Atem Mini - Live Streaming Audio
ฝัง
- เผยแพร่เมื่อ 1 ต.ค. 2024
- In this video I'll show you how to get great audio to your live stream from the ATEM Mini. This video switcher is going to be a great way for lots of people to start live streaming, it's a 4 channel video switcher with a video interface to the computer built in. It also has a lot of really great audio features!
LINKS:
Atem Mini: amzn.to/3a7mOvr
Atem Mini PRO (live streaming built in) amzn.to/38yH9cV
Atem Mini Extreme (more inputs and 2 outputs) amzn.to/384KIXP
Dual 1/4" to 1/8" stereo audio cable: amzn.to/37A8XGY
Dual XLR to 1/8" stereo audio cable: amzn.to/2UVuYgL
Atem Mini: amzn.to/2tbWxa6
USB-c cable: amzn.to/30mJoYc
Canon R800 Camera: amzn.to/30bLWYU
Nice tripod for following someone on stage: amzn.to/2Rcl6vA
Computer for live streaming: amzn.to/2sewNJO
VIDEOS:
Crowd Mics for Live Streaming: • Crowd Mics for Live St...
Live Vocal Processing: • Live Streaming Audio -...
How to use an Aux Mix: • Live Streaming Audio -...
Great streaming audio: • Live Streaming Your Ch...
CONNECT WITH ME:
Subscribe: www.youtube.com...
Facebook: / stephenballastmedia
Instagram: / ballastmedia
www.ballastmedi...
*affiliate links
Great info, thanks for this, Stephen!
Perhaps I missed it, but it would have been good to cover that the line input is unbalanced (Step down transformer is needed to avoid noise and headroom issues) and not +4dBu. So if you don’t use a pair of transformers, you need to keep the level down going in, then bring it up via the mixer. High pass is a good suggestion and I think you really should only use the limiter. Compression would be applied at the board.
Excellent information, cleanly presented. Wonderful work! Also, you're the first video I've found that shows how to change from Mic to Line level in the ATEM Control software.
This was exactly what I needed. I have a line signal and I was afraid to go direct into ATEM due to lag rumours, and my cheap Canon camera only has Mic levels in. Thank you!
Nice Job, Easy to understand. Explained well and also great template for compression/limiting and EQ. Thanks!
Hey Stephen! Thanks for this video. You've been a great resource in my streaming journey. I've learned a ton from you and appreciate it! So here is my current problem. I'm trying to monitor my audio from the headphone jack on my Feelworld F5 monitor and can barely hear anything. I have the monitor volume all the way up and have all of my audio setting as I think they should be and its so quiet still. Do I need to run a headphone amp between the monitor and the headphones? Or any other tips would be great. Thanks! Dustin
Can you help me with this question. I use Atem mini pro extreme ISO and I have connected Camera1 (BMPCC6K) to HDMI1 input on Atem, Macbook pro to HDMI2 input and USBc also to macbook. My Microphone is connected to Camera1. I attend Zoom calls and I record all inputs however the sound of the guest in Zoom call is not getting recorded to ATEM. I connect headphone to macbook to hear the guest, but I can't get their audio in audio and video files for HDMI1 or HDMI2. Can you help me understand how can I get the audio of the guest in zoom or another conference app on to ATEM recording.
first check the MacBook can send audio on hdmi, e.g. th-cam.com/video/5qZyGi8kWtM/w-d-xo.html
Hi I have a problem .. I use atem mini & OBS for my streaming setup. When I record my video streaming from OBS it sounds good with no problem, but when it started to “stream video” then I watch it from Instagram Live it has no sound ....
Hmmm, how are you going to Instagram? They don't officially support streaming from anything but the app. Are you using yellow duck? What are your audio settings in OBS?
Best explanation so far! Apparently, I will also need the 1/8 to XRL cable
And once again thanks, my new mini pro (to me, bought second hand for a good price) is now all setup :)
Thanks for the video. It's timely
Thanks for mentioning the update that corrects the sync issues! I'm about to order the mini pro but I had been 'hearing' issues with the sound sync with direct mic inputs. Now I feel better with the plan to use a boom mic connected to the mini pro.
