Thankyou so much for your series of videos on this engine. They have helped demystify the engine and it's maintenance needs. Very much appreciate the detail and professionalism here.
Thank you for your guidance and encouragement. I am a new boat owner with a low hours KAD-32. Unfortunately, the maintenance history is quite poor. I plan to service the heat exchanger, oil cooler and after cooler. Your videos have afforded me some needed confidence to perform the work myself. Tusen takk!
Hi svend.. Thank you for your videos.. I have the same engine and have discovered a fuel leak from the lift pump.. I'm looking forward to this part of your overhaul to see if you talk about the lift pump and show its removal etc!
Hi there, Can you please tell me the pressure setting of injectors? Thoses working for bosh tells 240 bar, thoses working for volvo penta tells 260, I tried 240 bar, the engine smokes a lot, i find gasoil in the surface of the sea after running the engine. I did not try 260 bar yet, I m realy confised Thank you. My engine is Tamd41a
Before un-mating pieces...might be useful to make a WITNESS LINE ...ACROSS the mating parts. Then...there will be NO QUESTION as to HOW they RE-ATTACH.
On my boat I had a seal fail on the outdrive and this allowed seawater to get inside the flywheel housing. This in turn caused the rear oil seal to get damaged by the rotating rusty crankshaft. For me it mea t engine out, then a Skf speedysleeve install. I have yet to install the sleeve but am told the end of the crank must be cleaned of debris before installing the sleeve. I will do my best to video the install, but it won't be as polished a production as these fine videos. The sleeve is due to arrive in 1 weeks time. Hope it helps someone.
Thankyou so much for your series of videos on this engine. They have helped demystify the engine and it's maintenance needs. Very much appreciate the detail and professionalism here.
Thank you so much, after searching loads of videos I found you, very informative and I got to take the cooler apart confidentiality, 100%
I'm in Ireland and find your videos very helpful. please continue with English language Episodes thank you.
Thank you for your guidance and encouragement. I am a new boat owner with a low hours KAD-32. Unfortunately,
the maintenance history is quite poor. I plan to service the heat exchanger, oil cooler and after cooler. Your videos have afforded me some needed confidence to perform the work myself. Tusen takk!
Another very good video. I have recently bought a boat with a TAMD41B and will learn a lot from your videos.
Very informative,well filmed, keep them coming!!
about to tackle this job today so thank you very much for the lesson, love your series has been very helpful. Looking forward to more episodes.
Thanks so much for your comments. Much appreciated!
Good day, i have one question if you have time for answer?! Other cooler cover you cant remove?! Side where should be Zn protector?
838928 is the part number for the square headed plug/zinc/anode. Don't think that was ever shown.
Hi great vids thanks - could the oil cooler be a reason for no oil up at the rocker shaft?
Hi svend.. Thank you for your videos.. I have the same engine and have discovered a fuel leak from the lift pump.. I'm looking forward to this part of your overhaul to see if you talk about the lift pump and show its removal etc!
Thank you for making theses, very helpful
This is a huge help. Thank you
Hi there,
Can you please tell me the pressure setting of injectors? Thoses working for bosh tells 240 bar, thoses working for volvo penta tells 260,
I tried 240 bar, the engine smokes a lot, i find gasoil in the surface of the sea after running the engine.
I did not try 260 bar yet,
I m realy confised
Thank you.
My engine is Tamd41a
Before un-mating pieces...might be useful to make a WITNESS LINE ...ACROSS the mating parts.
Then...there will be NO QUESTION as to HOW they RE-ATTACH.
WHAT!? I can't HEAR you very WELL?
Could you clean the water side the same way you did the heat exchanger,ie not remove the insert?
Kjenner du bra til tmd 31 av penta??
4 selyndret
I like your videos; any plans for circulation pump and thermostat housing maintance?
Hej fråga det kommer vit rök från avgasröret ? Vad kan det vara
Hello i have a engine AD 41 PA i would liké to know how to amorcing a New turbo tks
Great Video again, thank!
Must be time to release another one. From Western Australia
Really good stuff. Thank you.
Any advice on how to bleed the cooling system?
Great video thanks
what materials did you use to build your frame for the motor?
The frame is made of wood....
I have pictures i could send to you, if you have a mail adress, or maybe on facebook?
Svend is there any plans to do front and rear main crankshaft seals or is this a simple thing to figure out ?
On my boat I had a seal fail on the outdrive and this allowed seawater to get inside the flywheel housing. This in turn caused the rear oil seal to get damaged by the rotating rusty crankshaft. For me it mea t engine out, then a Skf speedysleeve install. I have yet to install the sleeve but am told the end of the crank must be cleaned of debris before installing the sleeve. I will do my best to video the install, but it won't be as polished a production as these fine videos. The sleeve is due to arrive in 1 weeks time. Hope it helps someone.
Its similar in a engine d4 225?
where can i get a magnet coupling for the compressor
Thank you
Hi, very useful video so well done. Any chance you also worked through a ms4 gearbox?
I can't find episode 4. Manifold?
Thank you
Brilliantly clear!!!!
When is the next video coming? Or are you out cruising already and don't have time to edit/upload...
Thanks sir
Good
You should invest in a power tool.
Great video , but loose the music !
Bad Engine Designs in the first place,,way too many gaskets to replace..
肝心な物があるでしょ
L
I just watched you use a hammer on a ratchet wrench. I don't care about anything you say from this point forward.