draining continuously, so spinning not happening. And when power button is switched off and mains is on main motor is running slowly. what could be the problem?
Problem might be with the water level indicater switch. Please Watch this vedio to get an idea about water level indicater switch th-cam.com/video/lwHrJvJ8KTI/w-d-xo.html However need more details to guess and diagnose.
I have same problem but I try your advice but not solving when I remove the connection that time also not work but i keep empty and pipe state then that is working. I am not understanding 🤔
Just try with water level indicate switch, First remove the small hose wich connect to the tub from water level indicate switch. Next blow it up by mouth and reconnect it. Then look for the spin function does it works.
Machine is stoping after wash in Rinse and blinking but when i do state the drain pipe and water come out then that machine are working what i shoud do pls help
Hey bro I got the same type of washing machine,,my spinner is not washing the clothes nicely and clothes are still wet after the cycle,,what do u think the problem is?any solutions??
Make sure that Wash, Rinse and spin function are activated with your washing cycle. If all are activated must be a problem. Otherwise end of the cycle cloths shoud be air dried. Try just activating only the spin option and get it dry. Then you could understand spin option is working properly or not
Ravi Fix all functions are activated during cycle. Tried just the spin cycle as well and still clothes are too wet. Not spin dried enough. Could it be motor problem? What would you recommend?
Can you understand that it has too slow spinning than it was before., might be a problem in the motor. However check the motor belt tention also by removing the back cover and squish the belt together
Ravi Fix hi Ravi have just been watching you fixing another washing machine you probably be able to help us with hours which is a different MKe, ours. Is a LG T. 655a top loader.the problem appears to be a buildup of rubbish in the three vertical plastic channels leading to the removable filth filters. Problem starts with how to remove all of the plastic covers over the drum to access the three vertical channels. Thanks Bob and Marina.
Rotation speed depend on the washing option you select. Fuzzy mode or gentle mode like that. Check it with different washing mode and different watter level without clothe to get an idea. If it is too slow just check the motor belt tention underneath.
hi sir im from malaysian, how to reset model LG WF-HD100FS error code AE. I change new drain motor but cannot functional well. How can i reset sir. Can you help me... Thanks.
This might have a PCB error, disconnect power from main and leave it 15 20 minutes, and try it. Otherwise look for any small water leak somewhere in the system toward draining system after you re installed wich can make water level sensor confused.If not any issue, check the PCB by a professional person.
Without more information hard to diagnose. However if it is a top loaded machine, please check the door is it available the peace of magnate which is provide a signal that door is closed. This problem can occur due to loos that peac of magnate on the door.
Thank You very much for the clear, informative tutorial! I'm doing apartment maintenance in Norman, Oklahoma. We have compact GE washers that look very similar to your LG. I was called to check out a tenants washer that would cycle just fine until it came to spin. Would never have considered that the fault may be with a short in the water intake solenoid. Now I have a fix to try.
Very helpfull presentation.
Best I get 2 benefits from this video 1 solution of fault & to learned english
Thanking you
Thanks a l appreciated your efforts to help
I have been struggling it did not spin to wash it is my pleasure to open my eyes God bless the TEAM
I don't have a multimeter at the moment and I wanted to test my solenoid. You gave such a good advice is to bypass the solenoid and start spinning mode. If the drum start turning it means defective solenoid. Thank you so much.
been searching youtube a while as i have the same problem with my washer after it was exposed to the rain water... will try this tomorrow.... many thanks.
Washing wash
Thank you very much for the information of technical defect in
Washing machine.
Many thanks for using English. I like your videos. Kenya East Africa
thanks for your help..i fixed my wife's washing machine ( lg inverter direct drive)
Good nice presentation please do more videos we are expecting from you many ideas
Thank u thank u so much bcs I have same problem and for this I have searching many videos
Thankyou brother I have searched for the same problem . Thankyou .
Tnx for sharing master..bagong kaibigan..sending my full support
Very good always mind is set for pressure sensor defects but it's clear today thanks🌹
Thanks for this tutorial. I have spinner problem.
