I picked up one of these lights recently after seeing this video, months ago. Fortunately, I did NOT wire mine on the outside of my razor tour pack. I picked up some grommets at my local hardware store, drilled an appropriate hole behind the passenger seat pad just below the top edge, another hole in the front near the bottom of the lower section of the pack... disassembled the connector, fed it thru the holes, used the mounting tabs and tie wrap from the light kit, and it came out nice and neat, internally wired and water proof
Have to put on lights on king trunk on my victory same one that is used on a harley ultra if their 700 lbs and over that’s i big bike to lift don’t drop it at gas pump or hope goes the other way instead in the pumps crash bars and one of the pipe saves on your saddle bags
The shame they didn’t put the wire down lower where you could have the option to poke a hole in remove the pins put it through the hall run it up the top down the side out the bottom see my tour pack I bought aftermarket I put a second hole in the base for wires to go through get me another rubber grommet show it we need to pass to there also I don’t even have to pass it through there and pass to the other one and just tie into what’s inside my tour pack because I have a light on my rack and also go to the rear so I can go inside there that would be neat
How has this held up in the long run? Still look good? no moisture getting in? Also....does the backrest cover most of the wire that is on top of the tour pack right by the LED? It was hard to tell, but looks like it hid most of it. I really like the idea behind this particular light because its up high and visible.
@@rbljackson yeah, it is pretty well covered up. I’ve removed it just because I had so many lights on my bike and I wanted to cut back.. but yes it worked just fine.
I like the looks of this light, but not the exterior wires portion. Did they mold the wire location on the back of the light so that external is the only option? Thanks.
Anyone else have a problem with the sync? They all work great but the dash indicators are reacting as a light is out. Rapid bling on road king 2019 after several attempts to snyc
Try these Note: If turn signal indicators on the dash flush too quickly, refer to A or B below. Al I. Disconnect bottery negotive for at leust I minute, then reconnect it 2. Turn innition switch off-on 3. Activate left turn signal for 4 or more Flashes 4. Activate right turn signal for 4 or more Flashes OR B I. Turn ignition on 2. Activate hazard linhts for 10 Flushes 3. Deactivate hazards 4. Activate hazards for 10 Flashes 5. Deuctivate hazards
I'm sorry....love the CD products. However not this install. Do you think that drilling a hole, for the wire to pass thru the lid is doable? Would the light cover the hole? Then you can route the wire down the hinge and out thru the grommet with the other wires. Will be far more professional looking.
I don't think it would cover the hole.. might be a way, I'm sure you could secure the wire closer to the hinge area or route it a little different than I did but either way it's all covered up with the back rest other than when the lid is open. I think I left more than I needed for slack also but I just didn't want to have to worry about it getting pulled out or something.
I know this is a new reply for an old post but,, I just did an internal install for this. I have a razor tour pack and I hid the holes behind the passenger seat pad....easy to do.
I appreciate your videos. It gives me a chance to think through what I want to do or don’t want to do with my bike. I’ve done about half of what I see you doing on your bike. This particular product is something I think I will pass on, but I still appreciate the video because it helped me make my decision. Thank you.
Touring Midwest I think for me, since I travel with something on my luggage rack quite a bit, the fact the light would be obscured is one issue on this one for me. Probably the other issue is the awkwardness of the wire and trying to make sure it doesn’t get crimped by the lid closing. With my “luck”, I’d clip that thing in two after closing my lid twice. I watched your vids before on the tail light and the fillerz and I went out and bought my own. I think Custom Dynamix should give you some commission.
@@RevJay_Rides Na.. Custom Dynamics treats me pretty well but I definitely appreciate the kind words, I'm glad you've found these videos helpful. That's what its all about.. I've installed tons of lights on my bike and I don't always leave all of them installed but it creates content and shows viewers like yourself what it looks like, how it's installed, function, etc. I enjoy the heck out of it and also the conversations here in the comments.
Good video Andrew. I like the light bar and the presence it gives. More light to help you be seen. I'm all about that. I'm I surprised CD didn't find a way to hide the wire and give a quick connect option. Your videos are always entertaining and informative. Thanks Man.
![ลองสั่งของจากแอพ temu ถูกจริงหรอ?? [โกงไหมครับ ep.88 ] | DOM](http://i.ytimg.com/vi/RTcZSQTiDZw/mqdefault.jpg)
www.customdynamics.com/high-mount-tour-pak-led-motorcycle-brake-light
I picked up one of these lights recently after seeing this video, months ago. Fortunately, I did NOT wire mine on the outside of my razor tour pack. I picked up some grommets at my local hardware store, drilled an appropriate hole behind the passenger seat pad just below the top edge, another hole in the front near the bottom of the lower section of the pack... disassembled the connector, fed it thru the holes, used the mounting tabs and tie wrap from the light kit, and it came out nice and neat, internally wired and water proof
Another great video! Thanks for sharing!
Thank you and thanks for checking it out.
Have to put on lights on king trunk on my victory same one that is used on a harley ultra if their 700 lbs and over that’s i big bike to lift don’t drop it at gas pump or hope goes the other way instead in the pumps crash bars and one of the pipe saves on your saddle bags
The shame they didn’t put the wire down lower where you could have the option to poke a hole in remove the pins put it through the hall run it up the top down the side out the bottom see my tour pack I bought aftermarket I put a second hole in the base for wires to go through get me another rubber grommet show it we need to pass to there also I don’t even have to pass it through there and pass to the other one and just tie into what’s inside my tour pack because I have a light on my rack and also go to the rear so I can go inside there that would be neat
How has this held up in the long run? Still look good? no moisture getting in? Also....does the backrest cover most of the wire that is on top of the tour pack right by the LED? It was hard to tell, but looks like it hid most of it. I really like the idea behind this particular light because its up high and visible.
