Ford Focus Engine Mount Vibration Repair
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2024
- Only buy Ford Engine Mounts you can get them Here- (check part fitment guide)
www.amazon.com/...
This is the Blue Loctite I use in the video-
www.amazon.com/...
Here is the safe and proper way to change out that engine mount including how to test for a bad mount! Torques specs are for 2009 2.0l Duratec Engine yours may vary slightly but these specs can be safely used on any model year.
Just replaced the engine mount on my wife's car. There is no way you can go wrong by following this video. You even gave us the torque specs and everything! THANK YOU for this!!
Unler the nuts inside the chassi snaps out and rotate with the bolt!😅😅
Finally got around to changing the passenger side mount.. and the difference is like night and day! My focus feels like it's literally gliding when it drives, it's soo smooth. I had to watch this video again today to gain the confidence to do the job and it took me about 45 minutes. Thanks again for the informative video!
+DaPaRappa I've been thinking about doing mine, but I don't feel too good about putting a jack under my oil pan. So, it wasn't too bad then?
psychotogen1 Yeah it wasn't bad at all. Just make sure you have a nice sized block of wood to put on the jack under the engine oil pan. I jacked it up slowly because I was scared, but it does spread the weight out making it easier to lift the engine.
DaPaRappa i finna do it soon scared tho
Young Reese Good luck
Young Reese P
Thank you very much! I just replaced the passenger side motor mount on my wife's 2010 Focus at 86k miles like the one you replaced in this video and the difference is incredible!!! She literally asked me "did my car start?" when she turned the key because literally 90% of all the vibration was GONE! $132.xx plus tax at my local ford dealership but it was worth every penny! I replaced it myself by the way in just a little over 15 minutes...
Thank you so much for all the details, your tutorial made this quick and easy. Best part is that the dash, the doors, and the window posts are silent now, and can look at the rear inside view mirrors, and they are vibration free! Thrilled with the results!
did your viberation smooth out at HIGH SPEEDS??? or was it constant always there with this mount being bad? my viberations ''go away'' at 73 plus.... eh... lol
Thank you very much, just did my 2010 Focus yesterday and it is so smooth now!!!. Wouldn't have done it without your video. Thanks. Cheers.
DAMN!! Like a brand new car now!
Mine looked in great condition but decided to change it out since I was going to tackle the alternator.
Was thinking of turfing this winter beater but gonna keep her now. Great vid man!
just finished replacement motor mount install. Worked to spec.....lock tite.....correct torques...bolts cleaned on wire wheel...jacked with buffer board. All went exactly as you instructed. Replacement mount was Motor Craft. Very quiet engine now. Thanks for your help. mike
Thank you very much for this great video. I just finished replacing the engine mount on my 2009 Ford Focus SEL and I was amazed at the difference it made. I am a very mechanically sound individual and the entire repair only took me 25 minutes. I was able to find the engine mount cheapest at AutoNation Ford Parts in White Bear, MN. I ordered it on 11/17/15 and it arrived on 11/19/15. Thanks again for all the great FORD videos. THE BEST NEVER REST!!!
I’m from mn too Pequot lakes area
Good job good to see someone clean the parts prior to assembly and using a torque wrench to avoid damage and making it easier for the next person.Thanks for the video we need more mechanics like you.
Thanks!
@@FordTechMakuloco You're AWESOME!! LOVE your videos!! My mom has a 2011 Focus SE. Always doing the work on it when it needs it. She has the same problem. I am pretty sure it's the motor mount. If it is, should the driver's side mount be changed too? I am just thinking about changing things in pairs like suspension parts. Thanks in advance...👍😁
UPDATE ...The mount(s) seem fine. I think it's her muffler. It did have a few small leaks on it on one end of it. I patched them up but a s***load of water came out of it. I think it's shot inside. Rusted from inside out. Should I buy an OEM muffler from Ford or are the aftermarket ones just as good? Thanks in advance....👍😁
Thank you so much for the great video. Bought the part and installed in under 30 minutes. My elderly mother in law had grown so used to the vibration that she didn't notice a problem. She certainly noticed the improvement after the repair. Thank you again!!!!