Your explanation is worth tnan a world thank you very mouch sir 🙏
God bless you, sir 🙏 🙌 ❤️ ♥️
Nice to see your video. It helps me a lot thanks
Good job bro...I need this in the future
Nice super sir well explained
I have a newer model 13kg with 2 solinoids. 1 for cold and one for hot. Should i diconect both solenoids when doing the test?
Try both
What if my washing machine water does not stop filling the drum when it reaches the desired amount and now spin does not work too. Is the solenoid valve the problem?
Does it indicate any error code?
@@ravifixall No error code it just doesn't spin
Thanks mechan! It helped me!! 👍👍
Good job bro...I need this in the future... thanks.
Hi Ravi! when the machine is in wash, the bottom makes a lot of noise like bearing sounds and the wash sometimes doesnt move. But during spinning it spins ok. Any idea why? thanks
First check the belt tention which spin the drum by a motor. And check washing parts inside the drum which is use for wash cloths by rotating. Sometimes they might be loos.
@@ravifixall thanks bro. will check it out 😃
@@ravifixall yh
Thank you soo much 🙏 it was very informative 👍👍
Hi
Very well explained thank you
I had did the same almost but the only thing was the part which I couldn’t find exact one but thanks for sharing so now I can but different solenoid and replace the now water inlet valve thanks a lot
I have the 8.2Kg machine which is almost identical and does not spin, when carrying out the the same test at 3 the drum does not spin but I get a DE flashing on the display - is this the same problem with the water level switch?
Hi Brian mine is doing just that. Flashing DE which means distribute evenly. Did this with no success even when machine is empty. Did you end up fixing the issue. Thank you in advance
Where we get solonoid valve in washing machine? Outgoing water is not going during Spin function?
I have the doubt water intake function is ok then washing and dryining ok but ispin only not waking problem is solonite vall ?
Hello ,my LG top loader serial no 204Kw00654 doesn't want to switch on ,what do you think the problem is?
Make sure you have powe from wall to the machine, next check main fuse in the washing machine.
Hi Ravi,my LG top load does not take in water during rinse cycle and there isvoice coming,spin cycle works fine,.water intake is fine during soak or wash.what could be issue.
Where can I get LG wf-701 suspension rod....Abans hv no stock
Sorry. No idea
Nice work truly nice work
can you make more video on washing mashchin your video is very imforetive...thnx
I was told LG is Flawless and it would be a rare event if it stopped performing
Do you have a work shop in galle?
I have LG top load fuzzy logic washing machine timer stcuk .wshing time take too long how to fix it
Bro did u find the solution for ur problem shre me that video
Bro did u find the solution for ur problem plz shre me thar video
Thanks for sharing this video master.
Your Video is nice & very clear instructions. I have same machine & it's giving error code de . Pls help me showing a video fitting that. 🙏
Check the piece of magnet fix on the lid wich use to send the door closed signal. When it loos this error could occur. It is a common problem for this machine.
What is the any other problems are coming to not working only spin
Hello I have I problem with my LG FUZZY LOGIC. THE PROBLEM OF MY WASHING MACHINE IS THAT WHEN EVERY TIME I WASH THE DRAIN MOTOR IS PULLING THE DRAIN PLUG AND IT WILL NOT MAINTAIN THE WATER REQUIRED to wash spin.. but when I disconnect the hook on the drain plug. It will wash and I put i back again so that it pulls the drain motor to drain so it will continue to spin....
What is the required step to fix this
Or should I replace the mother board of the lg fuzzy logic.?. Can you help me to decide what to do.
Mainly this error could occur due to Bad water level sensor. Better you replace it first as it is not so expensive. But this error could occur due to bad drain valve motor or bad mother board too. But mostly my experience with this machine with the bad water level sensor.
@@ravifixall where can I locate that hope you cud have step by step tutorial in this problem
th-cam.com/video/R__VMKuJg00/w-d-xo.html
where can i get this volve?
Try in a local partstore.
