Absolutely the best instructional video 😌 I was able used a large russel honbs kitchen knife to make the vertical cuts in the cowling by levering/rocking the knife straight down, then the horizontal 'cut' going back n forth with extreme bending/folding of the plastic until it snapped off.
Just used your video to fit the pedal and control for cruise control, took me maybe 40mins to do, brilliant truly guide. My only comment was the cable onto the pedal had virtualy no slack, still managed it no problem but everyone be awear. Now to get it enabled...
Taking delivery of the parts tomorrow (pedal and stalk). Watched this video over and over again so hopefully tomorrow’s installation will go off without a hitch. Will report back.
Thanks again for the PM’s on messenger @peugeotCitroen2cv. Following your instructions and got cruise and speed limiter working spot on. My 2012 Berlingo Multispace 1.6 hdi 8v with EDC17 engine ECU and 9HP wouldn’t work on any other version of Diagbox other than 7.02. If you get ‘invalid key’ and you drive a 2012 downgrade Diagbox to 7.02. 7.01 - did not work 7.02 - WORKED 7.57 - did not work 7.58 - did not work 7.62 - did not work 7.66 - did not work No version between 7.66-7.83 worked 7.82 - did not work 7.83 - did not work. 7.02 was the only way to go in case you get stuck. Thanks again for the info and the video. Now tempted to try your other videos :) Next tasks for me are: - front top strut mounts - fuel leak from near fuel rail - dpf - blower fan motor That EML I had in the video I sent you was to do with the DPF blocking throwing up other random codes. If you kick it too hard it does that for me occasionally. I need my dpf erased 🤣 Need my blower fan motor replaced. Relay is fine. No blow on any settings. Still get a residue amount of heat or cold depending on the setting but still not blow. Know any easy ways of getting to the blower motor? I have a vague idea of it being under the steering wheel and above the pedals but by Christ is it tight.
I took my 2013 Partner Teepee to a Peugeot main dealer last year, to get cruise retrofitted. They were confident they could do it, checked, installed & programmed everything, but then found on the roadtest that the chosen speed wasn't retained - it flashed back to 10mph or something. After 2 days investigation they admitted defeat, and refunded me what I'd paid for the work. They did mention that there was a fault code related to the resistance of the accelerator pedal (rheostat) which they thought could be relevant - quoted £400 for replacement! As the cc switch is still fitted (Thanks Peugeot!), it would be great to get it working. I did buy a second -hand accelerator pedal on Ebay, but never got round to fitting it. Is swapping the pedal out worth a try - or is the problem more likely to be with the programming?
An excellent guided video! Hoping to tackle this next weekend. I wonder if you may be able to help. What's the software/tool you used at the beginning to diagnose whether your brake and clutch pedals had the appropriate switches?
As we say, dead on man! Now I want to ask you a question, I have a 2014 Citroen Dispatch and I would like to change the twin seat to a single do you know if I can and if so which donor vehicles will be suitable.
Haha they say that here also. Where abouts are you from? The dispatch, not entirely sure, was the E7 taxi version equipped with twin front seats. I think there is a dispatch/boxer (is that the peugeot equivilant?) facebook group ask on there they should be able to give you ideas of what seats to use.
Hello again, I have been trying to get my cruise control working on the Citroen Dispatch 2014 the limiter works and when the diagnostics are connected cruise works intermittently. The guy who done the testing has checked everything on the computer but it still wont work, do you know what else I should try.
@@realcon5086 Mine is on an old XP laptop Tbh i dont actually know the exact version its on, i bought it from ebay about 5 years ago initially i updated to the newest version on the CD but ended up having to going back a few versions I dont use it as much anymore as i have a tablet that does all cars. Only the odd PSA car now, a few weeks ago it was an early xantia abs fault
@@peugeotCitroen2CV thx mate for reply, i installed thw software but doesnt work, it says i need xp or windows 7, gonna try today the virtual windows xp.
