I had ‘error 15’ showing, done what you did in the video, and it’s cleared it. Those wires was stuffed/crammed into a grey rubber cup with some right angle bends to them.So I took them out of that grey cup and tape each connector, and free those wires so the do not have such a bend on them, THANKS MATE 👍🏾🇬🇧
If it didn't solve the problem, try disconnecting all the 3 wires, and connect them back. Error 14 worked that way for me. Anyways thanks for the video, helped out! Appreciated man!
Thanks this fixed it for me. In my case, I had to first remove the cables from a rubber pouch. Then I just pressed the connectors for my together. The error code went away.
In case ^ this ^ doesn't work for someone: what fixed it for me was taking apart the break handle, cleaning the sensor and wiring, taping the sensor in place and putting it back together very firmly.
Kudos to this video: I've watched all the other Error 14 videos, including the ones that agonizingly walk beginning-to-end through dismantling and trying to reassemble the Hall Effect Sensor. This video should be the FIRST step: just like looking to see if a dead appliance is really plugged in before you start tearing it apart searching for a problem. Twice now I found - and I don't quite understand why - that the little white wiring harness under the dashboard rather than the dozen moving parts in the throttle is the problem. Checking this is infinitely faster (as is buying a new throttle on Amazon rather than jiggering with the old one should it happen that the throttle Hall Effect sensor really has failed). Tools-wise you need a very small O2 T bit as well as a jeweler's Phillips head and tiny scissors to cut the wire tie on the rubber boot holding the cables, plus electric tape and a new cable tie. Do it with some light as the fasteners are all very small.
I did this and it cleared the error code but didn’t fix the problem, I still have no drive to the throttle. I didn’t take all the wires out of the rubber boot and tape them individually, will that help?
There is a decrease in the speed, the speed was 25 km before, and now the speed has become 22 km in the fast sports mode, how can I restore the speed as it was in the first 25 km
This happened to me on my brand new Max. Getting a replacement but recommend putting some electrical silicon on the Hall effect transistor (surface mount component) and let it dry for a few hours before you re install. NOTE: The silicon should not interfere with the Hall effect transistor sensing the magnet but to be safe I would silicon all around the component and the 3 leads that are soldered to the board and keep the silicon off the top/face of the component. This will ensure vibrations don't cause the same problem again..
What is if this not fix the code 14? I have code 14 since a few days and no chance to fix it. Please help. I have new throttle and it still dont help :( Maybe new dashboard?
The tool/screw-driver is called "Torx Key " but make sure it is one with a divot/ hollow in the center, you probably can purchase a set of these on AliExpress
Also I believe the size is #14 but I might be mistaken, so you are better off just purchasing a set of these just to be safe, they are fairly inexpensive on AliExpress. FYI
@Beta no,you dont need too,you can just replace the controller board [box] it cab be found on ali express for 40 euro,you get the controller,display and cover for that price or less,hope that helps people in the chat
Mine keeps doing error 14 after I fix it lasts 1 week then does error 14 again ..... why does it happen at all ... where is main problem occurring from
This video literally saved me 200$ THANK YOU SO MUCH !!!! It solved my error 15 problem
Thanks, fixed error 14 easily
I had ‘error 15’ showing, done what you did in the video, and it’s cleared it. Those wires was stuffed/crammed into a grey rubber cup with some right angle bends to them.So I took them out of that grey cup and tape each connector, and free those wires so the do not have such a bend on them, THANKS MATE 👍🏾🇬🇧
If it didn't solve the problem, try disconnecting all the 3 wires, and connect them back. Error 14 worked that way for me.
Anyways thanks for the video, helped out! Appreciated man!
Buenas, Esté modo serviría para un eléctrico - Segway-Ninebot MAX G2 E ?
Thanks this fixed it for me. In my case, I had to first remove the cables from a rubber pouch. Then I just pressed the connectors for my together. The error code went away.
Thank you fixed my E4 - did the same thing, disconnect and reconnected the wires and it worked! Definitely a good trick to know!
Thanks, when it was beeping I disconnected the connector with a green cable, connected it back and it worked.
Thankyousomuch man.... I just fixed mine following your video... God bless you Sir🙏
Mine is doing the same thing but I’m getting nothing but a beeping sound but no display and I checked the wires but nothing pls help
Thank you so much. I just finished fixing my son's friends scooter. 😆
In case ^ this ^ doesn't work for someone: what fixed it for me was taking apart the break handle, cleaning the sensor and wiring, taping the sensor in place and putting it back together very firmly.
Will this help for code 14 also?
@@gurkenhals2795 I doubt it, unfortunately. That's a different sensor I never had to look into.
How did you clean the sensor?
I want to give this a shot after trying everything already
My screen will come on wen the handle bars r down wen I click it back up all power from screen nocks of any idears wude be great thanks
What happen if I don’t fix it?
