Volvo Penta 290 Dp-A Dp-B outdrive Sterndrive Removal

[@aquaholictherapy463]

Thanks for the straightforward video!!

[@Bobssecondhand]

Well done Ryan! This helped alot. All the best from Sweden =)

[@MrLinezzz]

such a great video. without it, it would have been impossible for me to get that thing off 💪

[@pfcpatsy]

Great video and explanation. Exactly what I needed. Thanks guy. 👍

[@mikaeljansson280]

thanks👍 you have done this before I notice

[@Matthew-zd8qw]

I cannot get the upper 2 pins out won't budge

[@jonstevens2471]

Same here! And mine had the big splash well deletion in hull so no slide hammer access

[@dominickentrekin598]

I am replacing the Bellows and gimbal bearing on this exact stern drive. My problem is how do you remove the shaft after the drive comes off? Great video by the way!

[@dylanholzenkamp1745]

Have any videos of doing the primary shaft?

[@1stinsonguy]

Ryan, do you have a photo of an installed fuel pump on a AQ205A engine? Thanks.

[@josehechavarria2003]

Thanks for your video

[@lorenmaly1637]

Badass! Thank you!

[@stefcampagna2321]

Awesome video. Thks !

[@randallweichbrodt1582]

Thanks Ryan!

[@jeremyhale4137]

How do you put it back in!??

[@ThomasKabalt]

Dat vroeg ik mij ook al af haha

[@ryanvanlandschootd.c.671]

Any advice for removing the shift cable connector ( little metal piece at the end of the threaded rod)? Mine will not break loose even with vice grips holding the threaded rod.

[@Off2Fly737]

Great video! Exactly what I needed to see.

[@ManuelDiaz-fm2dv]

Como puedo sacar el pasador que agarra el brazo donde coge el cable del timón

[@goproexplo9290]

Nice Video. I need some help, i got the leg off 100%, when i took the pin out for the trim rams, one ram compressed and the other lengthened. I felt to see if i could push and pull and they seem solid, Why has this happened? How do i get them free to move to line them up? Thanks

[@mikeshanaberger7503]

Thank you!

[@georgebernero4634]

How did you remove the trim cylinders

[@mvperseverance]

I've got that same drive, but my water intake hose is really pinched. Where it connects to the drive itself, it comes off that point and goes starboard before it bends back to the port side where it goes through the transom. Seems like a silly design, or I got the wrong hose. Any suggestions?

[@travisconner1581]

Never comes apart that easy 😂

[@terryjackybishop8995]

I need to have my drive rebuilt

[@javierzerozeroseven9959]

WOW In less than 10 minutes.

[@joneich1591]

That extension really made my life a lot easier.. 😜😅😅😅😂😂😂👍

[@CorriG]

Thank yoooouuuuuu...... 😅😅😅

[@grasscutter88]

I expected it to just fall down when he pulled the main hinge pins out.

[@justingeturgun]

What happens when your hinge pins bolts are stuck lol

[@seanstewart9722]

Any progress on this? I’m running into the same issue.

[@turboed00SI]

I had to heat mine up, be careful not to go too hot though lol

[@hedgepethracing9590]

Good looking out on the video, I'm praying someone greased my Monday morning, Volvo drive...

[@garypeatling7927]

Ok but using gun to undoe seized bolts is silly , Seen threads torn out blow lamps and oil more sensible

[@jimmyglidewell1604]

THANK YOU 🙏

[@Drgoldthumb]

Thank you!!!