Hello thank you for the post. I have done the cruise control part(limiter not required) of the install on my 2008 xtr berlingo, and my mechanic has enabled cruise on the bsi and the ecu, following appropriate steps. I am getting a message on the centre console saying 'cruise control impossible' when trying to activate the cruise control. Is this something you have come across or know how to resolve? Many Thanks Matt
Hi there I came across a mates berlingo that would not let me change the setting on the ECU, it turned out the version of diagbox i was using was too new and i had to install the older version. Are you seeing the cruise control symbols in the LCD screen within the instrument cluster?
Hi thank you for your reply. I managed to get the cruise control working, as you said it was the version of diagbox that was the issue. I do now have another issue though. I purchased the accelerator pedal for the speed limiter, however the new one has 6 electrical pins, whereas the original only has five, with the plug also accommodating five pins. My cable doesn't have the one with the orange clip. Is there a different pedal available with 5 pins or maybe a 5 pin to 6 pin adapter? Many Thanks Matt
@@matthewilett6174 Hi there matt There may be different accelerator pedals for different years, do you see the build code sticker on your berlingo? Google Citroen RPO number to see examples of what i am asking, let me know what your RPO number is and i will see what i can find in terms of part numbers. The 5 and 6 pin pedals will not be cross compatible you will need a different pedal to work with your ecu.
Hey, mate! I've got a 2006 Citroen C2 VTR 1.4l petrol manual and was wondering if you'd know the correct part number for the compatible pedal. Thanks in advance!
Hi there, I wouldnt be just 100% sure of the part number for the C2 but have a look on Catcar.info if you take a look through the part diagrams on there you should be able to see whatever option correlates to your spec of car and the pedal you are looking for. Its one of those sorts of searches where your best making a cup of tea first and enjoying your time at the computer.
I am really not too sure, i watch Allen Millyards videos and he has a night time camera to spot them coming out at night. Its not the first time ive seen a hedgehog at day time.
Hi, it is not something i ever did to my old 406s as both had cruise control However i do remember the owners club had a great guide on it www.406oc.co.uk/viewtopic.php?t=20756 You will need PP2000 to reprogram the car yes.
It is replaced to allow the speed limiter function to work The standard accelerator does not have the indent to bypass the speed limiter, it is replaced with one that has the indent to allow the speed limiter to function
Hi, great video. Looking to do this myself as I couldnt get hold of a cruise control version of the XTR. Any links to the cable to connect laptop to OBD2 connector please ? tried ebay and amazon but all I seem to be getting is audi VW ones and not sure they will work.
Hi, thanks for the comment. It is strange that the XTRs did not all get cruise control, especially when it probably only cost pennies for PSA to add. The cable is called Diagbox, search for it, all the usual websites have plenty of choice.
@@peugeotCitroen2CV Hi, does the ignition need to be on when activating the cruise control in the ECU ? Watched the vid a few times now and you seem to turn it off without metioning turning it on . Hope it makes sence.
@@davecrossling8289 Hi Dave Yes the ignition generally stays on although you may be prompted at certain times to turn it off and wait a set amount of seconds. It will guide you through that process.
Hi quick question. I got my Citroen xzsara picasso 2007 second hand. It already had the CC control stick installed when I got it but the CC has never worked. After watching your vid I've now seen that the accelerator pedal isn't LVVD, and I have no diagnostic equipment to check if the clutch and break switches are correct. Do you think there's a change seeing as it should already be enabled on the car, if I just switch the parts for the correct parts as listed in the video, that it might start working? Or will I still need the lexia equipment to enable it? The mist frustrating thing is, I'd assume a light would come on the dash but the equipment not work because I've got the wrong parts, but that doesn't seem to work. Could again that be due to it not recognising the wrong parts therefore just not working all together? Any help much appreciated. Cheers
Hi there I am not sure if the xsara picasso supports the speed limiter functionality, so i doubt there is a need to look for the LVVD pedal, but some may have had cruise control. You would still need lexia to enable any of the functions. If you had lexia you could at the very least see if the command is being sent to activate cruise control. Ask on the citroen owners club or a specific xsara picasso one there may be someone who has lexia, its not too expensive to buy from ebay but im not 100% sure about versions anymore as i now use a device which works with all cars so havent really had much cause in the past few years to use my old xp laptop and lexia dongle.
