Thanks for this! I bent and broke the bolt connecting my clutch pedal to the clutch. Then I ended up stuck in 5th, so I just replaced the entire clutch. This video helped so much
Replacement Clutch came as an assembly. Just put it in as is. Final assembly leaves the clutch spring lever (where the cable mechanism goes into the case) is loose and freely pulls out, leaving no tension at the clutch lever up top.. what did I do wrong?
do you have any curved/bent steel plates? i found 2 in my clutch set and they look identically the same, i dont know if theyre supposed to look like that
Just switched my clutch out on my 2009 rebel…. After I did now my clutch gets stuck and I can’t pull it after riding for like 10 minutes and I have to rev match to downshift without the clutch to the point where I’ll stall out bcuz I can’t pull the clutch… any idea what it could be?
question: today I tried to do the clutch with a mate, on his 88 Rebel 450. I noticed I didn't have the right socket for the clutch nut, so we put it all back together. Now the bike won't neutral itself while in gear (with the handle pulled). What could've gone wrong. I used the same torque specs as on my Vulcan750 clutch basket. and it seemed to fit fine without any force
The round thing with teeth on it the clutch sits in what is it called and should it just it just slide out or do I have to losen some bolts and put in between the gears that needle thing sits in and sit it it in there because mine slides all the way off?
That's the clutch basket, when the nut comes off at 10:25 the entire clutch assembly, hub which I take out in this video, and basket, which you are asking about can slide right off. If you pull the basket off pay attention to the bearing and washers.
I need help :( I tried pressing down on the brake to wrench out the lock nut but it keeps turning :( Any tips? The bike is not on a stand, its on the ground. It’s also in 5th gear. What am I missing? :( Thank you in advance
Sadly I can’t find any help for the newer 500s it’s pretty much the same but I’m stuck after I put the new disks in there’s still play in the pack I’m at a lose
Did you measure the plates and fibers before and compare? I would try that, the new plates and fibers total thickness should be thicker. If it is and it still has play, something isn't sitting in there correctly. Just double check your work. Including the actuation bar.
You sir have a gift for teaching. You are patient and explain things very well. Thank you.
Thanks for the kind words.
Thanks for this! I bent and broke the bolt connecting my clutch pedal to the clutch. Then I ended up stuck in 5th, so I just replaced the entire clutch. This video helped so much
Thanks for the video, I didn't see if you replaced the seal as well.
Replacement Clutch came as an assembly. Just put it in as is. Final assembly leaves the clutch spring lever (where the cable mechanism goes into the case) is loose and freely pulls out, leaving no tension at the clutch lever up top.. what did I do wrong?
do you have any curved/bent steel plates? i found 2 in my clutch set and they look identically the same, i dont know if theyre supposed to look like that
Great Video. Learned something!!
Just switched my clutch out on my 2009 rebel…. After I did now my clutch gets stuck and I can’t pull it after riding for like 10 minutes and I have to rev match to downshift without the clutch to the point where I’ll stall out bcuz I can’t pull the clutch… any idea what it could be?
question: today I tried to do the clutch with a mate, on his 88 Rebel 450. I noticed I didn't have the right socket for the clutch nut, so we put it all back together. Now the bike won't neutral itself while in gear (with the handle pulled). What could've gone wrong. I used the same torque specs as on my Vulcan750 clutch basket. and it seemed to fit fine without any force
Sounds like It's your clutch actuator arm that the cable attached to, or the parts that attach to it, inside of the clutch cover.
The round thing with teeth on it the clutch sits in what is it called and should it just it just slide out or do I have to losen some bolts and put in between the gears that needle thing sits in and sit it it in there because mine slides all the way off?
That's the clutch basket, when the nut comes off at 10:25 the entire clutch assembly, hub which I take out in this video, and basket, which you are asking about can slide right off. If you pull the basket off pay attention to the bearing and washers.
I need help :( I tried pressing down on the brake to wrench out the lock nut but it keeps turning :( Any tips? The bike is not on a stand, its on the ground. It’s also in 5th gear. What am I missing? :( Thank you in advance
You'll need an impact wrench for that if it's that tight.
Sadly I can’t find any help for the newer 500s it’s pretty much the same but I’m stuck after I put the new disks in there’s still play in the pack I’m at a lose
Did you measure the plates and fibers before and compare? I would try that, the new plates and fibers total thickness should be thicker. If it is and it still has play, something isn't sitting in there correctly. Just double check your work. Including the actuation bar.
Much appreciated
Awsome. Thank you!
What is the socket called and wear can it get it so I can change my clutch nobody will help they want money you don't have
I put a link in the description for the clutch and the tool. Thanks for watching.
Good evening,
I have the honda rebel ca125, I have to change the clutch, what diameter of the release nut is it?
thanks
I put a link in the description, when you click on it be sure it's for your bike as well.
did you replace the gasket seal?
No I didn't. I had one ordered but it didn't come in time. The original gasket stayed on the case in one piece and sealed back up fine.
Thanks
Thank you
👍👍🙏