It is good way of SOIC and QFP package soldering indeed. Small knife tip also works well for that. Just soldered LM324ADT in SOIC-14 package in a way as displayed here. Super clean soldering in result.
will this solder paste increase the short circuit possibility between pins? My board have arcing when power up, suspected to be short circuit pins. Hope to have your advise, thank you!
Andrew Horton It’s not “hate”, it’s legitimate criticism. This guy is better than a total beginner, but his technique is not great. In particular, he goes back and reworks joints over and over, which actually makes them worse, since the prolonged heating causes a) oxidation, and b) increased dissolving of the base metal (of the component lead and the PCB pad), which changes the composition of the solder in the joint. These two things together make bridges and other flaws much more likely to happen. Honestly, what this guy is exceptionally skilled at is filming the process, not actually at the soldering itself! There are better tutorials on TH-cam (e.g. John Gammell, PACE Worldwide, and EEVblog) in terms of teaching you the skills.
Ok I have been practicing with a kit that I bought and I'm doing it with the heat gun but I think using the iron it's faster more accurate thank u for this video
It's ok to do this if you cover everything in flux yourself. If you're using flux-core solder (without separate flux) and you try to use solder already on the iron to make a joint, it'll probably give you a dry joint.
@@neocortez9254 im start building and modifite flashlight now for personal use and sell to close friend and family.. i dont have knowledge about electronic circuit but i like soldering so flashlight seem a great idea to start soldering.. buy a flashlight host from convoy brand and install the driver and led myself.
Make the legs drawn in solder, connect them all together, and then use heatgun and soldering machine to liquify the solder. After that poke the chip to a side.
saiiiiiii1 Tip shape and flux. Just don’t reheat the same joints over and over like he does - that causes oxidation and increases the risk of bridges. (The very first joint he does in this video is an example of this: it was perfect on the first try, and yet he went back at it over and over, and the extra heat caused oxidation and a bridge.) Look at the EEVblog and Ganssle videos on drag soldering for a much better explanation.
Flux is used to chemically reduce the metal oxide layer on top of the parts to be soldered and therefore contributes to a solid and clean solder joint. In practice, almost no soldering application in electronics would be possible without it. The commonly used halogen-free rosin flux , if inhaled, should be a bit less toxic than passive smoking.
@@TEMA1970 Спасибо, но я уже разобрался в этом вопросе. Похоже сейчас некоторые из лучших сейчас это такие флюсы как СОЮЗ, Орбита, МПЛ-151, ESF-373, NRK-373-Expert. На TH-cam канале RusFlux Info есть обзоры и таблица сравнения всех основных флюсов, и на канале Романа Гребеникова тоже есть полезные видео на данную тему.
pretty horrible lol... just put some solder paste(before or after as long as you don't put too much) on the pins first then place the chip on there and from outside add a little bit of flux and use the heat gun to heat up the connection and just use tweezers for minor adjustments to place the chip in place. A professional should have done it within 30 seconds. lol Note: for solder tip use ETKN type is much easier than this and is a lot easier to remove solder bridges from any components on board. I personally use ETKN for 97% of my work, the rest of 3% of when I have to deep clean some chips on board and the only option is the solder wick (for components such as CPU , North Bridge, on-board memory chip, ect).
Есть моменты, которые смущают. 1. Пинцет в пластиковом чехле. Конечно, так удобно удерживать микросхему, но это не обязательно. Нанёс флюс, поставил микросхему, и потом паяльником проходим по дорожкам платы не касаясь самой микросхемы, чтобы её не сдвинуть. 2. Сопля или мост. В Европе каплю припоя, соединяющую два ближайших вывода микросхемы, называют мостом, в России - соплёй (у нас вообще к соплям плохо относятся, если что-то плохое, значит сопля. Воспринимайте это как шутку). С жала паяльника убирается капля припоя, но не об губку, а просто сбивается (лёгким ударом жала паяльника о какой-либо предмет. Но не забывайте о технике безопасности). Это основные проблемы/ошибки. Лично для вас могу прислать фотографию платы (circuit board) собранной (assembled) мной лично при помощи только паяльника. P.S. Воспользуйтесь Google Translate
Adam Jameel I am just saying what I saw in this video. And yes there is no doubt that this guy has poor soldering skills which are needed to be improved with practice. I have 18 years of SMD soldering experience on the basis of which I made that comment. Why are you getting offended. I wish this guy the very best of luck and i will be more than happy if I could teach anyone. I can say no more..!
