ฝัง
- เผยแพร่เมื่อ 30 ก.ย. 2016
- How to open and read a EDC17C46, in this case it was from a AUDI A3 8PA 2000cc 16v TDi(CR) of 140hp.
There are several protocols for this ECU, some have Tprot some dont. Make sure you select the correct one. Ktag takes quite some time to ID the ECU but its normal so be patient!
Same procedure applies for KESS, just that you must read as BACKUP to get full info otherwise is just maps (like a OBD read).
Hope this is usefull and dont forget to Subscribe. - เกม
Great video!
I have grow up with old fassion mechanic tuning. But I has go with the time. So the lost 3 years I studing very hart on ECU Tuning, and thiss TH-cam Video helps me a latt!
this video is very good for new
person
thank you very much God will protect you
Good job!!!
Hey Thanks Buddy its work fine upload some more
Thanks for the video. Also nice nes keyboard
Hi
Can you help me with Mitsubishi pajero 2006 GDI ECU
couldn't you get this data from internet and use it to flash
Hi friend, do you know how to read a edc17 cp47 Bosch, is the one for the chevy Cruze 2014
Hi, which tool can do full clone EDC17C64
Its possible write with kess? A6 2014 ?
hi I need advice about a 2004 Honda Aquatrax with a code 25 Fault code
hi how much this program cost?plz
I have an 2006 audi a3 2.0t 8p. ..i just installed k04-023 turbo,flap delete.rs4 injectors and upgrade the hpfp...but i need it tuned...is any way u can help me?
Do you have the ecu file?
Hello. This is good 👍
Goog job
Thank you bro I am try p269 but your video is very help full I try p199 and work is done thank you ☺️
Is it can be write with this protocol
nice work
thanks, sorry ecu was a bit dirty! :D
Hi, if i'm sending my file to a tuner do i have to mail a full copy of the backup
just the file that has the maps!
hy ,do you use after remap new sealant ,or its ok with the remaining sealant ??
Yes you must use just in case , a tiny thin line of sealant!
Very Nice!
Boot mode not bench👍
Where's the power supply? In ktag when I read through 268 it says no power supply to the ECU.
Hey is this Ktag clone with red pcb? I have A6 4G with same ECU will i be able to Read/Write with Ktag clone Red PCB? Amazing video btw
Another great video!
What temperature you use when heated ecu?
hot air gun is set to 400 C , but i check with my hands to see how hot it is..
Lods, will show us Full tutorials ecu pinout old 2004 to 2005 24Volts Isuzu 4hl1-1, 4hk1. Delete Egr, dpd only
Is this a full read of ecu
not able to flash though OBD port ?must remove ECU and wire jummping cable?
it was long ago, now modern tools can do OBD or bench
How big are those files ?
And what do you need to rewrite only for the map? For egr off
mpc only for maps area. they are 2 mb
@@Automotivesp thank you mate
Can you write stuff to ecu this way ?I want to delete my immo I have a 06 tdi jetta bosch edc16
edc16 u need to do bdm read of eeprom for immo off. they also sell some OBD plugs taht do immo off via obd directly for your ecu
@@Automotivesp where to buy? thanks
cant you just use kess v2 on theese ecus?
Only for write
Ile się wgrywało kessem
Salut, daca sunt 2 pini de boot, trebuie sa te conectezi la amandoi sau poti doar la unul ?
amandoi impreuna
@@Automotivesp ok, mersi
@@Automotivesp Salut, uita-te te rog pe mail, ti am lasat ceva.
Hi, accord 2009, 2.2 idtec 147hp can be remapped using kess? Thx
da
@@Automotivesp mulțumesc. Atunci dau comandă de unul, cît mă va costa un remap la fîșier primul nivel și cu egr-ul și dpf-ul stins?
Am cumparat fisierul pe ebay, l-am incarcat pe ecu si mi-a aparut un puf cu semnul exclamarii pe bord. E dpf filtru, am inteles ca trebuie sa anulez masura de cenusa din el, asa mi-a spus vinzatorul. Am incercat cu delphi versiunea 2013 si nu se primeste. El se conecteaza iar cind dau anulare imi spune ca nu se poate conecta cu ecu. Cruizul nu-mi lucreaza, oare e normal? Poate fisierul mi l-au facut aiura. Masina merge foarte prost. Multumesc .
poate imi recomanzi pe cineva care face remapuri de calitate ca pe viitor sa am pe cine conta.
@@MihaiViteazulVoievod da tipic dpf off la opel nu mai merge cruise. trimite sa ti fac
3:29 What kind of oil did you use?
That is liquid FLUX by JBC brand!
hey people is the connection also possible without soldering? is that what the bmd stations are for?
NO, the bdm pads on ecu replace the wires on main connector. for boot and CNF u can use test probes
@@Automotivesp good info, thanks.what is test probes?
@@ondralohnisky like some long needles with a little spring inside to touch board points instead of soldering cable
Can you tell me the soundtrack please. Many thanks
Soundtrack i bought with legal licence from
JeeJuh.com - Light In The Disco - Produced by Elliot Waite
Brilliant, thank you :)
Спасибооооо)))
bonsoir j'aimerais savoir ce matériel il vaut combien pour reprogrammation des calculateurs et pour aussi supprimer des anti démarrage svp merci d'avance? ?
utiliser kess KTAG fgtech et d'autres, si j'annule immo
bonjour je cherche comment supprimer les anti-démarrage des calculateurs svp
Plz share music link .
music is property of jeehuh productions. i have bought legal licence!
yeahhh do you perhaps have another video where you explain as to what and how the hell you get it to work ?
get what to work? what is your problem i ll help u
@@Automotivesp so I bought the K-tag without slightest knowledge of how to use it and I still have not returned my TDI to stock :( simply because i dont know how to use it
@@Automotivesp problem is dealership put lock on ECU and the only way to get data from it is to use KTAG
@@BlondynCh password can be obtain and bypassed, this ecu is even doable via OBD perfectly with new original tools. if u have problems u can ship ecu to me
hi. i get micro protection removal failed with ktag , any clue? thanks
try same ecu but protocol without Tprot. if ecu has no tprot it will give micro error
@@Automotivesp i did now opposite choose with tprot and it worked, before i choose without tprot and got an error. Thanks Ominimicu
you dont need heat gun, i never use heat gun. good scalpel and gasket scraper and take your time.
Vandal
Maruti swift ecu
Vinod Verma th-cam.com/video/ZAPbJJ79MfA/w-d-xo.html
Plz share and subscribe my channel
Ktag clone it's or ori ktag
warning! stupid noise(music maybe) all over the video.
Ill tell you a little secret, you can turn off from your pc the volume. Every single man has different taste so dont be so smart. Hate those comments. Idiotism.
@@MihaiViteazulVoievod when you expect a dancing video, is normal to expect music. not really on electronic units.
@@zamirshehu9968 as i said everyone has different taste, do you know that some nations dancing and play happy music on funeral? Some even dance with the dead body. Oh yeah , he should of ask you what melody to play for his video. Id say he "will" next time. Im being sarcastic.
couldn't you get this data from internet and use it to flash
couldn't you get this data from internet and use it to flash