My area water TDS is about 800 , will high TDS damage the top load washing machine
What is the rate of.the.belt. the belt of my lg 6.2 ia.broken
what if doesn't run when you disconnect the solenoid valve. i have the same problem in LG smart inverter 10kg top door. please can you guide
Sir I hv samsung wooble automatic washing machine, somtime when machine is in spin mode only pulslator is working but drum is not working and some time dhrum is also working but it's work slow ,so I hv change capacitor also and I hv check the belt also ,then also drum work slow ,son please let me know what to do which part is not working thanks
Check the drain motor which release the brake to let the spin drum faster.
Look at that... It works
Hello. I have Samsung top loader 7,5kg has the same problem. If the water in take valve is not the problem what else could be the problem. Thanks.
If other functions work properly, problem might be in water level indicater switch. Just reset it by removing it's small hose from the tub end and blow it by mouth, if you hear clicking sound that mean switch is ok and reconnect it to the tub. Next look for the drain hose and the filter is it blocked, if so clean it, these two options also can cause to stop some option in a properly working washing machine.
Thankyou, Very useful.
i have110v inlate valve .but if i replace to 220v is it work?
Hey even I’m a service tech here . Don’t give wrong info to public please if there is spin issue uh have to check with outlet Drane motor boss
Can you tell water is draining properly but not spinning. And giving OE error
what to do ?
pls reply
Wrong
@@rangabilla9942 bro same issue I'm having , can u tell me pls how u fix it
Well can you help me lol 😂
Where i can get spin motor of fuzzy logic 7.5 kg. Because my washing machine there is spinning problem.
After removing the wire from the Water intake valve solenoid, the spin still does not work. Does that means the Water intake valve solenoid is OK ?
Water level sensor may cause this issue.
@@ravifixall can we repair water level sensor?
videocon digi gracia 5.5 kg rinse & spin problem how rectify the issue washing is normally running, but after washing water Rejetecion not working, just blinging rinse led light
Kindly help me
After washing prosses drain function not working, just blinking led rinse
I Have Lg wm WF T- 7519PV but now speaking funcation ( washing start washing complete) is not working how can repair. Pl. gjve demo repair.
Hi Ravi, my rinse function and spin function is not working. Where is the problem ?
Hi spin issue with same model, spin mode,6 minutes time will move to 3 minutes immediately after selection & later spinner no work ,kindly advise
Check both water intake valve and water level sensor, they could make this kind of faults. Also drain valve or pcb, stuck drain hose could be. Check one by one.
Is the spin problem related to board
Hi bro its nice video i lke it but u have fullyautomatic to sami automatic converting video upload it bro thnx
th-cam.com/video/HrxIlNM67vo/w-d-xo.html
After removing wire, it doesn't start spinning. Facing same issue..What should I do?
Hi Sir lg automatic washing machine model WFS65A01AHT spin washing working only other functions like rinse, Washing not, please guide me about it
hi, how we can fix wire breaking problems because rat making like issues
You get the rat guard for this model.
Install it underneath.
Sir,
Which washing machine is better
IFB vs Lg as per ur experience?
Please suggest good washing machine
all the modern washing machines are good with modern technology. personally I love LG brand with Korean Technology. however I can't condemn other brands also as they are good too. I would like to mention here as we are Asians, Korean brands are good and durable for our budget
Excellent .
Thank you.
Why spin is very slow and clothes not dranin properly how it's will repair
Ravi ji, heavy smell like something burned. After when tried to switch on, all button lights on. But drum spin very slow & stops & little burn smell again there. Any idea how to sort this out?
Seems to be electrical short somewhere else. Better get professional technician's support to avoid hazards.
Hi Ravi, tried again, put some water, machine drained water. Then I tried to spin, it started little 2 seconds spin, not even 1 half circle, it looks like any belt problem you recon ? Plz advise
hi . . i want to ask question . .what is the cause if the drain motor open when i push on the srart button
Check the water level sensor.
