Hi Curtis, I am one of your MaxiSys Elite clients. The terminology used here is "inhaling" the data from the other modules. The F-Series trucks are a bit different than the other vehicles in regards to reprogramming .
I have the old one and I’ve got a new one that is reprogrammable.. the old one is got got 2 bad spot in the broad when I hook a code reader on it It say the truck is safe to drive so how would I get the new one programmed I can’t the the info off the old one
The Tear Tag is typically a four-digit identifier of the PCM. It can be found on the label on the vehicle PCM, on the PCM's plastic housing , or on the shock tower or passenger's side door jam . It can also be found on the inner fenders or strut tower, or in the door jams . If the Tear Tag number is not listed, enter your full Vehicle Identification Number (VIN) at the Ford Tech info service website ( as build data)
HI John. If you want me to teach you step by step you can book a consultation at my website auteltech.co.za . Click the j2534 training and consulting. The training also comes with a OEM ford Information account
Hi, I need a help with my 2104 Ford Focus TRANSMISSION CONTROL MODULE AND ELECTRIC CONTROL MODULE. I JUST USED MODULES that need to be reprogrammed. Please contact if you can.
Hi Master i have a big big big cuestión I hope you can help me, I have 2 AUTEL Scan ms908 and ts608, I buy in USA and I activated in USA and I used this tools in USA for 2 years, I think go back to Mexico my country, now The cuestión, Wat happens if I try to work in Mexico with my AUTEL Scan tools. in Mexico have a lot different car models and brands different and other same to USA, #1 my Scan tools work for this Mexican vehicles , or I need make 1 update to my tools for México? # 2 ir my AUTEL Scan tools is not working at all en México? .
Hi Dereck, I think I have a video of me doing a vin writing procedure on the ms906BT. I just wanted to show people that sometimes the autel wont have these featers. When its on the maxisys its realy easy to do
I dont know because I haven't had any of my clients call me to log in their devices and submit the issue to autel's engineers. What you need to do is contact who you purchased the tool from or Autel New York. Go to the vehicle and have them remote in and submit a data logging. If your not able to do this then they will not know that there is a problem. I deal with this software issue alot thats the process I do to fix the issue.
Hey Curtis, I have a 2009 Kia Borrego 4.6L V8. My original ECM electronics board burned out. I bought an exact part number used ECM. Is there anyone or anyway to rewrite my VIN on the used ECM? Please help! Thank you.
Hey Curtis, can you please make a video about the new Maxisys ULTRA an its capabilities? Right now I'm about to purchase the Maxisys Elite and im not sure whether I should wait for the new Maxisys devices since they will be launched in April or maybe a bit later. Thank you!
@@AutelConsultancy Unfortunately not. Im living in germany and the european supplier couldn't give me any informations at all. So i contacted the US supplier and they couldn't give me infos either.
It is kind of strange because the device is about to be released (so it should exist physically at least by now) and no one can tell me the capabilities.
@@cyberdarknes Yea , the did the same thing with the ADAS systems. And they are still working on some features so they are not going to release anything until its been tested and confirmed
Any idea why I wouldn’t be able to enter the full VIN in the programming process within the Ford software? I’ve got a 2007 F350 that I’m programming a PCM that was replaced and the original isn’t available. Thanks
Is the J2534 module imperative to change a vin or is it vehicle dependant? I have a 2008 Nissan Note,(UK) that I wish to change the ECU to a used replacement unit. I still have the original ECU.
@@lubinpetit1831 Hi, but the ECU I have is a JDM unit, that does not have NATS. I have already tried it in my car, the car just turns over but will not start.
Is it the same way if you got a program the keys too into it because I have that I'll order the j2534 I also have to reprogram the keys is that correct let me know when you get a chance
Hey Curt. Josh P here. One of your clients. How much is Fords programing software? I have an 02' Expedition coming in monday for a pcm replacement. I've sourced a used pcm. I'm looking forward to putting this to the test
Hey Josh. Do you have the Orignial PCM ( Keep it if you can) Ford is 50 USD for 72 hours. Did you check if autel has the Programmable Module Installation? if it does ( and you have the orginal module) then we will be able to just use your autel. Let me know
@@AutelConsultancymy truck burnt down it’s a 2005 f150 so I bought a 2008 truck to fix it but now that it’s fixed I’m having trouble with smog bc pcm for my 2005 burnt up an melted so my truck basically thinks it’s a 2008😊
Ok, just find out how much they quote you because I get alot of clients who send their work to dealers or mechanics and the price they quote them is the price of the tool.
