@Amd detailing Isn't that bad for the window/glass to develop so much heat like that? Won't the inner layer PVB warp? I've never seen all this heat buildup before. Maybe using a random orbital would've been better? Well regardless, finished product looks great
@@DetailingJourney its intended to use with heat that's why he's able to remove scratches, if you're using cerium oxide as compound then you should read instructions one of which is heat glas and cool it down or stop betweeen passes, glass won't crack that easily you heat it up gradually in other words pay attention to what you're doing...
Man, I think this much heat will warp the glass or you get distortions. Maybe ok for the back window, but I will never do it on the windshield. But as he said in the video. His car - his rules.
that is why it has been shown that glass cannot be broken just like that during polishing, and in order to remove major damage, the glass must be well heated and cooled in time in order to have an effect.
@@chlama wrong, nothing less warp or distotions than from normal usage (sun hits windshield during summer). after years you get some warpage. So eyes during driving doesn't focus so close on glass itself rather in distance in comparsion if you have bad scratch on windshield eyes will focus on that from time to time and that thing bothers much...so balance what's best for you having clean glass or scratch
Staklo je veoma zahtjevno za polirati moras dobro ga ugrijati i znati kad ga treba ohladiti a da ne pukne pritisak na masini mora biti nekih 10/15 kila ,rotaciona masina obavezno posebna pasta i poseban filc za poliranje stakla ide. Jeftinije je no u zamjensku staviti nego polirati iskreno
Great video, what kind of support did you use for the pad?. I have a couple of lines of distorcion in the windshield, can I remove them with this product? Regards
My car is new and I have scratches and swirls in my glass after trying to polish out indstrial fallout, will heating the glass cause any damage or change the texture of the glass?, also which machine should I use?
@@Amddetailing Thank you. I am thinking about cutting the 3" CarPro glass pad into 1" for some micro repairs using a small rotary like Rupes ibrid nano or Griots new GR3.
@@Amddetailing but this can damage the glass you must spray water all the time you polish the glass and every bass you check the heat with your hand never get over heat and this is my 15 years knowledge it take from 10 to 15 min to get glass full polished with alot of water and no overheat but in the end good job and great results thank you
@Amd detailing Isn't that bad for the window/glass to develop so much heat like that? Won't the inner layer PVB warp? I've never seen all this heat buildup before. Maybe using a random orbital would've been better? Well regardless, finished product looks great
Agree, too much heat generated. He's lucky the glass didn't crack
@@DetailingJourney its intended to use with heat that's why he's able to remove scratches, if you're using cerium oxide as compound then you should read instructions one of which is heat glas and cool it down or stop betweeen passes, glass won't crack that easily you heat it up gradually in other words pay attention to what you're doing...
Man, I think this much heat will warp the glass or you get distortions. Maybe ok for the back window, but I will never do it on the windshield. But as he said in the video. His car - his rules.
that is why it has been shown that glass cannot be broken just like that during polishing, and in order to remove major damage, the glass must be well heated and cooled in time in order to have an effect.
@@chlama wrong, nothing less warp or distotions than from normal usage (sun hits windshield during summer). after years you get some warpage. So eyes during driving doesn't focus so close on glass itself rather in distance in comparsion if you have bad scratch on windshield eyes will focus on that from time to time and that thing bothers much...so balance what's best for you having clean glass or scratch
I thought the rotary tool was doing the music😂
Next time try Sonax product for that, much faster cut.
So using the rotary is the key to this ? I tried with a DA and didn’t get the best results. A lot of pressure as well ?
Try rotary DA the machine is too weak for glass
Da li moze video kako ocistiti nebo u automobilu? 😃👍
nije to nauka cista mikrofiber krpa imas pjenu kupit po marketima ilo gdje se pravi boja za auto ostavis pjenu minut i cistis pozzzz
Da li bi htio da nam opises rijecima ono sto smo vidjeli u videu...pozz,kanal je stvarno super...
Staklo je veoma zahtjevno za polirati moras dobro ga ugrijati i znati kad ga treba ohladiti a da ne pukne pritisak na masini mora biti nekih 10/15 kila ,rotaciona masina obavezno posebna pasta i poseban filc za poliranje stakla ide.
Jeftinije je no u zamjensku staviti nego polirati iskreno
i get the same result with a sledgehammer and have the window replaced 😁
Hahahaha good 🤣🤣🤣🤣🤣
Can this techniques good on water spot on window glass as well.
For this, you can spray and wipe liquids from various manufacturers, and you can also try citric acid
Great video, what kind of support did you use for the pad?.
I have a couple of lines of distorcion in the windshield, can I remove them with this product?
Regards
In what country ceri glass products
Which product you r using for glass?
Carpro ceriglass
Great video! Terrible music..
In what country i can got ceri glass
Por favor:
Me puedes recomendar un remedio para proteger los laterales de mi auto de los portazos de los vecinos del parking compartido? Gracias
BCN
English please I do not understand you
My car is new and I have scratches and swirls in my glass after trying to polish out indstrial fallout, will heating the glass cause any damage or change the texture of the glass?, also which machine should I use?
Please reply, I need help
Send pm in mesinger Alen Tataragic
Super,kad sam vidio Bosnalijek,skontam nase gore list hee.. Znaci rucno nista,bez masine
Which pad you used for this ? 👍👍
Carpro pad for glaaa
Just a note, don't try it at home and leave it to professional like AMD Detailing.
What was your speed setting?
1800rmp
@@Amddetailing Thank you. I am thinking about cutting the 3" CarPro glass pad into 1" for some micro repairs using a small rotary like Rupes ibrid nano or Griots new GR3.
@@aquarianuw no you must use big rotari maschine
@@Amddetailing the scratches I am going after are on the bottom of the glass. Why is a big rotary necessary?
you have to have a pressure on the machine of about 10 15 kg and you can't do that on a small scale
Did you spray warm water on the glass?
Clean water and finish alcohol
I don't know what it is about the E91 but the rear windshield gets absolutely destroyed....
I have the same problem, much much worse scratches than yours
@@awdaltima2 bmw uses softer glass
Ako nije tajna, na koliko rpm radi masina? Lp
Ugrijem staklo sa 1500 i poliram sa 2000 2500 do 3000
@@Amddetailing hvalaa na odgovoru :) pozdrav
@@zlajabrkic660 nista sve najbolje
How deep scratch can it be removed?
Povrsinske moze duboke bez brusenja kamenom ne moze😉
@@Amddetailing auu dobro je srpski. Na koji kamen misliš?
@@ivanncee ma oni za brusenje stakla(dijamant) ali brate to nebi preporucivao nikome jer tad je vjerovatnoca da ce puknuti staklo 100%🤣
@@Amddetailing mene nervira jer sam kupio auto sa oštećenjem od brisača. Pa bih probao to da ublazim
why is it smoking
Too much heat, not good advice. Look other videos, they always warn about not too much heat. It must be warm to touch, but not heat
Too wrong this glass heat
in order to burn deep litigation the glass must overheat
@@Amddetailing but this can damage the glass you must spray water all the time you polish the glass and every bass you check the heat with your hand never get over heat and this is my 15 years knowledge it take from 10 to 15 min to get glass full polished with alot of water and no overheat but in the end good job and great results thank you