@@1Dipped Hi there, not for the launch device i bought it off Facebook marketplace second hand. The Diagbox was off ebay many years ago, lots of them still available now. You may need to join the forums to see what is the best version to get as ive not used the diagbox machine in some time.
@@peugeotCitroen2CV hi mate sorry to bother you again so if i just want the cruise control do i still have to change the pedal or do i need to just instal the stalk and get somebody to programme it thanks
thank you very much, I have a 2012 van and unfortunately I can not change the cruise control settings in the ecu the engines in Bsi managed without a problem
@@michalk5506 I had a similar issue. I had someone call round to get their 2012 van cruise control added, but i was unable to do it that day. The issue i believe is that my laptop was running one of the later diagbox updates, apparently it's better to work on an earlier version of diagbox as it will let you into the ECU settings. Is your van running a bosch or siemens/continental ECU? I have installed an earlier version on a seperate laptop but the chap who owns the van has not yet been back to try that out.
@@peugeotCitroen2CV I do not know what ECU I have, it is my father's car and I will have access only next weekend. My diag is v7.83, I got info that I should have max v7.53, I will try to get it. Thank you very much for the answer
We found the setting in bsi and changed it to cruise and speed limit. But in the engine ecu tab i cant find any speed limiter och cruise control to activate 🤔
@@Zenoy I think there has been issues with some of the more up to date versions not permitting certain functions. Did you put on the extra updates that the CD had?
It is demonstrated working towards the end of the video. However to put it in writing the speed limiter will prevent the vehicle from going over the set speed. Set it to 30mph driving through a town and it will not accelerate above it. There is a detent in the accelerator pedal so if you push hard on it the vehicle will override the speed limiter which may be required. A downside to this particular system compared to some more modern ones is that it will not use the brakes to maintain the speed, my dad has a 2015 Mercedes C class which will brake the vehicle which is particularly useful if driving downhill. It will also engage the brakes if you turn on the speed limiter, if you engage the speed limiter in this berlingo the speed display will flash until you bring the vehicle down to that speed.
@@MrGuvEuroman Yes if its not changed you can still have just cruise control Although i find myself using the speed limiter much more than the cruise control, but there are plenty out there who do not regard it as necessary
@@peugeotCitroen2CV Thank you this has been a great help, I found the perfect belingo with no cruise I was going to forget it but seeing how easy it is I going to buy it. 😀
I've done this upgrade on all my partners/berlingos since 2008 and it's worked on all of them (as long as you enable the right options on diagbox!!)
I bet the drivers of these have been happy as a result
Thank you for being so beautifully thorough ☺️🥰
Thanks for the comment glad you enjoyed the video.
Absolutely the best instructional video 😌
I was able used a large russel honbs kitchen knife to make the vertical cuts in the cowling by levering/rocking the knife straight down, then the horizontal 'cut' going back n forth with extreme bending/folding of the plastic until it snapped off.
Just used your video to fit the pedal and control for cruise control, took me maybe 40mins to do, brilliant truly guide. My only comment was the cable onto the pedal had virtualy no slack, still managed it no problem but everyone be awear. Now to get it enabled...
did you get it enabled?
A good way of making the better looking VTR as good as an XTR!
I never noticed a huge difference to be honest, the XTR has more of an off road look about it? They are all still rather boxy looking vans.
@@peugeotCitroen2CV I much prefer the vtr's colour coded bumpers etc. Must be the only car where the higher spec has less paint
Taking delivery of the parts tomorrow (pedal and stalk). Watched this video over and over again so hopefully tomorrow’s installation will go off without a hitch. Will report back.
Thanks again for the PM’s on messenger @peugeotCitroen2cv.
Following your instructions and got cruise and speed limiter working spot on.
My 2012 Berlingo Multispace 1.6 hdi 8v with EDC17 engine ECU and 9HP wouldn’t work on any other version of Diagbox other than 7.02.
