I really like how to played the animations over and over again for a few seconds, really helped me understand it more. This is the perfect valve video.
Thank you for making this video! I really appreciate the way you present the material. Your descriptions are so straight-forward and concise. Please keep producing!
Just a note... This is all for low pressure systems. When your system and/or differential pressures are in the thousands, ball and butterfly valves disappear, and globe and gate valves are the rule. Also, cheap globe valves may be intended to be directional. But the higher grade models will gladly hold several thousand psid indefinitely, w/o leaks. Dual disc gate valves will hold their pressure either way too. In many cases, due to the high effort necessary to operate valves under high pressure, pilot valves are part of the system as well, and are almost always some form of globe or needle valve.
@@kinanfadel1116 servicing the valves is a whole different discipline than purchasing. I have no clue what the commercial versions cost. But I'm quite sure that the globe valves are among the more expensive, possibly only being exceeded by the double disc gate valves. They remain in use, not because they're cheap, but because when you need to control or regulate several thousand PSI differential, everything else fails.
Ball valve not used for control flow . Ball valve is used for on/off operation . And specifically for frequent use, as found in a truck of water tanker .
#valves #plants #processcontrol #processes #gatevalve #controlvalves #pressurevessels #saftevalve A valve is a mechanical device. It has a moveable mechanism that can open-close the passages in the body. A valve Fluid’s flow open-close even completely controls, through the pipelines, Vessel, Equipment, and Machine. techproces.com/valves/
Great information and appreciated effort, i hope you keep simplifying and illustrating the way you are doing. Just a small remark, if you could improve the audio quality of the video that would be great, many thanks for your effort and time.
In the globe and solenoid valve the flow, as shown, is in the wrong direction. The flow should enter the valve from the top. If it enters from the side below the plug / disc, there's the risk pressure will force the plug / disc up. Whereas if the flow enters the top side, pressure will keep the plug / disc down
hi thanks for the video, but i was looking to see how a foot valve works? seems the one i have needs to push the guard out to suck the water in? and logic will not allow me to understand this? if you can I would love a explanation and a video would be really great.
You mentioned that Globe Valves should never be used as shutoff valves in between a piping system. I'm sure this will make sense, but could you clarify why this is the case? ( thanks )
Very nice but I have question if we have Gate valve on our pipe line we have to set one globe or ball valve to decrease flow or pressure because you mentioned that gate vale just work to stop the flow. Please kindly answer this question
Great videos！！！ These videos are very good learning material. Can i record your videos and post them on other chinese video platform？Since chinese can't watch youtube. I will of course annotate these videos are made by "ExplaninFull" and i will also show a link of your youtube channel when i post the videos. If you agree that, i will be grateful !!
![ลองสุ่มไอโฟน 990 โกงมั้ย? [ โกงมั้ยครับ ep.101 ] | DOM](http://i.ytimg.com/vi/bfsWe0j492k/mqdefault.jpg)
I really like how to played the animations over and over again for a few seconds, really helped me understand it more. This is the perfect valve video.
Excellent !!
People like simplicity, simple explanations in simple words with simple drawings and good animation....excellent !
Very well made video. The diagrams/animations helped me understand in a second what I failed to understand by reading my textbook. Thank you.
Thank you for making this video! I really appreciate the way you present the material. Your descriptions are so straight-forward and concise. Please keep producing!
Just a note...
This is all for low pressure systems. When your system and/or differential pressures are in the thousands, ball and butterfly valves disappear, and globe and gate valves are the rule.
Also, cheap globe valves may be intended to be directional. But the higher grade models will gladly hold several thousand psid indefinitely, w/o leaks. Dual disc gate valves will hold their pressure either way too. In many cases, due to the high effort necessary to operate valves under high pressure, pilot valves are part of the system as well, and are almost always some form of globe or needle valve.
it is not true at all, bro, in aircraft, most buffterfly valve is used for high pressure system
Thank you sir , But would you please tell us about the differences in price among all these kinds of valves ? .
@@kinanfadel1116 servicing the valves is a whole different discipline than purchasing. I have no clue what the commercial versions cost. But I'm quite sure that the globe valves are among the more expensive, possibly only being exceeded by the double disc gate valves. They remain in use, not because they're cheap, but because when you need to control or regulate several thousand PSI differential, everything else fails.
Fantastic stuff. Anything with moving graphics like this I find hugely helpful. Many thanks ExplainFull.