You made this look so easy. I have a 2010 Focus with only 55k miles and the vibration is terrible. I'll be doing this soon.
Did you do it yet?
Thank you for listing the torque amounts. Mine was rattling so bad it cracked the windshield. The mount was disintegrated into two separate pieces. WOW WHAT A DIFFERENCE! Simple job! A note of difference from all the other videos I have seen, including yours.....My passenger motor mount stand did not have a 6th bolt underneath. Mine was removed by removing a metal subpost(like Tom Crawford below).
Altogether, A simple procedure, and it runs so quietly now! I got my replacement piece for $20 bucks from a parts wholesaler(I never pay retail). Thanks man!
I dreaded the day I'd have to do this because I'm so scared of putting a jack under my engine to lift it. But it does look like an easy job. I'll be doing mine this Sunday. The only thing that differs in this video is my coolant reservoir has to be moved aside since the overflow and coolant tank is all one unit in the 2005. Engine mount is exactly the same from what I've seen. I'll be so happy once that vibration is gone.
Used your video to replace on my 2007 ford focus 4 door with 184k miles. Made it a 20 minute job from start to finish. Thanks!!!
Great video. Before I found this video, I was thinking of doing the test that you did, but i didnt know if it would work, now, watching your video, gives me confidence that I will know for sure if my mounts are bad. Thanks.
After watching sev vids each time I repair 1 of my Ford's i always seem back at your videos. Kudos to you!, everything worked out exactly as you indicated. My grandfather Head Mechanic over 2 international trucking lines as well Ford, Dodge, & GM
Did this replacement today and OMG! what a difference. I replaced the driver side mount first thinking it was the culprit. But even after that, when I would open the two back doors both of them shook violently! along with the steering wheel, and everything else in the cabin. Even the battery shook after the driver side mount was replaced. So I was confused as to how it could be the passenger side since the battery was directly over the other mount! But, NOPE, I replaced this passenger side mount and It took "ALL" the shaking away. The car shifts better too! Man what a difference. Best 100 bucks I ever spent! (Not really, But its up there!) Thank you for the informative video. I hope this brings sanity to anyone looking to solve this issue.
BTW, The initial test you recommended by slightly lifting the engine to relieve pressure on the mount was my green light that is was probably that passenger mount!!
Happy Holidays.
I've been trying to change my idle pulley and figured I didn't have clearance due to the bad mount. This confirms it and I'll have even more room and confidence to change two parts in one go. Much appreciation!!
I used a paint pen because a little brake clean and it come off, but a sharpie marker will do also. The anti roll mount is underneath center backside of the engine, mounts by where the trans and engine meet looks like a figure 8. Rocks get stuck behind it where it mounts to subframe. I would check this out first as it happens primarily in reverse when the engine torque loads the mount rearward. Search for tsb 8-5-6
Got the mount from Oreilly. It looks a little different. The brackets are a bit different on bottom even though the holes are an exact fit. I actually had to file a little off the bracket closest to valve cover it was almost top snug making the studs too angled. Just fyi if you get the oreilly one. $112. Great vid runs a whole lot smoother once installed
Fantastic Video - thank you very much for this fine guidance !
Today I changed this mount on my Ford C-MAX, 1,8 petrol, Trend from 2004. I have been driving with vibration issues for more than 3 years. My Ford service changed the button mount for about 1 year ago, but no big difference. Today I therefore changed the upper right mount myself. I used a Febi Bilstein mount, Germany quality, WHAT A DIFFERENCE - I HAVE A NEW CAR NOW, allmost. All vibration problems are gone now, it´s absolutely fantastic, I have forgotten how much comfort the car had before. There was no visual defects on the old mount, but I can se a small difference after mounting. The engine is about an half centimeter higher in the right side now, so the old mount just lost its strength over time.
All the best from a happy dane ...
Thanks for the video showing diagnosis. Worked perfectly and was able to fix the terrible vibration quick and easy!!