@@rbljackson yeah, it is pretty well covered up. I’ve removed it just because I had so many lights on my bike and I wanted to cut back.. but yes it worked just fine.
Do u know wire diagram by any chance for a 2006 Electra glide 2014 tour pack on it brake light signal work but I can’t get the daylight to Stan?
I don't but I'm sure they have install instructions on thier web site. Otherwise they are very helpful over there so you should give them a call.
I like the looks of this light, but not the exterior wires portion. Did they mold the wire location on the back of the light so that external is the only option? Thanks.
I think so. But you could reach out to CD for confirmation one way or another.
Great video but you talk too much in the beginning.
Thank you
Anyone else have a problem with the sync? They all work great but the dash indicators are reacting as a light is out. Rapid bling on road king 2019 after several attempts to snyc
Try these
Note: If turn signal indicators on the dash flush too quickly, refer to A or B below.
Al
I. Disconnect bottery negotive for at leust I minute, then reconnect it
2. Turn innition switch off-on
3. Activate left turn signal for 4 or more Flashes
4. Activate right turn signal for 4 or more Flashes
OR
B
I. Turn ignition on
2. Activate hazard linhts for 10 Flushes
3. Deactivate hazards
4. Activate hazards for 10 Flashes
5. Deuctivate hazards
Can it also be used on hogworkz slimline tourpak?
@@karenwilhelm126 I’m not sure if thatd work
Or not. Custom dynamics would be able to tell You if you give them a call
I'm sorry....love the CD products. However not this install. Do you think that drilling a hole, for the wire to pass thru the lid is doable? Would the light cover the hole? Then you can route the wire down the hinge and out thru the grommet with the other wires. Will be far more professional looking.
I don't think it would cover the hole.. might be a way, I'm sure you could secure the wire closer to the hinge area or route it a little different than I did but either way it's all covered up with the back rest other than when the lid is open. I think I left more than I needed for slack also but I just didn't want to have to worry about it getting pulled out or something.
I know this is a new reply for an old post but,, I just did an internal install for this. I have a razor tour pack and I hid the holes behind the passenger seat pad....easy to do.
Good videos. Some full shots in the dark from the sides/backs of all the light additions would be cool and helpful
Great idea, Thank you.
💪🏼💥
Well...dangit.....another purchase from Custom Dynamics. :) I like it!!
That is cool! I'm want that. And only that. Finally a light bar for turn signals and brake lights that I would use. Looking to order one now.
Nice looking light! I think having lights up high will help others notice you more.
It's a good quality light.. extra visibility for people is always a great thing for sure.
Good Stuff Andrew 👊🏻👍🏻
Thank you.
I appreciate your videos. It gives me a chance to think through what I want to do or don’t want to do with my bike. I’ve done about half of what I see you doing on your bike. This particular product is something I think I will pass on, but I still appreciate the video because it helped me make my decision. Thank you.
That's a great comment, I've never thought about it that way but it makes allot of sense, Thank you.
Touring Midwest I think for me, since I travel with something on my luggage rack quite a bit, the fact the light would be obscured is one issue on this one for me. Probably the other issue is the awkwardness of the wire and trying to make sure it doesn’t get crimped by the lid closing. With my “luck”, I’d clip that thing in two after closing my lid twice. I watched your vids before on the tail light and the fillerz and I went out and bought my own. I think Custom Dynamix should give you some commission.
@@RevJay_Rides Na.. Custom Dynamics treats me pretty well but I definitely appreciate the kind words, I'm glad you've found these videos helpful. That's what its all about.. I've installed tons of lights on my bike and I don't always leave all of them installed but it creates content and shows viewers like yourself what it looks like, how it's installed, function, etc. I enjoy the heck out of it and also the conversations here in the comments.
Enjoy your channel, Hope to meet you at Paris Texas for the Bring It Home Parade on Oct 5th....... Cuttymon......
Thanks... unfortunately im not gonna be able to make BIH. It would be cool to have an opportunity to meet so many people though.
Good video Andrew. I like the light bar and the presence it gives. More light to help you be seen. I'm all about that. I'm I surprised CD didn't find a way to hide the wire and give a quick connect option. Your videos are always entertaining and informative. Thanks Man.
Thank you.
Will this work on a 2014 Street Glide Special with a tour pack? The trunk doesn’t have any lights on it but we would like some.
I would think so..
Been thinking on this Andrew, but not sure if it will work as I run a polar bear on my tour back luggage rack. .lol
That might get in the way frosty lol
@@Touringmidwest ikr...hahahahaha
You going to Paris for bring it home2019? I am leaving at noon on Wednesday. Rubber side down and let the miles roll on
No, was hoping to but it's not going to work out for me.
Hey buddy, what’s the part number of that split cable you put in between the original harness? Thx.
No Clue man, sorry
Best bet is contact Custom Dynamics for it, since it is included in the light kit...
Looks good!
Going to check it out at Custom Dynamics!
Thanks!
No problem... thank you.
As always a great “how to” video. Looks awesome and safer to be seen. 👍🏼 👏👏👏 😎
Very kind, thank you.. I have a couple more cd installs coming in the near future.. already recorded, still need to edit.
I love their products. My RGS is lite up with CD lights mostly thanks to You. Great channel and am looking forward to your next installs. 👍🏼
Thanks For Video
Thank you for watching and leaving a comment.
Looks good man
Thank you .. it's getting to be allot of light lol. Overkill but its content so I just keep adding more lol... do it for the views.
Nor a fan of how the wire is so exposed. Think I'll pass on this light