Thanks again! So I have an Atem mini, mic in mic 1, and I'm live on TH-cam - How do I play audio from a video on my laptop without having to turn my mic and put it up against the laptop speaker?
How are you streaming? Is the laptop with the video the same as the computer you stream from? There are several ways to accomplish this. 1. if you are streaming with a program like OBS, you can play that video right from OBS. 2. You can send an HDMI output from the computer with the video to your ATEM mini and it will show up as one of the inputs, audio and all (turn on the audio from that input).
@@BallastMedia I have a laptop, a monitor, a camera. I'm using an HDMI splitter for a third monitor to display my screen. The camera in Slot 1 on the ATEM, Slot 2 is connected to my laptop, Slot 3 is going to the HDMI splitter. I tried turning the audio on slot 2 and 3. I didn't have any results. Would like to do this without OBS. Any help?
@@BallastMedia I figured out how to do it with OBS and OBS stream. But not while live with just my ATEM.
@@AndrewPatocchi You should be able to configure the laptop to output audio on the HDMI. Then turn that input on the atem on in the audio mixer panel of the atem. It sounds like it's a configuration on the laptop that you need to figure out to get audio routed to the hdmi.
You are one of the best teachers on TH-cam!
Blackmagic update available today that "Adds adjustable audio delay on the analog inputs on ATEM Mini models."
Much awaited feature!
Sir while using atem mini im getting audio first and video later.. there is a delay in video. So i adjusted the audio latency to 8frames even though video audio arent syncing.. please help. We are using panasonic ux90 and sony nx200
Great video! So if I'm just using audio from a Camera 1 mic I just turn Audio on in Cam 1 in Audio Control on the ATEM?
Correct.
Can you show us how the built in USB output produces a more compressed image compared to connecting a USB capture card to the HDMI OUT.
Once you compare the two side by side you will notice the built in USB output image is worse.
I haven't noticed this yet, I'll have to take a look at it.
Thanks for the Video! Is the audio from HDMI output just a bypass or after effect (with EQ, compressor that has applied)? Thank you
I'm a moron, can someone please explain this to me?
I have 2 microphones, say they're Shure SM7B's, I connect them to my Scarlett 2i2 audio interface, I then connect that interface to my computer via a USB-C to USB-A cord. usually, I record directly into audacity.
I'm wanting to know how I can connect this set up to the ATEM mini for live streaming so that I can combine my high-quality audio to my high-quality video while LIVE!
THANKS IN ADVANCE!
To get audio through your Atem Mini, take the analog Left/Right output on the back of the 2i2 and connect it to one of the Mini's inputs using a cable like this (amzn.to/3sxayIv) You'll want to turn the "direct monitoring" switch on the front on. Also set the Mini's audio inputs to line. In this configuration the 2i2 is acting like a 2 channel preamp and mixer. If you are using software on a computer (like OBS) to live stream, then you could also just keep your current 2i2 setup and add an audio device to your scene in OBS and bring the audio in from the 2i2. Video from Atem, and audio from 2i2.
Wait, just the cable? But typical mixer gives balanced mono while ATEM will want unbalanced stereo. I've read that without the conversion (with something like DI box) the resulting audio will not be good. I think I've heard the term "off phase" basically, one of the channels will have reversed phase...
Yes, you need to make the conversion with your cable.
@@BallastMedia I did a research, cable is not enough, you need a DI box.
@@JuriyBura You can directly cable a balanced line to an unbalanced connection, if the wiring is done correctly, but it negates the advantage of the balanced line, basically you're just running an unbalanced cable. (Using a direct box would keep the "balanced" portion of the line in tact, yes.) Also, you can't connect a mono balanced line to a stereo unbalanced input - this is usually where most people go wrong and have issues.
This is the best video explaining audio connectivity for live streaming !!!!
The new Fiber Optic HDMI cables can run 300 feet without a booster. Just remember that they are directional.
Good stuff. I needed a straight forward video about setting the audio levels, compression and limiter on the mini so when my mate and his companion are live on facebook, and he treaks the gain for a little more omph, I don't have to constantly tweak the audio and can concentrate on the video and monitor the stream.
lol, talking about great sound -> showing a fully red audiobar at second 08.