Thanks for the torque specs. 20-minute Job, and done much better
Thank you for this! I feel like I'm driving a brand new car after replacing the motor mount!
+AlmostADr2016 Yeah it makes a huge difference.
Great video. I think you may have helped me diagnose my U.S spec 2010 Transit Connect van with the Focus engine and mounts. Van only has about 36k and the problem started a while back. Vibration is noticeable at all times. Most noticeable through the gas pedal. Tried jacking the engine up and the vibration went away. Hopefully it's the passenger side mount. I'm hoping Ford will pick up the tab as I complained about the vibration and have it in writing well before the warranty was up.
the detail lifting the jack to take the weight was #boss ..great stuff
Just ordered my right engine mount F.focus 2005. Can't wait to drive in for routine inspection after I perform your expert procedure. They expect $300 bucks for the install....when I will have already done it. LOL. Next will be rear drum break overhaul. Thanks for your great series.
I just kept putting up with the rattling and noise getting louder and louder, but it was getting out of hand. I inspected the mount and it appeared that the oil had come out and it was worn badly, so I decided to replace it. Like other users have stated, it is staggering the difference this makes. Its so quiet I cant hear it now, and its very smooth as well. Great instructions, save yourself a few hundred dollars and do this job yourself.
I was told to get the part from the ford dealership though, they said the aftermarket parts wont be near as good and you definitely want to stay away from the 'solid rubber' ones.
Yup the aftermarket units don't last near as long.
I used all the steps you described and successfully changed my motor mount today. Thank you for posting this and God Bless!!
@Mardy Crue. I have the same vehicle as you, and when I was test driving it from the dealership I purchased it from, it had the exact same issues as yours. The problem was this side engine mount was leaking fluid. I made them replace all the mounts with OEM before I made the deal and it fixed the issue. Unfortunately, OEM is the only way to go for that particular engine mount because it contains fluid and the aftermarket ones are cheaply made and don't have the required fluid if any at all.
Is it reasonable to say that the engine mount fails due to fluid leakage? So, if the mount doesn't leak, then it should remain in good order?
So I went out and bought this part made in USA for $180 CAD, did the change thanks to your instructions, and the results are great. Huge reduction in annoying vibrations, but I still feel a small vibration and I think it's coming from the Transmission Insulator mount under the battery box. When taking the tranny mount out, where should i support with hydraulic jack. engine or transmission. Quite sure shop manual still shows the support beam over the engine area, but vertically.
+Washington Redskin Support the trans case the same way you supported the engine while the mount is out.
Thanks man, just fixed my son's 2017 in about 20 minutes. Easy fix and a big difference
Just bought an 09 SE same color! Actually has a brandy new motor mount from the dealer (left the genuine Ford Part sticker on) pretty happy got it cheap with 115k and a book of service records from the dealer!
I just got a second opinion Saturday and yes my passenger side engine mount does need replaced. Luckily the place that gave me the second opinion only charges $156 plus tax according to the invoice and the first place that mentioned it wanted $250. So I do plan to get it done at the place I got the second opinion from.
Yup very common.
MrWill1985 I would be curious what type of motor mount they will use. rockauto.com is selling anchor motor mounts for 7 bucks a piece, motorcraft motor mounts are cost anywhere from $85-100 a piece.
Thanks! This worked for us. The test with the jack and then the repair. We did it in about 30 minutes. BIG difference in the vibrations heard and felt.
done - the hardest part was putting the new one back in .... thanks !! Car is much smoother now ....
Thanks for your info....I replaced all 3 mounts. It was the bottom mount from the engine cradle to the tranny that made the biggest difference.
THIS VIDEO DESERVES A REWARD 🎉❤
Thanks for posting. Will be doing it soon. Used your other vid for valve cover gasket repair yesterday. Thanks again
Thank you for posting this video bro. This is going to make fixing my daughter's car so much easier to see it being done in real time. You're awesome!
