Hi, this is a very common problem. I have encountered this fault many times. You need to find the cause of the laser cleaning motor blockage, so follow these steps: 1 Executing the Laser Scanner Cleaning The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Execute Laser Scanner Cleaning. Adjustment/ Maintenance Menu 2 Cleaning the LSU cleaning drive gear and the cleaning pad The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Clean the LSU cleaning drive gear and the cleaning pad. 3 LSU replacement The LSU cleaning drive gear, cleaning wire or the cleaning pad are deformed, or they are faulty. Hope you can get the copier fixed. Looking forward to hearing from you if it is successful. Greetings.
Really idont know but: Communication error between the engine ASIC During the readback data checked after data transmission, the checksum error or the video signal is not inverted. (failed 10 consecutive times)
Hi, this is a very common problem. I have encountered this fault many times. You need to find the cause of the laser cleaning motor blockage, so follow these steps: 1 Executing the Laser Scanner Cleaning The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Execute Laser Scanner Cleaning. Adjustment/ Maintenance Menu 2 Cleaning the LSU cleaning drive gear and the cleaning pad The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Clean the LSU cleaning drive gear and the cleaning pad. 3 LSU replacement The LSU cleaning drive gear, cleaning wire or the cleaning pad are deformed, or they are faulty. Hope you can get the copier fixed. Looking forward to hearing from you if it is successful. Greetings.
The communication between the IH PWB and the engine PWB does not succeed at the initial communication. (The retry is executed 10 times in 150ms intervals.)2. The communication between the IH PWB and the engine PWB does not succeed for 500ms after the initial communication success.
There can be as many as three options: Drum unit, Drum motor or Engine PWB. Remedy: Drum unit 1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace. 2. Confirm that the drum or the drum screw can rotate. 3. If it won’t rotate, replace the drum unit. Drum motor 1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5) 2. If the wiring is disconnected, shorted or grounded, replace the wiring. 3. Replace the drum motor. Engine PWB 1. Check the engine software and upgrade to the latest, if necessary. 2. Replace the engine PWB.
This is a problem with the fuser, but first make sure the fuser is not damaged or worn. Check the condition of the heating rollers and make sure that the rollers rotate freely. If there is a problem, replace the shafts and bearings or the Fuser Unit. Thank you and invite you to subscribe to my channel. For me it's very important.
Reinstalling the developer unit The developer unit is not properly installed. Reinstall developer unit C so that the connector firmly connects. Developer Unit Replacement
This is a serious matter. Read it: 1 Resetting the main power The power startup delays. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the wire The wire is not properly connected or is faulty. Reinsert the following wire connectors, and replace the wire when it has no continuity.• IH PWB - Engine PWB Electrical Diagram of PWBs 3 Checking the wire The wire is not properly connected or is faulty. Reinsert the following wire connectors, and replace the wire when it has no continuity.• LVU - IH PWB Electrical Diagram of PWBs 4 Checking the power supply voltage The abnormal electric noise is mixed in the power supply voltage. Plug the power cord into another wall outlet. 5 Checking the LVU The fuse on the LVU is broken. Check the continuity of the fuse (F002) on the LVU. Then, replace the LVU if there is no continuity. LVU Replacement 6 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. IH PWB Replacement 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Upgrade 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Engine PWB Replacement
Hi, just DP lift motor going down error. Remedy: Loose connection of the DP lift motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Malfunction of the DP lift motor. Replace the DP lift motor and check for correct operation. Malfunction of the DP lift lower limit switch. Replace the DP lift lower limit switch and check for correct operation. Loose connection of the DP lift lower limit switch connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Defective DP main PWB. Replace the DP main PWB and check for correct operation.
Broken the gear or defective toner motor M/C/Y/K. Broken the gear. Check visually and replace the gear if necessary. Defective toner motor M/C/Y/K. Run maintenance item U135 and check if the toner motor operates. If not, replace the toner motor.
Maybe you have a damaged paper lift motor or there is paper on it? Remove the paper and reset the cassette. If that doesn't help, then: Poor contact in the connector terminals. Defective engine PWB.
This is a developer problem. You have to take out the developer unit and put it back in correctly. And if that doesn't help, install a new one. TH-cam SUPPORT: th-cam.com/channels/OHtXTtGHj33pUm8Gf2FH3A.htmljoin PATREON: www.patreon.com/CopyExpertMovieStudio PATRONITE: www.patronite.pl/1796
In my opinion, there is no code c2960 in kyocera copiers. Do you mean such a sensor? : copy-expert.com/pl/searchquery/termistor/1/phot/5?url=termistor This is a bimetal thermistor that fuses itself when heated, don't touch it. Check again your error code C -.... because you probably made a mistake.
Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB and check for correct operation. Defective paper feeder main PWB. Replace the paper feeder main PWB and check for correct operation.
For the specified value of the initial toner stored in the EEPROM of the developer unit, the output value of the T/C sensor is out of the range between +100 (undetection toner) and -1000 (Coming off of the sensor connector). And that status was detected 3 times continuously.