;-)
Great tutorial...
We use a small Mackie creator mixer that has 4 separate headphones output jacks...
Wondering about patching from my headphone output to the mic input of the atem switcher...
This way it leaves my full size mixer line level outputs jacks available for the powered monitors and other works...
What do you think?
Better not to use headphone output to drive line inputs. There is an impedance mismatch there that can cause distortion earlier then you'd normally have.
If your mixer doesn't have enough line level outputs, just use a distributor, something like this can work: amzn.to/42Y6Smt
Thank you. I've been looking for this informatuion for ages.
So have i...it was an INSTANT gratification
Steven, I messaged your page on Facebook for an answer, do you take questions there?
Hi
Sound and eqlazar setting video
How to livestream in 4k? Any other equipment?
Thank you. Just starting with the atem at my church and audio has been an issue. This should help a ton.
Amazing tutorial. Thx!
Great video!!
Is OBS necessary or can we just use the ATEM software?
Any suggestions on how to get a balanced XLR Aux out on my sound board to the unbalanced 1/8" stereo input on my ATEM mini pro switcher? Would changing the audio input to "LINE" fix the sound issues we are having with that? My understanding that because of phasing it is canceling some of my signal out and causing it to have terrible sound going direct from my board to the ATEM Mini. We've tried using a variety of direct box options, but not a lot of options going from balanced to unbalanced (although plenty of options the other direction) and I'm having issues with every one I try. HELP!
You need a cable like this that is wired to convert balanced to unbalanced: amzn.to/32WaE2l You really don't need a box in between. Yes, make sure you have set the audio settings in the Mini to set the Mic input to LINE level.
Why can’t I run my mics into the audio interface and connect the audio interface to the ATEM Mini Pro?
Do you mean an audio mixer? Yes you can do that, just set the Mini to line level. Usually an audio interface has usb as it's output, and that won't work to connect to the mini.
Thank you for a great walkthrough and tutorial!
Ballast Media is one the place we can see our problem fixed.
Dude.....I have been trying for weeks to run my Korg Kross 2 Keyboard workstation and usb microphone through my Atem Mini Pro and could never get my sound mixed properly.In just less than 10 minutes I have 3 variations of presets for varying scenarios.....Thanks man,you are a life saver!
Excellent video @Ballast Media. Can't help but ask if any future video audio plans that may cover other software or tools, especially X-Split, but others as well such as Wirecast, Vmix, etc.?
So I have a question. Im sending two 1/4" TRS cables from an audio interface mix to an Atem mini, would that require using both the mic inputs on the Atem Mini to have a true stereo mix for live stream?
Dual TRS connector means those are balanced. The input of the ATEM is unbalanced stereo, so you need a dual TS to stereo 1/8" cable like this: amzn.to/30fXUoH
Loving this ATEM mini series! I will buy this hardware because of this playlist! Thank you!
HI, is not possible to send digital audio to any atem mini i think, that would take me to more expensive switchers... I wanted to get in thru AES or AES67
No, the Atem only takes analog audio in, or audio from the cameras.
Hi Ballast . i intent to livestream with one keyboardist and 2 vocalists. My question is if i use a mixer to feed in Mini or mixer + interface to PC, which way is better in term of sound quality. Thanks
Using a dedicated audio interface may sound better, but in reality I doubt you will notice much difference.
Kool. Do i really need a box to convert 1/8" balanced to unbalanced signal to Mini?
The biggest problem I deal with (with the Minis) is noise and hum. Usually it’s alleviated using a stereo DI, yet today I did an install where the noise was still present; the mixer at the install is noisy, so that may be contributing despite successful installs with the Minis in the past. Switching the input to line level, I had no idea it was embedded in the software. Thank you for sharing!
I’m big on low latency so my video/audio syncs up. Any other latency issues as of today? and do you have some recording done from it so I can see examples live? Thanks a lot for the info 💪🏽🙏🏽
Could you make a video explaining how to add headphones in order to listen to the output?