Thanks for the video, got the job done. My replacement part from O'riely was only the insert, had to pry old one out and then bend a tab to keep the new one in. Didn't realize going in the lift point on oil pan was critical to getting a good lift. If too far to the center it lifts entire car.
If you lift too high it will lift the car yes.
FordTechMakuloco I had loosened the motor side nuts and the motor was lowering even though had jack under it but too far to the tranny side of the motor.
had my son in the car while i jacked up the engine like you said to see if it was bad...jacked a couple times and it got smooth as heck...so i did what you said to replace...it went great...put it back together but it still has a vibe...is there another mount that can go bad? they said at the parts store that this was the mount for the right side...so can i assume theres a left...i felt like a real mechanic for a little while...your spot on on the directions
Hi,
You've helped me in the past. I had a 2000 focus that went through three coils. You told me me about a potential wire grounding, and you were 100% right. Two strands of wire were left and were grounding on egr tube. Thanks!
My question is about your parts link on this video. When I click it, it brings up is a dea mount. When I look on a Ford parts site, the price is significantly different.
Should I purchase part from dealer? If not, should I stick to dea manufacture only? In the past, I have had the best luck with dealer parts, but they are just so much more costly.
Thanks in advance for your great advice, experience, and insights.
Dude thanks couldn't find a video like this anywhere
Holy crap this channel is such a lifesaver
just got one used for 3k 120k miles with this paint and part its like new thanks allot man
Thank you again! solved the problem with my 2011. With 80000 miles on it. I was surprised that it when bad so soon. My sons lasted till 150,000.
Thanks your video was spot on. serious vibration at idle, shifting to reverse or drive. Got a new mount at Napa, smooth as silk now! Thanks
hey, I just had this done today on my Ford Focus, cost 107 bucks, but it took them 2 hours where you did it in about 15 minutes
Purposely took 2 hours I'm sure
" You are I am" was playing in the background :)
Great video, explained it very well. Bought a zx4 with a bad passenger side mount. I feel perfectly capable now. Thank you.
Ten Years later! Thanks a bunch Fr Thank You
Thanks for the instructions. Just changed the passenger side mount on my 2013 and now it drives like a new car....aside from the transmission which Ford never seems to get working right. Still has that shudder in low gears.
Never seen the other side which is the trans mount go bad like the right hand side engine mount in this video. Go ahead and check it like I show in my video. Other thing to check is the rear anti roll mount under the car for rocks causing the vibration when the engine is loaded a certain direction.
yes unbolt anti roll mount and check the cavity for rocks and debri grounding it out.
Not sure which bolts you are referring to but I am sure they are supposed to be there. Yes you can use ramps in the rear but make sure its in park AND parking brake is on as they are natural free rollers back there.
Good job demo straighting and explaining.
The best ford guy in TH-cam 👍👍👍
Torque Specs:
2 Engine 18mm Bolts - 66 ft-lbs
3 body 15mm Bolts - 35 ft-lbs
I just did it myself, jacking up the engine right was the tricky part for me
Excellent video, and thanks to this I will change my own. However the link to Amazon for the part seems to be in error. Got mine ordered from eBay. Oddly enough I'm kind of excited to work on my car.
How long are the originals expected to last in terms on miles traveled? And are the aftermarket replacement ones likely to last longer? And finally, is it just the right hand engine mount that is a problem, or should I be replacing any other mounts as well as the one shown in the video?
I used your video to fix the mount on my transit connect, very detailed and was easy to do. Thank you for making this!
I have the same problem on my transit, u did all the mounts or just the left side ? Thxs
Oswaldo Ceron sanabria I just did the left side. Haven’t had a problem since I changed it out.
Thanks I’m gonna replace it this weekend. I hopefully I solve the problem.
Thanks for the video. Worked like a charm and saved me at least $200
best video on this subject ive seen.
I have the rough idle and vibration. Mechanic have me an estimate and told me it was the wishbone mount. He rocked the wheels and the whole thing shook. I’m guessing all three need to go, but I will start with that one and then these if it doesn’t fix it.