Peace be upon you. I wanted to learn how to maintain a Kyocera photocopy machine for a fee in Arabic
@KhaledAbdElmonem-f8v What Kyocera model do you have?
C4600 occurred when trying to perform laser cleaning on a screen, so the code appeared even after putting printer off/on it remained
Hi, this is a very common problem. I have encountered this fault many times. You need to find the cause of the laser cleaning motor blockage, so follow these steps:
1 Executing the Laser Scanner Cleaning The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Execute Laser Scanner Cleaning. Adjustment/ Maintenance Menu
2 Cleaning the LSU cleaning drive gear and the cleaning pad The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Clean the LSU cleaning drive gear and the cleaning pad.
3 LSU replacement The LSU cleaning drive gear, cleaning wire or the cleaning pad are deformed, or they are faulty.
Hope you can get the copier fixed. Looking forward to hearing from you if it is successful.
Greetings.
hi, i have c0360 error on Triumph Adler P-C3060. I try reset error but in maintenence menu there isn't 163 option, only 167 that is fuser reset.
Really idont know but: Communication error between the engine ASIC During the readback data checked after data transmission, the checksum error or the video signal is not inverted. (failed 10 consecutive times)
Can you help me solve C4600 in kyocera 2551ci?
Hi, this is a very common problem. I have encountered this fault many times. You need to find the cause of the laser cleaning motor blockage, so follow these steps:
1 Executing the Laser Scanner Cleaning The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Execute Laser Scanner Cleaning. Adjustment/ Maintenance Menu
2 Cleaning the LSU cleaning drive gear and the cleaning pad The LSU cleaning drive gear and the cleaning pad have the load and so they are not shifted smoothly. Clean the LSU cleaning drive gear and the cleaning pad.
3 LSU replacement The LSU cleaning drive gear, cleaning wire or the cleaning pad are deformed, or they are faulty.
Hope you can get the copier fixed. Looking forward to hearing from you if it is successful.
Greetings.
Hello I have code error F010 on utax 4035, what should I do?
This is a very serious error related to the controller board or disk. Please let me know if you managed to repair the copier.
hi, kyocera 50021 erorr cannot use 2-sided original due to failure, can you help me?
I don't know the kyocera 50021 model
@@MrRicoh sorry , kyocera taskalfa 5002 i
I have kyocera fs_c5015n error code call service 7600
Does it have non-genuine toners? Maybe a used developer? There are several options to check.
تعطى كود c6950ماحل هذة المشكلة بالتحديد من بوردة البور
The communication between the IH PWB and the engine PWB does not succeed at the initial communication. (The retry is executed 10 times in 150ms intervals.)2. The communication between the IH PWB and the engine PWB does not succeed for 500ms after the initial communication success.
Note the following error code. Turn the main power switch off and unplug the power cord.
Explain it please
I think you need to turn on the subtitles and watch it again. I guess everything will become understandable. If not, write to me.
Good day
I have problem code error C2550 kyocera 6501i what can I do
Open the right door in the photocopier and disassemble the transfer unit. Disassemble the transfer belt and clean the inside of the dental unit.
Can you help me sir, How to solve c2211? Thanks
There can be as many as three options: Drum unit, Drum motor or Engine PWB.
Remedy:
Drum unit
1. Check the drive gear can rotate or they are not unusually loaded and, if necessary, replace.
2. Confirm that the drum or the drum screw can rotate. 3. If it won’t rotate, replace the drum unit.
Drum motor
1. Confirm that the wiring connector is firmly connected and, if necessary, connect the connector all the way in. drum motor and Feed PWB 1 (YC9) Feed PWB 1 (YC2) and Engine PWB (YC5)
2. If the wiring is disconnected, shorted or grounded, replace the wiring.
3. Replace the drum motor.
Engine PWB
1. Check the engine software and upgrade to the latest, if necessary.
2. Replace the engine PWB.
how to sovle c2300 in kyocera 4501i
This is a problem with the fuser, but first make sure the fuser is not damaged or worn. Check the condition of the heating rollers and make sure that the rollers rotate freely. If there is a problem, replace the shafts and bearings or the Fuser Unit.
Thank you and invite you to subscribe to my channel. For me it's very important.
Hi can you help ? how to solve kyocera 2552ci error code c7102
Reinstalling the developer unit The developer unit is not properly installed. Reinstall developer unit C so that the connector firmly connects. Developer Unit Replacement
opa me ajuuuuuudddaaaaaaaa
to com esse codigo de erro c6950 nao consigo tirar me ajudaaaaaa como eu tiro
This is a serious matter. Read it:
1 Resetting the main power The power startup delays. Turn the power switch and the main power switch off . After 5s passes, turn the main power switch and the power switch on. 2 Checking the wire The wire is not properly connected or is faulty. Reinsert the following wire connectors, and replace the wire when it has no continuity.• IH PWB - Engine PWB Electrical Diagram of PWBs 3 Checking the wire The wire is not properly connected or is faulty. Reinsert the following wire connectors, and replace the wire when it has no continuity.• LVU - IH PWB Electrical Diagram of PWBs 4 Checking the power supply voltage The abnormal electric noise is mixed in the power supply voltage. Plug the power cord into another wall outlet. 5 Checking the LVU The fuse on the LVU is broken. Check the continuity of the fuse (F002) on the LVU. Then, replace the LVU if there is no continuity. LVU Replacement 6 Replacing the IH PWB The IH PWB is faulty. Replace the IH PWB. IH PWB Replacement 7 Firmware upgrade The firmware is not the latest version. Upgrade the engine firmware to the latest version Firmware Upgrade 8 Replacing the engine PWB The engine PWB is faulty. Replace the engine PWB. Engine PWB Replacement
how to solve C 9050 ERROR in kyocera 620 taskalfa?
thanks
Hi, just DP lift motor going down error.
