Rotorflight 2 | SETUP SPEEDRUN | Flash to Flight in 14 Minutes! | RadioMaster NEXUS
ฝัง
- เผยแพร่เมื่อ 8 ก.ค. 2024
- Here we go, a Rotorflight 2 setup speedrun in the any% category! We get from freshly flashing the firmware to a flying helicopter in just 14 minutes!
IMPORTANT DISCLAIMER: THE FILTERS AND PIDFOB GAINS SHOWN IN THIS VIDEO MAY NOT WORK FOR YOU. AN EXTREMELY LOW AMOUNT OF FILTERING LIKE THIS EXAMPLE SHOWS REQUIRES A MECHANICALLY PRISTINE AND VIBRATION FREE HELICOPTER. THE PROPOSED PIDFOB GAINS MIGHT NOT WORK WITH YOUR PARTICULAR HELICOPTER OR INCREASED FILTER DELAY. COPY AT YOUR OWN RISK.
Relevant links to products used in this video (these are affiliate links):
Nexus: www.radiomasterrc.com/product...
RP3-H: www.radiomasterrc.com/product...
TX16S MAX MKII: www.radiomasterrc.com/product...
Rotorflight Discord: / discord
Rotorflight Website: www.rotorflight.org
Mixer Setup for further explanation on Total Blade Pitch Limit: www.rotorflight.org/docs/Tuto...
Adjustment Functions: www.rotorflight.org/docs/Tuto...
Adjusting PIDs in flight: www.rotorflight.org/docs/Tuto...
ELRS Telemetry Reuse: www.rotorflight.org/docs/Tuto...
0:00 Intro
0:39 Erasing the Nexus
1:49 Speedrun
16:20 Flight
@radiomasterrc - ยานยนต์และพาหนะ
THANK YOU, THANK YOU and THANK YOU Jonas for doing these vids!! Sure does take a LOT of the mystery out of the Nexus so anyone should be able to set one up!! 6 months from now these will be mainstream!! So far I LOVE mine in my M4!! Flies amazingly well!! I have 6 fligths on it so far and it's AWESOME!!
It was quick, but something to aspire too. Thanks again. Look forward to any more videos you produce. Bis Spaeter.
Thanks Johnny! Those PIDS works! My Heli is now more lock-in. Running mine with Futaba 16IZ. I follow those PIDS with caution 😂, I figured OMP M4 is somewhat close to the 420 Raw, and I’m not a newbie so I did them today and wow! I did your setup also with the M1 and love it, thank you so much! Regards from Cali!
Ricky
Thank you for your very helpful videos 👍🏻
Thank you Jonas
Your amazing with your skills, also useful info in setting up the Rotorfligh programe. 👏👏👏👏👏
Your first video was excellent at explaining the setup. I feel that I can follow it to setup my next model. I'm very curious/nervous about PID tuning and rates. Hopefully that will be covered in a later video. RotorFlight is the future.
Nice backyard!
I've been trying to tune my Goosky Venon on Flydragon for a couple of months now and kind of gave up due to not learning to how read and tune off the blackbox. Today I used this video as my guide and my Venom is flying freaking awesome! I have a Nexus coming and will install on a Logo 500...if that flys good I may have to say goodbye to my trusty Neo's :(. Thanks Jonas!
Glad this helps! Next I'd recommend you look into M4 MAX and M7 😉
@@Johnny31297 I've built 2 M4's and will be building an M7 for a good friend in a couple of weeks. I am tempted to buy an M7. Maybe when my NME takes a poop?
Bro, excellent work and keep doing these as often as you can. Not only your experience would increase, but people will learn from you and grow. Quick question, is the M4 the smallest OMP this will fit?
I only understand very little, but thanks for sharing.
@Jonas what is the high pitched tinning noise in all the M4 videos I watch, is that the belt hitting the tail boom wall?
Not sure what you mean, do you have a timestamp?
Jonas when your setting the roll rate you set 9 degrees. Is that the quickness of a roll.
The issue with rotor flight wasn’t that it was hard to set up it was when it didn’t work there was nothing to fall back on unless you popped up on discord. The discord has been amazing though nothing but incredible and willing people on there!
What version of firmware you recommend for the tx and the erls receiver That is better for the nexus ?
Do you recommend the M4 ESC GOV mode or the one on the NEXUS?
How do you switch from different profiles? Where is that done?
Do you have to ARM the helicopter with a switch before the motor runs?
great work. im new to helis, can you do a video for beginner with auto level?
Same same, map a switch to Angle Mode, flip the switch, done
When the compensation is not going in the right direction what do you do or how do you correct that.
See my previous video
Still a lot of terms to learn
A little off topic to your video, but how well does the M4 Max autorotate? Can't seem to find any videos showing this
It autorotates extremely well. I've done it in my videos before!
@@Johnny31297Danke from Canada
Мені трошки допомогло.
Я хочу подивиться відіо по налаштуваню передавача.
man i wish my tx16 speaker was that loud did you upgrade the stock one?
No, it's stock, but the MAX MKII has an upgraded speaker 👍
@@Johnny31297 same radio i have. wierd maybe il buy a new speaker and try it out. thank you
very good video. In the future please make videos explaining profiles pid gains and filter adjusts. Without the theory behind this things we cannot adjust for our models. Thanks a lot sir.
50% of that request would already be fulfilled if you go and read the annotation at 10:29 😉
I thought you didn't have time for anything !
That's why we're speedrunning!
Jonas when your setting the roll rate you set 9 degrees. Is that the quickness of a roll.
Jonas explains this a lot better in the precious setup video. But basically the override (where he sets 9°) isn't a setting at all. It's the same as a stick input but given through rotorflight. What you do here is calibrating rotorflight to rhe actual values on the Heli.
So basically you make sure that what the program sees as 9° (this could be 10, 7 or any value) is also what the heli outputs
@@RubenRC94 This is the correct answer.