Eps. 2.3 - Handrails Re-bed and Hatch Refinish S02EPS03
ฝัง
- เผยแพร่เมื่อ 5 ก.ย. 2024
- Time to fix a few things that didn't work out from last season. The hatch cover's finish didn't last at all under UV light from even just a few months exposed to the sun and the handrails needed to be re-bedded with a new ay of keeping them secured.
My Patreon Account if you'd like to donate:
/ thesalvationnavy
TotalBoat has given the viewers of this channel a special code for discounts on TotalBoat products. at Checkout, enter the promo code TBSalvation
Thixo Regular:
www.totalboat.c...
Thixo Extra Flexible
www.totalboat.c...
All Thixo Products
www.totalboat.c...
Cetol Natural Teak
www.jamestownd...
Cetol Marine Gloss
www.jamestownd...
I used dillute wood glue and wicked it up into the handrail gaps....after several times and if done after a rain the glue would wick its way up and now several years later the hand rails are still tight.
Absolutely a pleasure to watch your work. Love it.
Thank you! Glad you enjoy them.
Funny that your video showed up in my YT recommendations. I’m restoring a small yacht and I had a different solution for my handrailings: I inserted screw-in nuts in the bottom of the railings and secured them with stainless steel bolts with a large head from the inside of the roof. I used glazing sealant to prevent leakage.
Works great and they can be removed without causing any damage, as I did earlier today.
You will never be the rails off in the future without damaging them. The epoxy bond will rip out the wood. Further, it has no flex, so as you pull on the rails it will will pull the fibers out of the wood and leak. You need a flexible bedding compound to avoid that issue.
I used dillute wood glue and wicked it up into the handrail gaps....after several times and if done after a rain the glue would wick its way up and now several years later the hand rails are still tight. I wonder why anyone wood remove them?
@@rodpaget9796 you may have to remove them again if they begin to leak and they will because he used epoxy to bed them. Then because he used epoxy, he won’t be able to get them off easily. The recommended method for bedding deck hardware is to use a flexible, non-hardening compound like 3M 4000 or butile tape. They’re both flexible, non-hardening, that will ensure removal in the future because they will leak again, no matter what you use.
Good video and appreciate the effort you put into these.
using Epoxy is one way to do it, but maybe would have not been my first choice only because you will never get your handrails (which are very nice and seem like a unique design) off again without damaging them. You call Thixo a 2:1 epoxy adhesive "sealant" but it technically isn't a sealant unless you use it like you did and any flexing might break that seal.
Thru-bolting your handrails were the key to making them sturdy.
Using thicken epoxy to fill your core area is good, but I prefer to use the bent nail method to allow the fiberglass skin to remain on the top and bottom of the hole. Takes a bit longer to achieve good results though.
I probably would have stayed with Bed-It Butyl tape after filling the core and drilling your holes since the through bolts are doing the work here. When using Butyl it is important that you chamfer the edges of the hole, and wrap some around the bolt before you insert it into the deck. (BTW - my handrails have the nut in the handrail and the head of the bolt down below.
I have had mixed results with plug cutters. I have found that I often need to sand the plugs a bit to get them to fit properly.
I have been debating on varnishing the hand rails since there are just too many nooks and crannies you might might get failure from. Cetol or Semco teak sealer are good options. I have used Total Boat's Danish Sealer (like Semco) with Sunbrella covers over my rails with some success this year. The Danish teak sealer won't last all year if left exposed and it is a pain to reapply if you need tape everything first - just like Cetol or Varnish...
Hi Neal. I too consider it important to be able to reverse the install later on. I'm going simpler even with screws only from the bottom, just like Tanzer did in the first place (which already lasted 43 years). I'll be filling the gaps and holes with butyl tape. What works for some might not work for others based on their circumstances. Thanks for sharing!
How will you or anyone in the future get those handrails off? Aren't the screws now expoxied into the hull?
I don't plan on taking them off. The bolts can come out easily enough from the hull as metal won't bind to stainless steel. But the wood rails would likely be ruined. But that's the only condition I'd tale them off is if they were damaged beyond repair anyway. Was way more important to me that they be 100% secure and safe to use AND not so loose that they allowed water into the decking, which would cause even more damage.
We need to send you some Marine Wood Finish - better than Cetol!
TotalBoat I’d be happy to try it out. I really like how Cetol natural team makes the team look, but it doesn’t look great on other woods and Cetol just doesn’t hold up well to mechanical contact. Love Halcyon for what i have used it for so far.
I'm located in Ottawa, canada, and would love to try out some of the TotalBoat products. Are there any distributors up here?
@@jackrabbit5047, unfortunately, we do not have any distributors located in Canada