finally, found a video worth to watch at 3 am,
4am lol
Soooooo beautiful!!! The music! The camera work!! And of course, the soldering, great video, helped me in a project, thanks!
I could not see the video because of the tears I had to cry while listening to your weltschmerz music :(
This guy’s soldering technique is very easy to get to any level of workers or student
Good job man! I like your style. Thank you! :)
Glad you like it :)
@@Androkavo
Which software used for coading
Best soldering man ever seen, Good job
Keep it up, deserve a Million subscriber.
Very nice videography.
7:25 a rebel pin!
dont worry still work
This was by far the best video of many I have seen on the subject. Thank you!
PS: I would love to know how you magnified this footage. It is amazing!
Just open your video editor and speak the word "Enhance".
He used a microscope with recordung function
Que satisfacción dar ver estos trabajos 😌
Oddly satisfying!! Keep making more videos
It is good way of SOIC and QFP package soldering indeed. Small knife tip also works well for that. Just soldered LM324ADT in SOIC-14 package in a way as displayed here. Super clean soldering in result.
Sou seu fã, quero aprender muito com vc, obrigado
art!
Thank you so much for your clear videos. I wonder that; which camera do you use for your videos? I love macro videography. Thank you inadvance.
Excelent!
what is the temperature of your iron ?
That pump bottle is nice
Nice soldering job
Most satisfying video
Awesome! Really awesome!
a new kind of ASMR
what kind of solder you use? goot tq-77 or tq--95? or others? and how to look deep into the cheap? are you using a magnifying glass?
Nice work
Это волшебно, респект и уважуха
Good job👏
@Androkavo What microscope did you use?
excellent guide,
Very very nice soldering
MUITO BOM, VALEU IRMÃO...
The Bob Ross of soldering
Whoever thought of that scalable pad layout deserves the Nobel Peace Prize.
very nice video thanks
beautiful..
amazing
Мастерство уровня Бог)
*Bravo et merci !*
what soldering iron set do you used? where to buy?
Good work
Amazing
will this solder paste increase the short circuit possibility between pins? My board have arcing when power up, suspected to be short circuit pins. Hope to have your advise, thank you!
just wipe it of. But normaly not
@@TerraToastBrot thanks for reply. We found out our soldering paste will release conductive material after melting
where can we purchase these practice boards ?
you deserve trillion likes !!!
BRO WHICH CAMERA DO YOU USE
:)
Which camera do you use to record?
What is model of microscope you used ?
What do you use to clean the flux...is it just isopropyl ?
Was this solder job done with lead free or 60/40 solder? You made it look easy! Nice job.
Sure, with lead free you need higher temperature (350~400°C)
Androkavo, Sure, what? The question was is it lead-free or 60/40 solder. You answered, "sure". ??
@@flashcraft
Can you read though? 😊
@@Androkavo
Question: are you aware of good solder on Aliexpress? Or, in your experience, there simply no good solder on there?
@@flashcraft sure that it look easy, with lead free you need higher temps, so we can assume it is leaded solder dont you think???
What tempreature do you use?
Ignore all the hate bro I like your style and it’s helped me out with some of my project, keep it up, you’ve gained a sub from me 😀
Andrew Horton It’s not “hate”, it’s legitimate criticism. This guy is better than a total beginner, but his technique is not great. In particular, he goes back and reworks joints over and over, which actually makes them worse, since the prolonged heating causes a) oxidation, and b) increased dissolving of the base metal (of the component lead and the PCB pad), which changes the composition of the solder in the joint. These two things together make bridges and other flaws much more likely to happen. Honestly, what this guy is exceptionally skilled at is filming the process, not actually at the soldering itself!