Kudos to this video: I've watched all the other Error 14 videos, including the ones that agonizingly walk beginning-to-end through dismantling and trying to reassemble the Hall Effect Sensor. This video should be the FIRST step: just like looking to see if a dead appliance is really plugged in before you start tearing it apart searching for a problem. Twice now I found - and I don't quite understand why - that the little white wiring harness under the dashboard rather than the dozen moving parts in the throttle is the problem. Checking this is infinitely faster (as is buying a new throttle on Amazon rather than jiggering with the old one should it happen that the throttle Hall Effect sensor really has failed). Tools-wise you need a very small O2 T bit as well as a jeweler's Phillips head and tiny scissors to cut the wire tie on the rubber boot holding the cables, plus electric tape and a new cable tie. Do it with some light as the fasteners are all very small.
Thanks, this fix my ninebot scooter 🛴💪🏽 at the moment 😂
When disconnecting the wires does the scooter have to be on or off ?
Thanks to you First canary wharf.
Which size of Torx did you use to remove first panel?
T10H
Thanks VERY much - fixed the Error Code 14!!
Thanks. Fixed my error code 14
I did this and it cleared the error code but didn’t fix the problem, I still have no drive to the throttle. I didn’t take all the wires out of the rubber boot and tape them individually, will that help?
Thank you for the great video. I’ll save this one, and subscribed!
worked for my 13 error! tnx
Yeah but what causes it in the first place?
the screws don’t come out of the thing and are super tightened sprayed it with wd40 and stuff
Comentario es español: si funciona, supongo que por las vibraciones esas conexiones se sueltan, es ajustarlas fuerte y ya
Cool vid thanks for making and posting 👍
Dude, LIKE A BOSS! Thanks!
Hi I have my sons scooter it will turn on wen disconnect battery but wen I go to put handle bars up the screen goes blank any ideas
The problem is really solved. Thanx 👍
There is a decrease in the speed, the speed was 25 km before, and now the speed has become 22 km in the fast sports mode, how can I restore the speed as it was in the first 25 km
Thanks bro helped alot
Disconnected the throttle cable and reconnected it, did not fix error 14....
This method can fix most cases of the error 14 &15, but if you cannot fix it please replace a new throttle.
thanks for the help.
i really hope that will work when i needed. otherwise i will destroy max. no other option there....
Mine won't power on is there a reset button anywhere on these
What could happen if I don’t fix it?
Where can I find the tool that you used?
Anywhere. They are common tools. Buy a screwdriver set with wide range of replaceable heads and it will have what you need for years to come.
Will this be the same for xiaomi365?
OK, I'm going in, I'll report back if it worked for me, error code 14.
Man i cant find my scooters display screws
Cela ne fonctionne pas sur ma trottinette ninebot g30 car le code erreur est 15 ! Ce qui veut dire que c'est le frein qui est défectueux ( capteur )
Can u show how to speed hack or downgrade using st link
Tank you vrés gooood
Thank you so much
Thanks
What is Error 16? And, how do you fix that?
thanks
Yes ! Thanks ! 🤩
Big thx!!!
I had error 15 and had to replace the full break. A surface mount component broke of (for some reason) on the break sensor.
This happened to me on my brand new Max. Getting a replacement but recommend putting some electrical silicon on the Hall effect transistor (surface mount component) and let it dry for a few hours before you re install. NOTE: The silicon should not interfere with the Hall effect transistor sensing the magnet but to be safe I would silicon all around the component and the 3 leads that are soldered to the board and keep the silicon off the top/face of the component. This will ensure vibrations don't cause the same problem again..
@@AluzionTV think I commented on your post earlier on, on Facebook. Ninebot segway max group. Jason ? Aha
@@LeeHutch89 Yes
@@LeeHutch89 Safe to say since you replaced the brake lever no more issues?
@@AluzionTV yeah all been good since 👍🏻 was an easy enough fix.
will it work on ninebot e22e?
Thanks I fix mi scooters too
What is if this not fix the code 14? I have code 14 since a few days and no chance to fix it. Please help. I have new throttle and it still dont help :( Maybe new dashboard?
Solve or no?
Any idea how to fix error 22 in xiaomi e365
Can you drive with this error,i am safe while i am driving?
No. When I had this error the throttle stopped working.
What special tool is that?
The tool/screw-driver is called "Torx Key " but make sure it is one with a divot/ hollow in the center, you probably can purchase a set of these on AliExpress
Also I believe the size is #14 but I might be mistaken, so you are better off just purchasing a set of these just to be safe, they are fairly inexpensive on AliExpress. FYI
Size 10
Ive got my Ninebot G30 few days ago and when im driving i have noticed weird buzz from throttle randomly. Anyone had similar issue?
Mine does that too i think its normal
Do you have a fix for error 10?
@Beta no,you dont need too,you can just replace the controller board [box] it cab be found on ali express for 40 euro,you get the controller,display and cover for that price or less,hope that helps people in the chat
Hilft das auch bei error 10 ?
Wats error code 16
I can just find some screws beneath them
i have eror 18 pls
Where to get that kind of screw driver?
amazon
In any local shop, ask for torx keys.
@@Weisior what size?
mine is 18 pls help
It aint gonna help for long.. Changed couple of them.
Worked for me ... so far ... fingers crossed
@@69cinders is still working good ?
Why are people so afraid to talk
Mine still Beep
ninebot error 10 fix
Du lügst
This is Fake
Mine keeps doing error 14 after I fix it lasts 1 week then does error 14 again ..... why does it happen at all ... where is main problem occurring from
I had this issue too, I have reset factory defaults and it stopped doing it.