@@uthmansalaudeen4260 Hello, I dont know because we have 4 different tools that could solve this problem . If you want me to align you with the right tool you should book the diagnostic tool consultation service on my website auteltech.co.za
Are we able to use ford ids and autel j2534 for as built data? For example I have a 2017 ford mustang flood damage bcm so i read the bcm mcu on the bench and wrote to the donor. Now car starts but I have faults for module configuration incomplete. It would have been better to program donor bcm with asbuilt data if I'm capable with j2534.
The Auto MP808 Has the ability to Reprogram modules on Fords. It works for all 3 of my vehicles. 2000 Focus ZX3, 2004 F-150 STX 4x4, & 2009 Escape XLT. I almost didn't purchase this scanner because of this and Autel claimed on their website that it didn't do it but I took a chance on it and I was surprised to find the programable modules feature on my Scanner. Haven't actually tried the feature out yet but I will soon because I need to replace a bad RCM on the Focus.
You are very fortunate. State one tools dont have alot of coding on them but enough for vehicle from 1996 to 2010 . I think when you get into new models it might be limited in coding . But im glad it worked out for you.
hello. have a ford mustang 2002 all keys lost. went im try to programing the new two keys the car only get one off two for any reason dont take the another keys. can you plz help me
Hello, its hard to pin point the situation as I would need to log in remotely to do some test. But on the surface it may be one of the keys your using is problematic. You can try purchasing another key and see if thats the solution.
Does this work with a newer model like 2011 fusion cause I tried and ran into a problem but maybe because I wasn't turning on the key after I wrote the vin?
It should work. I know on newer vehicles the manufactures kind of shy away from us using second hand modules. But it should work for that vehicle. Im not sure if there is something wrong with the module you purchased . Check to see if it has the right tear tag information
@@marcopisanti8932 Ive managed to use windows 7 . If the operating system was not compadible I dont think you would be able to install/ load the software . You are probably going to need someone to log in and diagnose / trouble shoot what the problem is. It could be a variation of things that to difficult to diagnose with out inspecting
@@AutelConsultancy ok so after 2 days of trying the problem was the windows 7 wasn't connecting to the server I tried a windows 10 PC and was able to proceed to module programming (PROBLEM SOLVED)
Hi Driver, Yes its been a while.. Ive been doing alot of training over the past few months with the new technologies coming out. Also trying to consult my clients at the same time. But ill try to post more
![[TH] FS vs BME - VCT Ascension Pacific - Lower Bracket Final](http://i.ytimg.com/vi/wnygqsR2Fig/mqdefault.jpg)
Well presented, Sir!!!
Hi Curtis, I am one of your MaxiSys Elite clients. The terminology used here is "inhaling" the data from the other modules.
The F-Series trucks are a bit different than the other vehicles in regards to reprogramming .
I have the old one and I’ve got a new one that is reprogrammable.. the old one is got got 2 bad spot in the broad when I hook a code reader on it It say the truck is safe to drive so how would I get the new one programmed I can’t the the info off the old one
Thank you for your videos!
Dont exaggerate your obviously paid
Very valuable informations! Looking forward for the next videos!
Hey brother, new with ford can you let me know what a Tear Tag is and where can I find it??
The Tear Tag is typically a four-digit identifier of the PCM. It can be found on the label on the vehicle PCM, on the PCM's plastic housing
, or on the shock tower or passenger's side door jam . It can also be found on the inner fenders or strut tower, or in the door jams . If the Tear Tag number is not listed, enter your full Vehicle Identification Number (VIN) at the Ford Tech info service website ( as build data)
Will it Re-write a Vin to a used Chrysler Anti lock brake controller ?
Hi Curtis which autel is best for Australian made Ford ??.James
That was great thank for video
My Pleasure.
Hi , would maxisys MS908S will be capable to programme a used ecu on Ford Focus 1.4 petrol 2003 Uk registered? Thank you
Can a car start the engine if the vin of the ECM is not changed?
Only if you program the keys to the new/used pcm
Hi I buy a 906 bt pro but I can rewrite vin in a ford f 350 2006 , one can i do
Do it
Hi how can I buy ford ids and use with my im608
HI John. If you want me to teach you step by step you can book a consultation at my website auteltech.co.za . Click the j2534 training and consulting. The training also comes with a OEM ford Information account
Hi, I need a help with my 2104 Ford Focus TRANSMISSION CONTROL MODULE AND ELECTRIC CONTROL MODULE. I JUST USED MODULES that need to be reprogrammed. Please contact if you can.