If you get ‘invalid key’ and you drive a 2012 downgrade Diagbox to 7.02.
7.01 - did not work
7.02 - WORKED
7.57 - did not work
7.58 - did not work
7.62 - did not work
7.66 - did not work
No version between 7.66-7.83 worked
7.82 - did not work
7.83 - did not work.
7.02 was the only way to go in case you get stuck. Thanks again for the info and the video. Now tempted to try your other videos :)
Next tasks for me are:
- front top strut mounts
- fuel leak from near fuel rail
- dpf
- blower fan motor
That EML I had in the video I sent you was to do with the DPF blocking throwing up other random codes. If you kick it too hard it does that for me occasionally. I need my dpf erased 🤣
Need my blower fan motor replaced. Relay is fine. No blow on any settings. Still get a residue amount of heat or cold depending on the setting but still not blow.
Know any easy ways of getting to the blower motor? I have a vague idea of it being under the steering wheel and above the pedals but by Christ is it tight.
That old car does 18 months ago. My new car got wrote off so I’ve picked up a Peugeot partner 2012. Is the process the exact same?
I took my 2013 Partner Teepee to a Peugeot main dealer last year, to get cruise retrofitted. They were confident they could do it, checked, installed & programmed everything, but then found on the roadtest that the chosen speed wasn't retained - it flashed back to 10mph or something. After 2 days investigation they admitted defeat, and refunded me what I'd paid for the work. They did mention that there was a fault code related to the resistance of the accelerator pedal (rheostat) which they thought could be relevant - quoted £400 for replacement! As the cc switch is still fitted (Thanks Peugeot!), it would be great to get it working. I did buy a second -hand accelerator pedal on Ebay, but never got round to fitting it. Is swapping the pedal out worth a try - or is the problem more likely to be with the programming?
Interestingly there is an additional part/clip that holds the stalk in place which I discovered when taking a stalk from a factory fitted cruise van.
An excellent guided video! Hoping to tackle this next weekend.
I wonder if you may be able to help. What's the software/tool you used at the beginning to diagnose whether your brake and clutch pedals had the appropriate switches?
Thanks works great at the new version 9.1.1
As we say, dead on man! Now I want to ask you a question, I have a 2014 Citroen Dispatch and I would like to change the twin seat to a single do you know if I can and if so which donor vehicles will be suitable.
Haha they say that here also. Where abouts are you from?
The dispatch, not entirely sure, was the E7 taxi version equipped with twin front seats. I think there is a dispatch/boxer (is that the peugeot equivilant?) facebook group ask on there they should be able to give you ideas of what seats to use.
@@peugeotCitroen2CV The Occupied six Counties!☘ Goraith maith agat
Hello again, I have been trying to get my cruise control working on the Citroen Dispatch 2014 the limiter works and when the diagnostics are connected cruise works intermittently. The guy who done the testing has checked everything on the computer but it still wont work, do you know what else I should try.
What an excellent video.
Thanks for the comment
what is the software you use?
Hi, it was a copy of Diagbox available from ebay.
@@peugeotCitroen2CV thx !, windows 7 or 10 what windows do u have?
@@realcon5086
Mine is on an old XP laptop
Tbh i dont actually know the exact version its on, i bought it from ebay about 5 years ago initially i updated to the newest version on the CD but ended up having to going back a few versions
I dont use it as much anymore as i have a tablet that does all cars. Only the odd PSA car now, a few weeks ago it was an early xantia abs fault
@@peugeotCitroen2CV thx mate for reply, i installed thw software but doesnt work, it says i need xp or windows 7, gonna try today the virtual windows xp.
Hello thank you for the post. I have done the cruise control part(limiter not required) of the install on my 2008 xtr berlingo, and my mechanic has enabled cruise on the bsi and the ecu, following appropriate steps. I am getting a message on the centre console saying 'cruise control impossible' when trying to activate the cruise control. Is this something you have come across or know how to resolve?