Probably the easiest way to monitor is to use your computer - connect to it's headphone output and in OBS set the audio properties to Monitor and Output.
Just what I was looking for. A video that would take someone like myself, with little technical knowledge, step by step through the process. Love how you split the videos in to parts too.
Quick question, can I get a similar result by using, what I’m told is an easier platform, something like Streamyard. If so, is it something you’d consider making a video on 😉
I have our Mini audio setup as you prescribed here. Spoken voice sounds great but music sounds like the notes are getting cut off and is choppy. Any suggestions?
How is the mix sent to the Mini? Sounds like you need to work on the levels to balance out the difference. Broadcast is a whole different animal when it comes to gain structure, we're used to having widely different levels in the house (50-70db for speaking and 70-100db for music) and that just doesn't translate to video. You need to work on your mix going in to the Mini to balance that out some. Compression can help a lot.
How do you setup with Presonus Studio Live 16?
I'd take an Aux mix output from the Studio Live to the Mic 1 input (switched to Line level) of the Mini.
excellent
Thank you so much Sir.
Thank you sir. I have the traditional Atem Mini and was kinda stuck. After watching this video I'm definitely getting things done. I will share the link to your TH-cam channel so you get 1million subs ❤🎉
When I connect my mixer to my ATEM, it will have noise either with line or microphone. Anyone could help?
What kind of noise? Is it a constant buzzing sound? Most likely that is a ground loop.
Important to note, if you're running 1/4" out to the ATEM. (This doesn't apply if you use XLR outputs.)
The suggested dual 1/4" to 1/8" cable for sending audio from board to ATEM assumes your board is outputting *unbalanced* audio, and so it's appropriate to hook up to it a cable that has only two strips of metal visible on the plug, the Tip and the Sleeve (TS). TS cables send two different signals along two different wires: a ground signal on one, and the audio signal on the other.
But often sound board outputs are *balanced* audio (which is much more resistant to interference than unbalanced audio, hence works over longer distances). And balanced audio requires a balanced cable containing *three* wires, with plugs consisting of three strips of metal: the Tip, a Ring, and Sleeve (TRS). A mono balanced signal breaks down into three signals in a balanced cable: a ground signal, then two other signals that encode the audio signal but in a manner overall resistant to interference. (XLR outputs will similarly transmit a mono balanced signal through their plug's three pins.)
If you try using the recommended unbalanced dual 1/4" to 1/8" cable when your board outputs balanced audio, you're gonna have a bad time. If the balanced audio is "impedance balanced" (Tip is signal, Ring and Sleeve are ground), I believe it'll still work (but you're vulnerable to interference). But if it's "symmetrically" or perhaps "electronically" balanced (Tip is half signal, Ring is *inverted* half signal, Sleeve is ground -- so the actual signal is Tip minus Ring), audio will either be very degraded or just won't work, I'm not entirely sure which.
If your board's outputs are balanced, you need to include a balanced-unbalanced conversion in the pipeline. Running two balanced 1/4" TRS to XLR cables from board to an ART CLEANBoxPro Dual-Channel Level Converter, then running a (ideally short) TRS-TRS microphone cable from that into the ATEM, should do the trick (I believe with the input set to Mic in ATEM settings). This will give you a stereo audio input, left/right corresponding to the two board outputs. If you only have one board output, you can just run it to the ART box, then in ATEM settings split the mic input and pan the active half to center and turn the unused half to zero.
Hi Stephen - Tom M. at Cherokee Park United Church in St. Paul (again).Thanks for all your information - I'll ask this Q as briefly as I can: If we're not going with the ATEM mini yet, but using a camcorder with the amzn.to/2XiOzHs you mentioned to me before, would we get in big trouble if we continued to use the USB mic we are using now (Snowball Blue facing a PA speaker) plugging its USB into the laptop along with the USB of the video adapter? Sync problems?
The reason we wouldn't go with a direct from our PA to the camera input is that we're in the front of the church now (closed church due to pandemic). Too far to run the cable. Later we could if we move the camera to the back - but by then we should really consider the ATEM mini, even with one camera. Right now, I'd just like to get off of the webcam (Logitech) that we're using because the picture is such low quality.