I have LG Fuzzy Logic 6.0kg machine. I got the problem that shan i start the machine the 2 indicators beeps after a minute full loading of water and starts washing. The indicators are wash & spin. What to do?
if you try already this video and not respons
Try this video with below link which is diagnose the water level sensor.
th-cam.com/video/R__VMKuJg00/w-d-xo.html
Help me sir im not getting water for rinse cycle...
Wash cycle is ok. It takes water and starts to wash but when it goes to rinse mode water does not fill and stops function
Check the water level sensor, drain hose is not clogged and check drain valve too. Hard to say what it is exact without inspection.
videocon fuuly aitomatic washing machine spinner not working how much money we want to spend for the replacement of parts or to buy the new parts
If it is the problem with water intake valve motor, it will cost 4$ ABOUT, if the problem with water level sensor, it will cost 6$ about. but it depend on the which part is malfunctioning.
Plz tell us, the temperature issues in LG frontload Washing machine
Good advice great
The washer only work in a clockwise directing, why.?
Seems to be transmission problem.
Where to get this spare solenoid valve..?
Have to look in a local part store who sale washing machine parts. Otherwise look in ebay or online.
I was happy about your video because I have the same problem with my lg
I did everything like you but the SPIN still doesn't work
What else can it be
please urgently for your help
dear greetings ewald
Excelent explanation
The pulsator of the machine is not open, how to open it?
Solenoid valve no need rating?
What do you mean with rating?
Voltage , ampere
I have a similar issue like mine bottom plate is spinning but the round bucket is not spinning can u help me out..
This is seems to be gearbox error.
Ravi Fix may be I just opened n saw the clutch which unclocks the gears of bucket is not unlocking, so what u think it’s still gear box or drain motor issue
Hard to say exact, however check the drain motor too. It can affect too.
Bro excellent job N nice language and presentation i am going to subscribe you. U deserve it. I am also doing some maintenance of equipments. Same LG unit almost same fault am facing now. When i was not in my house, someone attended the issue 2 time and bribed 2000 twice still there is same issue. While washing several times its stopping. When i refresh the connection or reset the wiring again its running. Could you tell me what will be the issue.
Thank you. Check bothe water intake valve solenoid and the water level sensor one by one. This knid of errors could occur due to both components.
My home Washing Machin water over flowing ,what problem?
first Check water intake valve motor, sometimes this error could occur due to bad water level sensor.
I also have same problem,but I am not using water input through solanide valve.i am taking water manually.what to do.my spinner not working.pls reply.many thanks
Watch this video,
th-cam.com/video/R__VMKuJg00/w-d-xo.html
it might help you. I cant't say exact what it is, as it is a manual or semi automatic machine without inspection or more details.
Hello bro.
My washing machine is suddenly stop in middle. Suddenly turning off. What is the problem and how can I solve it.
Bro, i have same washing machine, the problem is the drum is rotating once or twice and then then buzzer sounds and the operation stops.
During spin , the water moves out of machine but the dr do not rotate.
Please tell me the solution for it.
Check the water level sensor
th-cam.com/video/R__VMKuJg00/w-d-xo.html
@@ravifixall the water level is working fine, the water gets filled as per the s, m, l volume.
Yes, but sensor might be faulty with short circuit, then it affect for the other functions like wash and rinse. But it fill right water level eventhough . If you have a multimeter you can check it.
Bro water not going out side after wash
So which problem pls reply
I have a problem where the P E is flashing on the front panel and the machine is beeping when P E notice comes on. It's not spinning. It's a 13.5 kg LG toploader turbo. Pls assist me as I'm a disabled pensioner, need urgent assistance. Thank you.
PE error comes for the water level sensor, first thing you can do is, unplug the machine and leave it several minutes and then try again. If not response for this reset method, have to replace water level sensor, you might need professional mechanic.
How about na wash is not working but the spin is working?
Same problem but cant fix this issue, other solutions?
Check the water level sensor.
Could you please help,
My LG top load automatic washing machine in the spin mode it is taking water (it should not take water for spin function right?) and draining continuously, so spinning not happening.
And when power button is switched off and mains is on main motor is running slowly. what could be the problem?