Many Thanks
Matt
Hi there
I came across a mates berlingo that would not let me change the setting on the ECU, it turned out the version of diagbox i was using was too new and i had to install the older version. Are you seeing the cruise control symbols in the LCD screen within the instrument cluster?
Hi thank you for your reply. I managed to get the cruise control working, as you said it was the version of diagbox that was the issue. I do now have another issue though. I purchased the accelerator pedal for the speed limiter, however the new one has 6 electrical pins, whereas the original only has five, with the plug also accommodating five pins. My cable doesn't have the one with the orange clip. Is there a different pedal available with 5 pins or maybe a 5 pin to 6 pin adapter?
Many Thanks
Matt
@@matthewilett6174 Hi there matt
There may be different accelerator pedals for different years, do you see the build code sticker on your berlingo? Google Citroen RPO number to see examples of what i am asking, let me know what your RPO number is and i will see what i can find in terms of part numbers. The 5 and 6 pin pedals will not be cross compatible you will need a different pedal to work with your ecu.
Hi
Thank you so much for your help by the way I really appreciate it.
The RPO number is 11613FV
Hey, mate!
I've got a 2006 Citroen C2 VTR 1.4l petrol manual and was wondering if you'd know the correct part number for the compatible pedal.
Thanks in advance!
Hi there,
I wouldnt be just 100% sure of the part number for the C2 but have a look on Catcar.info if you take a look through the part diagrams on there you should be able to see whatever option correlates to your spec of car and the pedal you are looking for. Its one of those sorts of searches where your best making a cup of tea first and enjoying your time at the computer.
A bit off topic but why was the hedgehog out in daylight? 😮
I am really not too sure, i watch Allen Millyards videos and he has a night time camera to spot them coming out at night. Its not the first time ive seen a hedgehog at day time.
I want to do the same to full-mux 406 (Cruise Control only). I activated it in BSI but it still doesn't work. Do I need to reprogram ECU as well?
Hi, it is not something i ever did to my old 406s as both had cruise control
However i do remember the owners club had a great guide on it
www.406oc.co.uk/viewtopic.php?t=20756
You will need PP2000 to reprogram the car yes.
@@peugeotCitroen2CV Thank you!
@Jerrod Dunsing lulw nice bots mate.
Hello, may I ask why is the accelerator pedal replaced? Definitely explains it but I can't understand, thanks.
It is replaced to allow the speed limiter function to work
The standard accelerator does not have the indent to bypass the speed limiter, it is replaced with one that has the indent to allow the speed limiter to function
So for only cruise control you don't need the accelerator pedal?
Can u use Glw pedal?
Which diagnostic tool you used to check live stream? Will this be same for 2015 Peugeot partner tepee, Thanks
Diagbox on his windows laptop ( as mentioned in the video) and yes it's the same settings as per other TH-cam videos
@Hellofa6ird i understood diagbox, i was asking about the red coloured scanning tool. Thanks
Hi, great video. Looking to do this myself as I couldnt get hold of a cruise control version of the XTR. Any links to the cable to connect laptop to OBD2 connector please ? tried ebay and amazon but all I seem to be getting is audi VW ones and not sure they will work.
Hi, thanks for the comment.
It is strange that the XTRs did not all get cruise control, especially when it probably only cost pennies for PSA to add.
The cable is called Diagbox, search for it, all the usual websites have plenty of choice.
@@peugeotCitroen2CV Hi, does the ignition need to be on when activating the cruise control in the ECU ? Watched the vid a few times now and you seem to turn it off without metioning turning it on . Hope it makes sence.
@@davecrossling8289 Hi Dave
Yes the ignition generally stays on although you may be prompted at certain times to turn it off and wait a set amount of seconds. It will guide you through that process.
Hi quick question.
I got my Citroen xzsara picasso 2007 second hand. It already had the CC control stick installed when I got it but the CC has never worked. After watching your vid I've now seen that the accelerator pedal isn't LVVD, and I have no diagnostic equipment to check if the clutch and break switches are correct.
Do you think there's a change seeing as it should already be enabled on the car, if I just switch the parts for the correct parts as listed in the video, that it might start working? Or will I still need the lexia equipment to enable it?