I guess I have to ask: can the software for the video interface *and* OSB be expected to run on my i5 8GB SSD Lenovo laptop? We are definitely seat-of-the pants now, but I've heard that the Presbytery will have some grant money for approved hardware for little churches to stay on line. I'd want to use any money wisely. Thanks again, you are really providing a service at a critical time! -
Hallo, I have a microsoft surface pro 3 notebook (Windows) connected with hdmi to the MINI. Unfortunately there ist no SOUND transported. Do you have an idea, how I can hear the SOUND. Thanks a lot.
Would you still recommend the canon xf15 and the xf200 for multi cam shoot? You recommended these cameras in 2016 and I was wondering would that be the same recommendations given this is 2020. Thanks in advance
Nice video. I noticed the dynamics on our ATEM is VERY noisy! (high noise floor). Try engaging the compressor, expander or limiter with no audio passing into the ATEM. Now watch the audio meters - you will notice a lot of noise coming into them. I had to disable some of the dynamics as it noise was very audible during spoken word.
We record via 2x 8 channel interfaces run Aggregate on a Mac Pro into Presonus Studio One 4 Pro. Is there a way to use the ATEM Mini for a livestream sound? I'm really at a loss on how to record and get a mix for a livestream from the DAW... Any ideas?
Great infos ! Do you how to avoid atem mini to make an audio input appear only on the left channel ? I tried to do that by splitting the channels into mono but it mutes the audio completely even though it appears on the decibel meter.
Hi I really like your easy to understand tutorials. I used these settings yesterday at our church stream and everything went pretty well, except I now have a couple of questions I hope you will answer.
First when I changed the mic 1 to line it took almost all my gain away. I had to go back and use a third setting our Atem Extreme has that is called mic or output in?? I also noticed that there is a screen that shows makeup gain. Is this what I should have used to make up the lost gain by using line setting?
Second question I am wanting to use the lower thirds from Propresenter 7 but our church has an older computer that is using VGA to 3 projectors. Atem requires me to connect using HDMI which I don't have. Is there another way to connect this computer to the Atem? Thanks for all your work it is really helping us church volunteers!
I'm a bit confused. Couldn't you just delay the audio in Advanced Audio Properties in OBS?
Hi Steven!
I own a Behringer 1202FX mixer and an Behringer Euphoria 404...Is there a way to connect this to the ATEM Mini?
Thanks in advance!
Yes, you can most likely figure out how to connect just about any mixer to the Mini. Kind of depends if you want an Aux mix for your video or the main mix, but you'll need a Dual 1/4" to Stereo 1/8" cable (some are linked above in the description of this video) and set the Mini to Line-Level.
Ballast Media thanks for taking the time to reply, answer my question and get me out of doubts! Bless!
Great video! The most frustrating for livestreaming is the audio. We have a Y cable coming off the mixer, one side is connected to the mini, the other side is to plug in headphones to hear the mix prior to going through the mini. The mix sounds fine in the headphones but what gets livestreamed to FB is really quiet (even though the meters in the mini are hitting the yellow area) plus its really flat and "tinny* sounding. I'm realizing now the mini has an EQ lol. Is there anyway to turn off that eq?
How do i get audio from My Pocket 6K ? on OBS. It doesnt seem to pick up the audio from the HDMI 1 but it does pick up the audio on the ATEM CONtrol software
Have you turned that HDMI input's audio ON in the audio mixer of the ATEM? All camera inputs are off in the audio mixer by default.
@Ballast Media
Yes i have turned every audio connected to the Atem. And also on OBS i put the audio of the capture card as a microphone and still hear nothing
Hi there, not sure if this has been asked before, but is it possible to monitor the audio output with Atem Mini and OBS through headphones? Also, I'm setting up a livestream, with audio coming from a sound system which is for our mics etc. previously we've used a 1/4" cable into the laptop through an audio interface. However, I want to connect the sound system direct into the atem mini with a 3.5mm adaptor. Can you foresee any issues with this? Thanks
In OBS you can set the audio to be "Monitor and Output" in the "Advanced Audio Properties" (right click on the audio mixer). Then you will be able to listen through your computer's audio, eg connect headphones to the computer. You should be able to connect a mixer directly to the Mini without any issues, just be sure to change the Mini's audio inputs to "Line"
@@BallastMedia That's great. Thankyou.