The ball valves are used to control the flow of liquids.
Very nice presentation, thanks for sharing.
Ball valve not used for control flow . Ball valve is used for on/off operation . And specifically for frequent use, as found in a truck of water tanker .
Thanks for this video. I've always wondered how these valves actually work. And thanks to you, now I know.
please come back and make more videos, the few you got are awesome!
Thank you, simplicity is priceless!
Pretty concise and simple!
Check valves are life savers!!
Superb and easy explaination ..please make videos on flange
I'm a valve tech ,helpful information
I liked the final example: pressure valve illustration.
#valves #plants #processcontrol #processes #gatevalve #controlvalves #pressurevessels #saftevalve
A valve is a mechanical device. It has a moveable mechanism that can open-close the passages in the body. A valve Fluid’s flow open-close even completely controls, through the pipelines, Vessel, Equipment, and Machine.
techproces.com/valves/
I liked the small test at the end of video
Excellent and informative video!
Amazing explanation!!!
GREAT VIDEO!
thank you!
Great animations
Great work 👍
good stuff
Thank you . Very nice and helpful.
Great information and appreciated effort, i hope you keep simplifying and illustrating the way you are doing.
Just a small remark, if you could improve the audio quality of the video that would be great, many thanks for your effort and time.
Excellent, excellent video. Two thumbs up.
James Rayburn
Lovely animation
Very Good .
Great video.
very very useful video bro, and make more videos. God bless you
Nice video.
well done
Really very useful.
Very good, thanks!
Thank You , It was so benefitious
very good video, thank you :)
Very well put together video, thanks alot!
Excellent explanation.....
Good 👍
Very nice sir...So useful
thank you for your explain. this is awesome video
cool clearly👍
In the globe and solenoid valve the flow, as shown, is in the wrong direction. The flow should enter the valve from the top. If it enters from the side below the plug / disc, there's the risk pressure will force the plug / disc up. Whereas if the flow enters the top side, pressure will keep the plug / disc down
simple explain , very good
I need a valve that will hold a very small vacuum. Will a ball valve work?
Very informative
thanks for the video! I have a question: Can I regulate the water intensity with a solenoid valve?
Thank you sir , But would you please tell us about the differences in price among all these kinds of valves .
This is great. Thank you!
Thanks for sharing its useful
Amazing
hi thanks for the video, but i was looking to see how a foot valve works? seems the one i have needs to push the guard out to suck the water in? and logic will not allow me to understand this? if you can I would love a explanation and a video would be really great.
I hope you do a lot more video
You mentioned that Globe Valves should never be used as shutoff valves in between a piping system.
I'm sure this will make sense, but could you clarify why this is the case? ( thanks )
maybe because a backwards pressure can damage the seals?
@@MrSmith-rk4jq Yes he even mentioned that
Thank you.
Excellent...
Usefull
Thanks very helpful
Well made!
Thank you it's super helpfull
absulately briliant. thanks
Very nice but I have question if we have Gate valve on our pipe line we have to set one globe or ball valve to decrease flow or pressure because you mentioned that gate vale just work to stop the flow. Please kindly answer this question
Well done! Thank you.
What do you use to make these awesome videos? I use PowToon
Pow Genius i use Poon Tang.
Mark Cuckerberg Thanks for replying!
can shut off valve or a mini ball valve replace , Non return valve, for air filling .
About half of all this info. is correct.
What exactly is in the incorrect half?
Needel valve function
Super
Thankyou
Why should the globe valve not be used in a piping system?
Thumb up :)
appreciated thanks
Great videos！！！ These videos are very good learning material. Can i record your videos and post them on other chinese video platform？Since chinese can't watch youtube. I will of course annotate these videos are made by "ExplaninFull" and i will also show a link of your youtube channel when i post the videos. If you agree that, i will be grateful !!
Well done 👍
But your voice is sleepy .
#sir please one video make on hvac compressor and motor part winding cannection.
I HAVE A QUESTION. WHAT IS THE "CLASS" IN VALVES CHARACTERISTIC? FOE EXAMPLE GATE VALVE CLASS 1500.
That's pressure rating, I guess. More the class, more the pressure it can be used in.
Pressure class. 1500# is the ANSI standard
You may have noticed the laptop is actually on my lap! A No No!!!
podrías traducirlo en castellano ?
Не. уя не понятно но очень итересно
Explain Tamil
Thank you.