The mist frustrating thing is, I'd assume a light would come on the dash but the equipment not work because I've got the wrong parts, but that doesn't seem to work. Could again that be due to it not recognising the wrong parts therefore just not working all together?
Any help much appreciated. Cheers
Hi there
I am not sure if the xsara picasso supports the speed limiter functionality, so i doubt there is a need to look for the LVVD pedal, but some may have had cruise control.
You would still need lexia to enable any of the functions. If you had lexia you could at the very least see if the command is being sent to activate cruise control.
Ask on the citroen owners club or a specific xsara picasso one there may be someone who has lexia, its not too expensive to buy from ebay but im not 100% sure about versions anymore as i now use a device which works with all cars so havent really had much cause in the past few years to use my old xp laptop and lexia dongle.
Hi does the abs pump need to be changed when retrofitting cruise control to a 2010 Citroen Berlingo multispace xtr.thanks
What is the machine you use to code the car ?
Hi there,
Diagbox for PSA vehichles, or i use a launch device which works with different cars
@@peugeotCitroen2CV you dont have a link to it do you ?
@@1Dipped
Hi there, not for the launch device i bought it off Facebook marketplace second hand.
The Diagbox was off ebay many years ago, lots of them still available now. You may need to join the forums to see what is the best version to get as ive not used the diagbox machine in some time.
@@peugeotCitroen2CV hi mate sorry to bother you again so if i just want the cruise control do i still have to change the pedal or do i need to just instal the stalk and get somebody to programme it thanks
@@1Dipped for cruise only you don’t need the pedal but still need the setting changed with diagnostic equipment
Hi, what year of production of the car?
This one is a 2011, although the B9 was produced from 2008 to 2018
thank you very much, I have a 2012 van and unfortunately I can not change the cruise control settings in the ecu the engines in Bsi managed without a problem
@@michalk5506
I had a similar issue.
I had someone call round to get their 2012 van cruise control added, but i was unable to do it that day.
The issue i believe is that my laptop was running one of the later diagbox updates, apparently it's better to work on an earlier version of diagbox as it will let you into the ECU settings. Is your van running a bosch or siemens/continental ECU?
I have installed an earlier version on a seperate laptop but the chap who owns the van has not yet been back to try that out.
@@peugeotCitroen2CV I do not know what ECU I have, it is my father's car and I will have access only next weekend. My diag is v7.83, I got info that I should have max v7.53, I will try to get it. Thank you very much for the answer
What diagnostic program do you use?
Diagbox, have a look on ebay for it, there is plenty of choices for it.
We found the setting in bsi and changed it to cruise and speed limit. But in the engine ecu tab i cant find any speed limiter och cruise control to activate 🤔
@@Zenoy What version of Diagbox are you using?
@@peugeotCitroen2CV 7.57
@@Zenoy I think there has been issues with some of the more up to date versions not permitting certain functions. Did you put on the extra updates that the CD had?
What does the speed limiter do?
It is demonstrated working towards the end of the video.
However to put it in writing the speed limiter will prevent the vehicle from going over the set speed. Set it to 30mph driving through a town and it will not accelerate above it.
There is a detent in the accelerator pedal so if you push hard on it the vehicle will override the speed limiter which may be required.
A downside to this particular system compared to some more modern ones is that it will not use the brakes to maintain the speed, my dad has a 2015 Mercedes C class which will brake the vehicle which is particularly useful if driving downhill. It will also engage the brakes if you turn on the speed limiter, if you engage the speed limiter in this berlingo the speed display will flash until you bring the vehicle down to that speed.
@@peugeotCitroen2CV ahh so pedal change is only for speed flash?
@@MrGuvEuroman
Yes if its not changed you can still have just cruise control
Although i find myself using the speed limiter much more than the cruise control, but there are plenty out there who do not regard it as necessary
@@MrGuvEuroman Correct
@@peugeotCitroen2CV
Thank you this has been a great help, I found the perfect belingo with no cruise I was going to forget it but seeing how easy it is I going to buy it. 😀