Hello, you can book a j2534 training and consulting session on my website auteltech.co.za
Did you sort your problem out
I need update for my elite.do you sell updates?
I normally sell them to my clients but I can organize one for you. They go for 1200 USD
Good morning
Hi Master i have a big big big cuestión I hope you can help me, I have 2 AUTEL Scan ms908 and ts608, I buy in USA and I activated in USA and I used this tools in USA for 2 years, I think go back to Mexico my country, now The cuestión,
Wat happens if I try to work in Mexico with my AUTEL Scan tools. in Mexico have a lot different car models and brands different and other same to USA, #1 my Scan tools work for this Mexican vehicles , or I need make 1 update to my tools for México? # 2 ir my AUTEL Scan tools is not working at all en México? .
Why not show how to write the VIN with the Autel rather than the on line Ford software, I know it is easy on the Elite and 906bt
Hi Dereck, I think I have a video of me doing a vin writing procedure on the ms906BT. I just wanted to show people that sometimes the autel wont have these featers. When its on the maxisys its realy easy to do
Will the Autel j2534 elite box do this?
Yes
I have an issue Autel im 508 and 608 is not able to add a key on a 2023 ford transit and a 2024 GMC Sierra….what is Autel going to do with this issue.
I dont know because I haven't had any of my clients call me to log in their devices and submit the issue to autel's engineers. What you need to do is contact who you purchased the tool from or Autel New York. Go to the vehicle and have them remote in and submit a data logging. If your not able to do this then they will not know that there is a problem. I deal with this software issue alot thats the process I do to fix the issue.
Hey Curtis, I have a 2009 Kia Borrego 4.6L V8. My original ECM electronics board burned out. I bought an exact part number used ECM. Is there anyone or anyway to rewrite my VIN on the used ECM? Please help! Thank you.
Hey Curtis, can you please make a video about the new Maxisys ULTRA an its capabilities? Right now I'm about to purchase the Maxisys Elite and im not sure whether I should wait for the new Maxisys devices since they will be launched in April or maybe a bit later. Thank you!
Hi Cyber, your supplier doesnt have any info on the machine?
@@AutelConsultancy Unfortunately not. Im living in germany and the european supplier couldn't give me any informations at all. So i contacted the US supplier and they couldn't give me infos either.
It is kind of strange because the device is about to be released (so it should exist physically at least by now) and no one can tell me the capabilities.
@@cyberdarknes Yea , the did the same thing with the ADAS systems. And they are still working on some features so they are not going to release anything until its been tested and confirmed
Any idea why I wouldn’t be able to enter the full VIN in the programming process within the Ford software? I’ve got a 2007 F350 that I’m programming a PCM that was replaced and the original isn’t available. Thanks
Is the J2534 module imperative to change a vin or is it vehicle dependant? I have a 2008 Nissan Note,(UK) that I wish to change the ECU to a used replacement unit. I still have the original ECU.
HI Charley . I use the j2534 as a back up if the autel software doesnt have the feature. Some oem subscriptions allow vin writing, some dont.
Charley Brown vous êtes mécanicien
U dnt need a jbox to do that on those. Go in NATS there is an option for used PCM swap
@@lubinpetit1831 Hi, but the ECU I have is a JDM unit, that does not have NATS. I have already tried it in my car, the car just turns over but will not start.
Is it the same way if you got a program the keys too into it because I have that I'll order the j2534 I also have to reprogram the keys is that correct let me know when you get a chance
Can I do this on a Volvo XC90 with the maxi 808
Hey Curt. Josh P here. One of your clients. How much is Fords programing software? I have an 02' Expedition coming in monday for a pcm replacement. I've sourced a used pcm. I'm looking forward to putting this to the test
Hey Josh. Do you have the Orignial PCM ( Keep it if you can) Ford is 50 USD for 72 hours. Did you check if autel has the Programmable Module Installation? if it does ( and you have the orginal module) then we will be able to just use your autel. Let me know
how you getting the tear tag number if they dont have original computer
Sie could you please tell me how long this key programmer features will work i mean is it for ever or i need to purchase new updates every year?