A cheap Behringer mixer with unbalanced output works and it is better to use the HDMI output cause it has the better quality so you need a capturecard too. And it works with the old Adobe Flash Media Live Encoder for te coding to the internet. And if you are a CamTwist user it works with that too so this is a very cool product.
Thank you. I love us. :)
I need some help!! I am running an Allen and heath sq5 for our front of house at my church, usb 2.0 out of the console into a MacBook Pro running Logic Pro x. The Logic template is from bethel and uses a lot of waves plug ins. Then I am going 3.5mm out of the MacBook Pro into the mic 1 line of the atem mini. When we live stream the audio is behind the video.... I have no clue how to fix this as every video I see only deals with delaying the audio to match up with video. In my case I would need to delay the video to match it up. Any thoughts on how to fix this??
Are you going in to OBS? You can delay the video in OBS with a filter. But ultimately it would be good to get your audio IO speed a little faster. What are your buffers set to in Logic? That might be contributing to the amount of latency, just be careful because if you set the buffers too small Logic will start to glitch.
Ballast Media Ballast Media thanks for the tip with OBS! I’ll probably need to watch some videos on connecting the atem to that but I’ll definitely look at the video delay filter function. Also, my I/O buffer size is set to 128 and the process buffer range set to medium.
Awesome man! I'm hoping to pick up one of these soon to improve my online drum lessons. I can have my drum mix go to input 1 and my talkback on input 2 to switch between talking and playing. As well as free up all my usb ports! 😂
Great info here but audio speaker out works clearly on iphones but not so well on android phones what could be the issue please
Listening on a phone speaker is summed mono, so that would suggest you might have your left and right channel out of phase.
Thanks Stephen! I will try it.
Good video. I wanna buy that model for home streams. At work I have ATEM Television Studio HD, but it have redundant functionality for me and my musical streams.
thanks for the helpful video! i will be streaming live music via 4 different cameras in four different areas of the studio. all the music will be fed into a single mixer. i was wondering: 1) since the cameras will only be for visual purposes, do i need to go the iso route? 2) any advantage, from a STRICTLY audio standpoint, to go with extreme rather than pro? thanks again!
Audio is the same on all Mini models as far as I'm aware.
Is there any way to synchronize the delay that may exist in the video from different cameras in the atem mini or atem software? as they do with the audio
No unfortunately you can't delay individual cameras in the ATEM.
Hi, thanks for the very helpful video. I currently have 4 mics going into a firewire interface, and within Ableton Live, I apply EQ and compression and other bits such as limiting and deessers. Would I be able to plug the headphone output of my interface straight into the mic input of the Atem? I'm assuming there will be an audio delay as it's running through my DAW first, is there any delay compensation you're aware of within the Atem software? Many Thanks
Can you see that audio interface in OBS? I'd just use that and have obs combine your audio and video, rather then do another AD/DA conversion.
I usually do the audio setup on the mixer and then send it post eq to my live stream. is it better to do the audio setup from the atem then?
If you have the capability to do it on the mixer, just do it there. Sometimes depending on the application the mixer needs a different EQ for the room, or doesn't have the ability to provide the stream with the EQ it needs.
wooooow you answered all my questions......Thank you Sir
Thank you for this video ! We have some sound issues with a sport broadcast for one of our clients, it will really help us
Great . How do You remove the controller stuff on the screen when using iPhone as camera? I only want to show the picture
Thank you, my congregation is going to benefit a lot from this, to be able to spread the word, let the glory be to God.
Thank you for the video. Is it possible to get a Dante Audio input in Atem Mini Pro?
thank you sir you r the best ...ahmed from tunisia
Hi sir. My self Mahesh from India. i have watched all ur videos about ATEM MINI. but I did not understand whether we can receive the audio from audio mixer to Live via ATEM MINI. 2. Can we receive the video through HDMI if camera has the HDMI port without any video capture card. Can we use the ATEM MINI as a video capture card. This is for our church service and we are actually planning to purchase the ATEM MINI. hence please help me in understanding.