I have never had an issue removing the bolts for the anti roll. A little rust penetrant is advisable of course no matter what. Yes where are the pictures located
You must use a FORD OEM Mount. Believe me a knockoff will not work. I’ve tried. I finally shelled out the dough and the car is so quiet. It’s amazing.
I'm not the least bit scared of work, I can sit on my couch and watch someone else do it on TH-cam ALL day long. LOL
Remove both bolt pull mount and check out the cavity it sat in the subframe. No engine support needed may roll a inch or so but that's it.
I really enjoy your videos and the work you do, you are very informative and helpful !!! With that said, I absolutely don't like the way you use your influence to make people believe that they should only buy oem products, there are many after market products that are just as good and even better than the original Ford parts !!! there are many after market products that are inferior and perhaps that's why you recommend them but OEM isn't the only solution !!! With proper research you can differentiate between the two !!!
If there is an aftermarket product I would certainly suggest it, Have you seen all the videos on the Melling brand oil pumps? In this case and most other cases nothing but OEM should be used this is the voice of experience not personal preference.
I'm impressed with the one handed repair job! hope to do this this weekend!
as long as the plate that touches the pan is wide like a block of wood to span the load out then its ok.
The Ford engineers that designed the mounts on this car shouldn't be allowed to design a lawnmower. I have replaced the passenger side twice now on an 07 2.0L and the car doesn't even have 100k yet. My Corolla has 220k and have never even had to think about the motor mounts.
I had a slight vibration on the car for 8 years. I always thought it was the wheels. After replacing replacing the engine mounting when started leaking 3 days ago the vibration is gone. My car is driving like a brand new car
Great video! I have a 2015 Focus 2.0 with the infamous DCT and it shakes at lower speeds, especially going up hills. Could this be caused by bad motor mounts? The car has 60k miles on it but it's a northern car.
"The torque spec on these is 66 foot pounds" -immediately uses 500 foot pound impact wrench to tighten the bolts. That was hilarious 😂
It’s all in the feel
i am sure u save lot of people from rip ...u the best...
thank you for this video I really wish you would have did it aerial view of the components under the hood while the wood was in place because I couldn't see it. you may have tried but the wood was not visible when u panned back. I was only able to see the wood when u showed a close up but I would like to see it from far back so I can get an overall full view
Thank you very much for de video. My Ford Cmax has the same problem, and now i can do it myself!!
Thanks, from Spain.
Wonder if this is a good time to replace accessory belt?
I was thinking the same thing 🙂
Here is some great advise from an FF 5 time owner. When replacing the right MM, do nor scrimp out on quality. Buy a Motorcraft part, not the cheap knock offs. Mostly made by Anchor, China made junk. The Anchor will work fine for 7,000 miles then vibrations will return. Save yourself the extra time of replacing the mount a second time. JMO.
Thanks for that
Getting ready to do mine. Easiest check to see if it's bad...put a finger on the mount's rubber! You'll know real quick
Hi, I've got a question. My passenger engine mount is blown on my MK3 focus (it's leaking) and it's been a couple of months now. I don't get too strong vibration from the engine, but I get some shudder when taking off in 1st gear, but only when the car is hot. Do you think there might be a link there? Thanks for your video.
Great video I'm going to try this my damn focus has 59,000 on it and it's a 2001 it was given to me by my grandma but anyways it shakes when I put it in drive and in park it's not that bad
2010 Fusion I spent all year trying to figure out what I thought was an exhaust leak, hope this will fix it
i just bought my focus recently and the shaking started while waiting at a traffic light also my engine management sign has appeared - I have a 55reg 1.6 zetec
Thank you for this video. Very informative and easy to follow.
thank you for help..car is good now..however, I was too afraid to put 66 ft lbs torque as I felt like I was going to break and lose threading. Will it break? 66 ft lbs is a bit too much. I was turning the torque wrench and still couldnt hear the click . I stopped tightening afraid I was gonna snap it
Any chance you could elaborate on the “power train/drivetrain mount neutralizing”. Loosen the power train/drivetrain mount fasteners, would that be all the fasteners holding mounts to frame?