Can it be done on 2018+ Ford model with IM608 pro? Thanks
WHAT ABOUT 2006 ESCAPE, WHERE FEPS 18V IS NEEDED IT
Sir I have problem in my Honda civic 2018 model bcm
Where are you located mine is a different year ecu shows up as a 2008 f150 buts its a 2005
I work virtually so I can be anywhere as long as you have internet access and a laptop
@@AutelConsultancymy truck burnt down it’s a 2005 f150 so I bought a 2008 truck to fix it but now that it’s fixed I’m having trouble with smog bc pcm for my 2005 burnt up an melted so my truck basically thinks it’s a 2008😊
I need help on changing vin
@@oneal2003 You can book the j2534 Training so I can consult you on my website auteltech.co.za
Not yet. I an yet to find a technician that has the tool who can do it for me in Illinois.
Ok, just find out how much they quote you because I get alot of clients who send their work to dealers or mechanics and the price they quote them is the price of the tool.
@AutelConsultancy wow. Please what could the price of the tool be.
@@uthmansalaudeen4260 Hello, I dont know because we have 4 different tools that could solve this problem . If you want me to align you with the right tool you should book the diagnostic tool consultation service on my website auteltech.co.za
Je savoir si la im608 j2534ecu peut programmé les calculateurs
Are we able to use ford ids and autel j2534 for as built data? For example I have a 2017 ford mustang flood damage bcm so i read the bcm mcu on the bench and wrote to the donor. Now car starts but I have faults for module configuration incomplete. It would have been better to program donor bcm with asbuilt data if I'm capable with j2534.
You can use Forscan to write the As-built data with no problems
Hey Curtis, i have a project..finished except for PCM..Have 2011 platinum 3.5, changed to 5.0...any recommendations on pcm and tear tag.
you need hp tuner
GOOD VIDEO,,,,,,,,,,TNX
Hello, what if my IM608 doesn't have the programming box in the main menu?
Just has Diagnos,Hot function, vehicle profile
It's a 2015 chevy captiva
The Auto MP808 Has the ability to Reprogram modules on Fords. It works for all 3 of my vehicles. 2000 Focus ZX3, 2004 F-150 STX 4x4, & 2009 Escape XLT. I almost didn't purchase this scanner because of this and Autel claimed on their website that it didn't do it but I took a chance on it and I was surprised to find the programable modules feature on my Scanner. Haven't actually tried the feature out yet but I will soon because I need to replace a bad RCM on the Focus.
You are very fortunate. State one tools dont have alot of coding on them but enough for vehicle from 1996 to 2010 . I think when you get into new models it might be limited in coding . But im glad it worked out for you.
@@AutelConsultancy thanks me too!
hello. have a ford mustang 2002 all keys lost. went im try to programing the new two keys the car only get one off two for any reason dont take the another keys. can you plz help me
Hello, its hard to pin point the situation as I would need to log in remotely to do some test. But on the surface it may be one of the keys your using is problematic. You can try purchasing another key and see if thats the solution.
Please help me
👍👍👍
What if I dont have a vin # to put in
what software did you use to program the module
Every manufacture has their own software. You would need to go to that manufactures site and download the software
Trying this on a 99 mustang and it doesn’t work
Could be a number of issues. Did you trying calling autel new york to help you diagnose the problem?
Hi Curtis
Did your client purchase ford FJDS
Or ford IDS software
FJDS
Autel Consultancy
Chris thanks
For your response
This doesn't work for me on newer years.
Probably the manufactures are getting away with used modules for new vehicles.
👍👍
Does this work with a newer model like 2011 fusion cause I tried and ran into a problem but maybe because I wasn't turning on the key after I wrote the vin?
It should work. I know on newer vehicles the manufactures kind of shy away from us using second hand modules. But it should work for that vehicle. Im not sure if there is something wrong with the module you purchased . Check to see if it has the right tear tag information
@@AutelConsultancy actually it's a 2009 but I'm wondering if maybe my system requirements are not good to use fjds because I'm using windows 7
@@marcopisanti8932 Ive managed to use windows 7 . If the operating system was not compadible I dont think you would be able to install/ load the software . You are probably going to need someone to log in and diagnose / trouble shoot what the problem is. It could be a variation of things that to difficult to diagnose with out inspecting
@@AutelConsultancy ok so after 2 days of trying the problem was the windows 7 wasn't connecting to the server I tried a windows 10 PC and was able to proceed to module programming (PROBLEM SOLVED)
I’ve been waiting for your return on TH-cam since the Black Friday
Hi Driver, Yes its been a while.. Ive been doing alot of training over the past few months with the new technologies coming out. Also trying to consult my clients at the same time. But ill try to post more
oh-dom-etter