I will be waiting for your response sir. Thank you in advance.
1. Yes, you connect your audio mixer to the audio inputs of the Mini.
2. Yes, the video from the camera goes in to the Mini, and the Mini send the video to your computer through its USB port. You don't need any other capture cards.
@@BallastMedia Wow. Thank you for your help sir. Ur videos are very helpful for the people. Thanks a ton once again ☺️. M happy 😊.
Great video ! But I am not an audio maestro :) So excuse me if I am asking meaningless questions. I have two wireless lavalier mics (1 Sennheisser ew100G3 and 1 Sony UTX-B03) and their original cables (1 xlr and 1 3.5mm outputs), so my question is do I have to choose "line" instead of "microphone" at the ATEM Mini setup software ? Thanks a lot
It depends what the output of the device is. If your signal is really low and you are on Line, switch to Mic. If you are on Mic and it's distorting easily, switch to Line.
THANKS
Line input were unbalance tho.
So i assume we need unbalanced out from mixer.
Will this setup give the full stereo experience and not mono?
The input to the Atem Min is stereo, yes. but you need to send it a stereo signal using the correct wiring - but yes, you should get stereo.
Excellent video, my man. These step-by-step methodical approaches really help me get things together.
Thanks for your great videos! Question: Will this device, and following the instructions you mentioned in this video help with following LKFS (or LUFS) monitoring requirements? I'm mixing through an A&H board into a complete audio 6 and into OBS and out to CASTR (via your CASTR tutorial, thanks). The worship music (keys, ac. guit. 3 vocals) sounded great on youtube but on FB it sounds fine for about 7 seconds then you can hear their compression kick in and the instruments sound like toys. My research is saying that for facebook I should be at around -16 LKFS. Will this device and instructions help with this problem? Or do you have another video that addresses this?
You would still need to measure and adjust to hit those targets accurately, but yet, using a compressor is the way to hit the target and average you want.
thanks for the video
I’m getting a a hum noise. Maybe I’m using the wrong cord. I brought a 3.5 to a single balanced cord. Is this the wrong cord to use for this application??
Most likely a ground loop. What is your audio path? Where is it coming from in to the Mini.
Do you have a email?
I’m running out of our sound board. I ordered those cables you recommended plus a 3.5 to rca. After I watched your EQ video I think I have solved the issue. Can you do a video on the volume adjustments in the mini pro? Thanks for responding
Not sure if this is the place to ask, but this tutorial is about audio. I am relatively new to the ATEM. I am using the 'Fade To Black' feature to fade in and out on live streams. The audio does not fade with the video. Is this a simple setting I am missing, or do I have to create a macro just to get the audio to fade in and out? I can't find this issue being addressed anywhere. If I follow the tutorial - the part about running the audio into the ATEM and bypassing the camera - will the audio then be controlled with the video when utilizing the FTB button?
Unfortunately, yes, I think you need to use a macro to accomplish that.
We were going to get an audio interface (Scarlett 2i2) to get a clean output into OBS from our mixer but would this be needed if were were to go with the ATEM (mixer to stem to computer & mix with ATEM)?
Not needed, no.
Where do you plug the connection from mic 1 to digital mixer?
What mixer do you have? What mix output on that mixer are you wanting to use?
@@BallastMedia Xr18 but I also running PA in person.
When i connected the atem mini pro to obs, im not getting the audio input into obs. Kindly help
Sometimes in obs you have to open the properties for the atem, and scroll down to the "use another audio device" check box, check it and in the drop down that appears, select the atem. Weird, but works.
@@BallastMediaThank you so much... It worked.
hats off to you sir have been dealing with bad audio forever
What audio mixer do you recommend???
I would need to know lots of information about your needs before I could recommend something. How many channels do you normally use, how many aux mixes (monitors, effects) do you need, what other routing do you need for monitors, broadcast, etc.
What’s the difference between mini vs Hd for £800
The Atem TVS HD adds additional SDI inputs, an Aux output and it has a multiview output display.