Check the water level sensor as in below video.
th-cam.com/video/R__VMKuJg00/w-d-xo.html
Bro my washing not spinning but after i spin manually it start to spin . Is it capacitor promblem or what ?
Problem might be with the water level indicater switch. Please
Watch this vedio to get an idea about water level indicater switch
th-cam.com/video/lwHrJvJ8KTI/w-d-xo.html
However need more details to guess and diagnose.
I have same problem but I try your advice but not solving when I remove the connection that time also not work but i keep empty and pipe state then that is working. I am not understanding 🤔
Just try with water level indicate switch,
First remove the small hose wich connect to the tub from water level indicate switch. Next blow it up by mouth and reconnect it. Then look for the spin function does it works.
Ravi Fix can you give any video link pls
Machine is stoping after wash in Rinse and blinking but when i do state the drain pipe and water come out then that machine are working what i shoud do pls help
Drain pipe or draining filter might be blocked. Check it and clean it if so.
In my machine spine is working but wash not working sir what to do?
Does it take water in? And any error code appear on the display?
@@ravifixall manual water we filling, no one error appears sir, spinning done properly.
Hey bro I got the same type of washing machine,,my spinner is not washing the clothes nicely and clothes are still wet after the cycle,,what do u think the problem is?any solutions??
Make sure that Wash, Rinse and spin function are activated with your washing cycle. If all are activated must be a problem. Otherwise end of the cycle cloths shoud be air dried. Try just activating only the spin option and get it dry. Then you could understand spin option is working properly or not
Ravi Fix all functions are activated during cycle. Tried just the spin cycle as well and still clothes are too wet. Not spin dried enough. Could it be motor problem? What would you recommend?
Can you understand that it has too slow spinning than it was before., might be a problem in the motor. However check the motor belt tention also by removing the back cover and squish the belt together
Ravi Fix hi Ravi have just been watching you fixing another washing machine you probably be able to help us with hours which is a different MKe, ours. Is a LG T. 655a top loader.the problem appears to be a buildup of rubbish in the three vertical plastic channels leading to the removable filth filters. Problem starts with how to remove all of the plastic covers over the drum to access the three vertical channels. Thanks Bob and Marina.
th-cam.com/video/IHPUauZAftM/w-d-xo.html
Just try this vedio.
I hv fizzy logic top load 7kg w.machine during washing its speed is quite slow .can u guide me?
Rotation speed depend on the washing option you select. Fuzzy mode or gentle mode like that.
Check it with different washing mode and different watter level without clothe to get an idea. If it is too slow just check the motor belt tention underneath.
Ok good what is cost of this lg gear box
m.indiamart.com/impcat/washing-machine-gearbox.html
hi sir
im from malaysian, how to reset model LG WF-HD100FS error code AE. I change new drain motor but cannot functional well. How can i reset sir. Can you help me...
Thanks.
This might have a PCB error, disconnect power from main and leave it 15 20 minutes, and try it. Otherwise look for any small water leak somewhere in the system toward draining system after you re installed wich can make water level sensor confused.If not any issue, check the PCB by a professional person.
Tq for the good info..
Where can i buy m.parts.
Just find in local parts store. Otherwise everything available in ebay.
@@ravifixall
Thank you..
My lg washing machine
Not working
Washing and Spin but 1 minutes working after stop please help me
Without more information hard to diagnose. However if it is a top loaded machine, please check the door is it available the peace of magnate which is provide a signal that door is closed. This problem can occur due to loos that peac of magnate on the door.
Ok I fix but led sacit bord some time working but some time not working
What if it's not even washing or rinsing or even spinning?
Might be bad spinning motor. Or the condenser
Onida top washing machine Spin running only water drain ok but motter not working pls video problem
Try this video
th-cam.com/video/R__VMKuJg00/w-d-xo.html
I have LG fuzzy logic 8 kg washing machine. at time remaining 30 min whole machine suddnly vibrating.and then stop. why ? can help me out this issue?
Machine vibration could occur due to cloths twisting during the spinning. Just untwist cloths and start again the machine.
Biro iwant diskas with how to do same w ork