Hi Shemek. Great Video, I know that its been a while but I was wondering if you could help me out please, i have the Master version of Kess (Clone), which has not been reworked, so my first question is, Do I have to do anything to the Board on my Kess to make this work? Also I carried out the first procedure that you did in your video for Unlocking the ECU, however, When I connect it back to the car I am unable to read the ECU it comes up with a weird error saying, "Change of Status not Possible", have you ever heard this? If so how can I overcome this please. Also, in the second half of your video you attached a cable via a box that simulated the OBD being connected, where can I get hold of that box/cable please? Finally, if I were to have gotten that cable and box where would I see the relevant illustration to connect the appropriate wires to the pinouts Thank you in advance, looking forward to hearing from you. Mark
Hi great Video, question: on older ecu i have a 6digit Software number to find the correct tuningfile, but on edc 17 i can nothing find, can you give me a helping information? Thank you
Hi Shemek. Sorry to bother you again, but I have been looking through all of my Tuning Hardware and I have come across a OBD2 Bench Reading Cable, it has 7 Pinout Cables plus a Black Cable with a Croc Clip. Then there are two long Black & Red Cables with Croc Clips and there is a small Slider Switch, obviously to turn the box on and off, if you could provide an email address I could send you a photo of it, I was then wondering that if this item is OK you could let me know what wires goes on to what Pinouts please
Hey Shemek I had bought kess V2 clone from china Version 2.23. When i try to do pcr 2.1 on that, it says "Invalid Protocol File" Do you have any Idea, Why its saying That. BTW Great Video. Keep Up Regards From India
That so called "music" is UNBEARABLE!! PLEASE delete that awful racket, and put on something lower in tone and soothing; how about (1) you can do magic, by AMERICA. (2) cast your fate to the wind, by SOUNDS ORCHESTROL. 😎🙋
![THE TOYS x NONT TANONT - ดอกไม้ที่รอฝน (spring) [Official MV]](http://i.ytimg.com/vi/pPa1d5cC8M4/mqdefault.jpg)
Good video Man Thanks!
Hi THX for uploading, where did you get those Spring Test Probes?
Great Video mate! Please tell me, where i can get the boot mode to obd2 converter that you show in the video? Best Regards
kess clone 5.017 read flash on the bench?or ktag 7.020 gpt cable read flash ? thanks advanced
thats wonderful
Does it still need to be unlocked with kess 5.017 and ksuite 2.47 or it fully works trough obd? Thank you.
can it be used on a 150 cc motorcycle
Hi,
After the unlock, can you write on Ecu with the obd interface .
Parfait ! Merci
after unlock is full read write possible ( with same cable)?
Hi Shemek. Great Video, I know that its been a while but I was wondering if you could help me out please, i have the Master version of Kess (Clone), which has not been reworked, so my first question is, Do I have to do anything to the Board on my Kess to make this work? Also I carried out the first procedure that you did in your video for Unlocking the ECU, however, When I connect it back to the car I am unable to read the ECU it comes up with a weird error saying, "Change of Status not Possible", have you ever heard this? If so how can I overcome this please. Also, in the second half of your video you attached a cable via a box that simulated the OBD being connected, where can I get hold of that box/cable please? Finally, if I were to have gotten that cable and box where would I see the relevant illustration to connect the appropriate wires to the pinouts
Thank you in advance, looking forward to hearing from you. Mark
Hi from Spain. Fantastic video I have a doubt ... Once the process is over, the UCE should be blocked again, right? What would the procedure be like?
perfect!!!
thanks!
thanks ! great !!!!
Hi great Video, question: on older ecu i have a 6digit Software number to find the correct tuningfile, but on edc 17 i can nothing find, can you give me a helping information? Thank you
Nice song
Sheremek
Video min 06:17 what is the name of the apparatus?
or Wiring diagram send me ?
to read and write on the counter.
Thank you...
Czy da radę sklonować edc16c39 Opel? Jak tak prosze o kontakt.
anyone know if ktag and kess clone are any good at all? it worth it?
hi kess how much cost ?
Hey,
do you use a tricore adapter?
Yes.
why you play with kess. cant ktag do it?
hello friend , how to know ecu type without disengaged Ecu or seeing label ? like knowing ecu type by engine or something else ? Thanks
Hey Shemek Can you unlock Bosch ME2.0? Mercedes.
Have you reworked your clone or does it work out of the box ?
Its been reworked by me as every tool from China...unfortunately.
Thanks for fast answer.
can u tell me what do you rework?
do u do it like the picture on the net or do u have some special ideas ?
thank in advance
its been reworked mostly based on my experience and info from the net
Hello sir i already unlock ecu and save the eeprom then how to write flash file and eeprom for donor ecu
pleas help me bosch med 17.5 volkswagen golf 6 gti i have kessv2
good day Shemek, how much if i buy a copy of data used in Sd card on kess v2 4.036.tia
Plz help me i have pcr 2.1 ecm
Hi Shemek. Sorry to bother you again, but I have been looking through all of my Tuning Hardware and I have come across a OBD2 Bench Reading Cable, it has 7 Pinout Cables plus a Black Cable with a Croc Clip. Then there are two long Black & Red Cables with Croc Clips and there is a small Slider Switch, obviously to turn the box on and off, if you could provide an email address I could send you a photo of it, I was then wondering that if this item is OK you could let me know what wires goes on to what Pinouts please
I think if you put some voice comment in place in place the background music it will be much better
Hey Shemek
I had bought kess V2 clone from china Version 2.23.
When i try to do pcr 2.1 on that, it says "Invalid Protocol File"
Do you have any Idea, Why its saying That.
BTW Great Video. Keep Up
Regards From India
HI,
Did you ever get ID of that ECU with your new tool?via OBD or on the bench?
Hello
No Shemek, I do not get the ID of the PCR2.1
all I am getting is, Invalid protocol file.
But I do get ID for the other cars ECU.
clear you sd card and write back all files. will work after that for sure.
Отредактировать номер ВИН шасси этим клоном можно?
You can do it with avdi...its very easy.
Shemek Best avdi лучше, чем кесс к-таг галетто?
Hello sir
Great taste in music. For the most part a great mix.
Please help me ecu red
Please help me !
I only have two red wires (cable) for +12
and orange.... is the same
Hi
v
That so called "music" is UNBEARABLE!! PLEASE delete that awful racket, and put on something lower in tone and soothing; how about (1) you can do magic, by AMERICA. (2) cast your fate to the wind, by SOUNDS ORCHESTROL. 😎🙋
Nice song
Plz help me i have pcr 2.1 ecm
Contact me on bestdiagcar@gmail.com
PlZ send what up contact number