I'm hoping this is the issue with my girlfriends 2014 Focus. Bought it brand new and besides the transmission issue most people are complaining about, (we have that too) The vibrations in the car are like nothing I've ever experienced before. You can drive down the street at 20mph and it sounds like you're driving a tank! We literally don't leave change in the car because it rattles so bad. Road trips are almost unbearable because you can't hear each other over the sounds in the car. I just found it hard to believe the motor mounts would be bad after 2 years but after seeing this it's possible. Thanks for the vid.
Just got my new mount today. Thank you for the video.
What happens if you're cover plate bolt broke completely out of the thread on bracket to engine?
I replaced the hydraulic mount and it got rid of 75% of my vibration issue. I then did the roll restrictor and it was 90% better and got rid of a nasty clunk, then I Changed the belt and that about killed the vibration
What is the roll restrictor ?
I think he's referring to the lower rear engine mount that has a TSB for adding a shield kit to a replacement mount to prevent road debris from getting at it and destroying it.
Just repaired my 2010 Focus SES Coupe mount this afternoon. After 187,000 miles put on as the original owner, it was time. It's like a brand new car. Don't save a few bucks; go to the Dealer Parts Counter and get a OEM one. Another thing I'd suggest is taking the one 10 mm bolt out of the Windshield Wiper Fluid neck so you can CAREFULLY flex it as you pull the old one out.
I have a 2011 Ford Fusion with just under 49,000 miles on it. I brought it into Ford service 2 weeks ago when I notice the steering wheel started shaking and the engine sounding like it was racing, and a lot of cracking/squeaking sounds coming from what sounded like the engine. after keeping the car for three days they said they couldn't duplicate the issue I described and told me the suspension/alignment etc basically everything checked out. After a week of having my car back, I was still experiencing the same symptoms, I just dropped it off again yesterday and Kevin my service advisor called and said that they needed to replace the engine and transmission mounts. My question is this, My car has never been in an accident, Is this normal for a 2011 Ford fusion with just 48K+ miles to have both engine and transmission mounts go bad?Thanks for any advice :)P.S. I also notice a funny odor coming from the heater since everything started happening.
+Rebecca Janke I have seen the right hand mount separate and cause vibration issues yes but yours being so new and of such low mileage I highly doubt it. Is this the 2.5L? At any rate I think they are throwing parts at it at this point only have them replace the right hand mount and be sure to inspect the condition of the lower dogbone mount for wear and or debri grounding it out.
mine is manual transmition, Are the same auto and manual mounts? thank you great video
can you do a video on changing the mount on the drivers side 2013 focus st
I saw a video for that one it's underneath the battery box it looks extremely simple to do and remove just make sure you lightly support the transmission just like what he did with the oil pan
I was *FINISHED* with my '07 Focus...the vibration got so bad. I figured the engine was aging and vibration was inevitable. I swapped out all the mounts and wow - the car drives like it's new again.
tanbrolo how many mounts did you replace?
Maria Tejada I replaced all three. Apparently the most common trouble mount is the top passenger side. For me, I found that changing the bottom mount made the most difference.
I had Autozone run the parts. They show two passenger side mounts for the 2007 Ford Focus. One called Front Passenger Side Mount and the other Rear Passenger Side Mount. There is also a third mount on Driver's side on the bottom. You are referencing only one Passenger side Mount, AND I see only ONE on my car, and it looks like the one you changed.
Can you give a little more insight on this? Good video, by the way; most vids like this are not so good.
After removing the old mount, would this provide an opportunity to more easily replace the belt? I’m at 103,000 miles so I’m probably due for changing the belt as well. Thanks 👍🏻
Thanks for the video. I had the same issue on my 2004 focus zx5. I took it to the dealer and fixed it, it feels like new now. They also checked the brakes and found a damaged thread on the rear spindle. They suggested to replace both rear spindles down the road. Would you recommend buying OEM spindles? Or aftermarket ones are good enough?