There are better tutorials on TH-cam (e.g. John Gammell, PACE Worldwide, and EEVblog) in terms of teaching you the skills.
@@tookitogo thank you
Ok I have been practicing with a kit that I bought and I'm doing it with the heat gun but I think using the iron it's faster more accurate thank u for this video
Where can i get such pcb for specific number of pins. ?
very good
beauty
Beautiful soldering tho
Музыка - класс! Работа - мастерская!
Anyone know where to get the IPA cleaning alcohol pot from? looks ceramic?
nice idol,,,,
Androkavo congratulations, beautiful pictures. Could you do SMD desoldering - QFP100 Package?
Hotgun. Or Solder Remover Wick Wire. As an option, you can buy it (or them), in Aliexpress.
Great
Cool
Sir, im a beginner in this case. May i know what type of soldering tip and the solder size you used in this video?
Bevel /hoof tip and any size is ok as the tip is loaded with solder and not point to point soldering
looks like they are usine a hoof/bevel tip in this video, if you have a Pinecil that would be the BC2 tip in Short or normal length version.
0:46 looks easy but the hardest part...
Por favor como compro essa pasta é esse ferro de solda
pt.aliexpress.com/item/MEC-NICO-MCN-UV80-Ferro-de-Solda-No-Clean-Pasta-de-Solda-Flux-Soldagem-Fundentes-Cole/32943417017.html?spm=a2g0s.13010208.99999999.266.3e033c00Dlhmtn
May I know the name of the background music?
'Undercover Vampire Policeman' by Chris Zabriskie
Music makes me think of pokemon games
Очень интересно. Спасибо
totalne partactwo!
To znaczy? Co on zrobił nie tak?
When I drag the pins like that on these I always end up with bent ones
Really super, but removed trick????
@0:55 , he already had a solder on soldering iron right??
yes, otherwise it wouldn't work.
It's ok to do this if you cover everything in flux yourself. If you're using flux-core solder (without separate flux) and you try to use solder already on the iron to make a joint, it'll probably give you a dry joint.
classmaster
this video is so addict... make me feel want to solder but dont know what to start with because dont know what to solder or build..
take apart old electronics, remove the ic and resolder em back
@@neocortez9254 im start building and modifite flashlight now for personal use and sell to close friend and family.. i dont have knowledge about electronic circuit but i like soldering so flashlight seem a great idea to start soldering.. buy a flashlight host from convoy brand and install the driver and led myself.
did anyone realise this music is 'Logan you are my hero'
Great tutorial but You should give details of your tools also...
By alcohol, you mean isopropyl alcohol?
Very good.
Show us how to desolder this chip.
Use heat gun to heat up the chip and all legs, then lift. Install the new one like in video. :-)
Make the legs drawn in solder, connect them all together, and then use heatgun and soldering machine to liquify the solder. After that poke the chip to a side.
@@emremutlu44
I don't think the first step is needed...
Why are there no bridges created between the pins and why doesn't more solder go onto the pins?
saiiiiiii1 Tip shape and flux. Just don’t reheat the same joints over and over like he does - that causes oxidation and increases the risk of bridges. (The very first joint he does in this video is an example of this: it was perfect on the first try, and yet he went back at it over and over, and the extra heat caused oxidation and a bridge.)
Look at the EEVblog and Ganssle videos on drag soldering for a much better explanation.
@@tookitogo
Also, I guess, because solder tends to stick to metal parts, similar to how water (liquid) surface tension works.
Maxim C. It only does because of the flux. Without flux, the oxidation causes it to blob up and refuse to flow and wet the joint.
@@tookitogo
True. Thanks.
You are an artist with a soldering iron and flux.
Flux is used to chemically reduce the metal oxide layer on top of the parts to be soldered and therefore contributes to a solid and clean solder joint. In practice, almost no soldering application in electronics would be possible without it. The commonly used halogen-free rosin flux , if inhaled, should be a bit less toxic than passive smoking.