Remedy: Loose connection of the DP lift motor connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Malfunction of the DP lift motor. Replace the DP lift motor and check for correct operation.
Malfunction of the DP lift lower limit switch. Replace the DP lift lower limit switch and check for correct operation.
Loose connection of the DP lift lower limit switch connector. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.
Defective DP main PWB. Replace the DP main PWB and check for correct operation.
@@MrRicoh DP means? Sorry i didn't understand?
www.google.com/search?q=kyocera+dp+lift+motor&client=firefox-b-d&sxsrf=ALeKk03AAR7MY_dhSE7heb70SYKyv_tqxQ:1622742465028&tbm=isch&source=iu&ictx=1&fir=_z_DUv4IsUhyLM%252ChouvDgbMBN4qlM%252C_&vet=1&usg=AI4_-kS1wXgtDedG86zd1avDh1bbf6Bpxw&sa=X&ved=2ahUKEwiU_8HhgvzwAhVOrIsKHfsrCNwQ9QF6BAgNEAE#imgrc=_z_DUv4IsUhyLM
Can the machine's paper usage counter be changed?
Yes, you can do it, but only once. The copier will remember this reset forever and cannot be done later.
@@MrRicoh Plz give me code
hello sir kyocera 250 ci error c7000 plz can explain where is problem and what to do
Broken the gear or defective toner motor M/C/Y/K. Broken the gear. Check visually and replace the gear if necessary.
Defective toner motor M/C/Y/K. Run maintenance item U135 and check if the toner motor operates. If not, replace the toner motor.
@@MrRicoh sir whats in gears is near drum if any image can help me
thx sir
hi sir
HI @ABCJAYAPRAKASH JP
How resolve error code c7911
This could be a problem with the developer unit. Have you repaired this module?
c0500 ?
Maybe you have a damaged paper lift motor or there is paper on it? Remove the paper and reset the cassette. If that doesn't help, then: Poor contact in the connector terminals. Defective engine PWB.
can you help me error c4201
Im my opinion: Reinstall or replace the LSU while paying attention to the static electricity.
@@MrRicoh what is the LSU
It is Laser Unit
c6610 Error Solve Problam Please
you have to look this: printcopy.info/?l=en&mod=erc&brand=Kyocera&model=TASKalfa%202552ci&code=C6610
266ci kyocera error 2740
This is a developer problem. You have to take out the developer unit and put it back in correctly. And if that doesn't help, install a new one.
TH-cam SUPPORT: th-cam.com/channels/OHtXTtGHj33pUm8Gf2FH3A.htmljoin
PATREON: www.patreon.com/CopyExpertMovieStudio
PATRONITE: www.patronite.pl/1796
Plz help in 3500i error F000
You have to replace HDD and install new firmware from USB
@@MrRicoh sir plz provide firmware. I have many try on net but still disappointed. Plz
Sir no idea for firmware 3500i
c2960 pls
do you have this error code in the kyocera copier?
@@MrRicoh i got that message on kyocera taskalfa 2552ci bro
@@MrRicoh I saw a broken wire in the heater sensor. is it safe to solder a broken wire?
In my opinion, there is no code c2960 in kyocera copiers. Do you mean such a sensor? : copy-expert.com/pl/searchquery/termistor/1/phot/5?url=termistor
This is a bimetal thermistor that fuses itself when heated, don't touch it.
Check again your error code C -.... because you probably made a mistake.
@@MrRicoh Could I send You a photo by email?
Hope this will clear error 3300
That should help you. I invite you to subscribe to my channel.
Pls how do I clear error code C0650 on taskalfa 3051 machine
c6250
You have a problem with the thermistor.
You can get more support in our Facebook group facebook.com/groups/270664767463482
C1800 KM5050 please
Poor contact in the connector terminals. Check the connection of connector on the engine PWB and the connector on the paper feeder main PWB, and the continuity across the connector terminals. Repair or replace if necessary. Defective engine PWB. Replace the engine PWB and check for correct operation. Defective paper feeder main PWB. Replace the paper feeder main PWB and check for correct operation.
@@MrRicoh F684 error code how do you solve
C2550 error code in kyocera task alfa 3500
Are you a subscriber to my YT channel?
Yes
F000
This is a very serious mistake, I don't know the solution
c7101?
For the specified value of the initial toner stored in the EEPROM of the developer unit, the output value of the T/C sensor is out of the range between +100 (undetection toner) and -1000 (Coming off of the sensor connector). And that status was detected 3 times continuously.