It's not good to inhale, you can get a fume extractor or at the very least a fan to blow the fumes away.
please , model, price, link of you microscope, thanks
goo.gl/7kUgFD
thanks.
how to do it with 88i6745-TFJ1
isn't it better to tin the pads before placing the chip.
Скажите пожалуйста название камеры?
Flux is still between the pins, used a stronger solvent.
🤣
有強迫症的人看了好療育~
ni hao
I am an electronics engineer and I'm hard right now
this is so sad ;(
Can't believe they did that to it :(
look how they massacre my boi ;(
Flux must cost a fortune where you are from.
a wise man once said, you should clean your pads first.
He should use solder paste then a heat gun it will give best results than this
ฝีมือยังไม่ชำนาญ
poor quality of the solder flux, but nice sharp video
mechanic is no 1 in solder flux
Don't tell me... You're gonna say Antech NC-559? pff
флюс у тебя плохой
Почему Вы так считаете?
@@MaximC Такое норм пропаивается с первого раза, а не маструрбируется
@@user-wl5ws8dp1r
А какой флюс хороший/подходящий?
@@MaximC лти 120 пойдет и температуру прибавить чуть
@@TEMA1970
Спасибо, но я уже разобрался в этом вопросе. Похоже сейчас некоторые из лучших сейчас это такие флюсы как СОЮЗ, Орбита, МПЛ-151, ESF-373, NRK-373-Expert.
На TH-cam канале RusFlux Info есть обзоры и таблица сравнения всех основных флюсов, и на канале Романа Гребеникова тоже есть полезные видео на данную тему.
Kicsit gyakorolnod kellene a forrasztást. Ne sajnáld a folyasztószert. AMTECH NC-559-V2-TF
С будуна хрен запаяешь!
The guy has adequate tools for welding jobs! But lacking technique for a better job.
pretty horrible lol... just put some solder paste(before or after as long as you don't put too much) on the pins first then place the chip on there and from outside add a little bit of flux and use the heat gun to heat up the connection and just use tweezers for minor adjustments to place the chip in place. A professional should have done it within 30 seconds. lol
Note: for solder tip use ETKN type is much easier than this and is a lot easier to remove solder bridges from any components on board. I personally use ETKN for 97% of my work, the rest of 3% of when I have to deep clean some chips on board and the only option is the solder wick (for components such as CPU , North Bridge, on-board memory chip, ect).
Sorry to say but Poor soldering skills
It will be better if you can explain or show your super-master soldering skills
Есть моменты, которые смущают.
1. Пинцет в пластиковом чехле. Конечно, так удобно удерживать микросхему, но это не обязательно. Нанёс флюс, поставил микросхему, и потом паяльником проходим по дорожкам платы не касаясь самой микросхемы, чтобы её не сдвинуть.
2. Сопля или мост. В Европе каплю припоя, соединяющую два ближайших вывода микросхемы, называют мостом, в России - соплёй (у нас вообще к соплям плохо относятся, если что-то плохое, значит сопля. Воспринимайте это как шутку). С жала паяльника убирается капля припоя, но не об губку, а просто сбивается (лёгким ударом жала паяльника о какой-либо предмет. Но не забывайте о технике безопасности).
Это основные проблемы/ошибки. Лично для вас могу прислать фотографию платы (circuit board) собранной (assembled) мной лично при помощи только паяльника.
P.S. Воспользуйтесь Google Translate
Adam Jameel I am just saying what I saw in this video. And yes there is no doubt that this guy has poor soldering skills which are needed to be improved with practice. I have 18 years of SMD soldering experience on the basis of which I made that comment. Why are you getting offended. I wish this guy the very best of luck and i will be more than happy if I could teach anyone. I can say no more..!
18 years of SMD soldering experience, but don't know explain what's wrong or any advice. I can say no more..!
Tariq Mehmood you're a fucking idiot