yes, too much mass, and he will be vibrating the hell out of that motor ... and his mount is way too flimsy for the raw torque that motor will put out.
+Rich Rebuilds The only problem with putting the motor on the swingarm is whenever you go to jump the quad the top of the motor will hit the bottom of the subframe.
Wanda Lawhern not the only problem. as others have mentioned it could shift weight bias, changes how motor torque affects traction, and adds a large amount of unsprung weight. but again i doubt this is going to be a trail ripper or handle any sort of air, it will still be awesome even if it completely compromises capability compared to itself in gas engine form.
I still think dropping it between the axles direct drive would be the best option get rid of the complication of the chain, lower the sprung weight etc. etc.
Converting an ATV to electric, is the toughest at all. I did three (Yamaha Rhino, Grizzly and Viking) , so I know what I am taking about.. Good Luck..!!!
Grainger??’!! Your 1st choice to go find a sprocket is grainger lol. There’s not some website out there that sells motorcycle parts?? Come on Uncle Rich!!??
You should oval out the mounting holes on the motor bracket. So you can adjust/tighten the chain. By moving the motor up and down. Keep up the great work man.
It was nice seeing your partner in crime (Lee), working the project with you. Nice meeting Phoenix who appears to be a cutie for sure. Good progress on your project, thanks for sharing.
Rich rebuilds go to Tractor Supply for chain sprockets. You can get the Hub in any size you want and a separate part with however many teeth you want then you weld the two together.
4:30 That is a "stupid idea", because your motor will be taking the same impact of the axle. Im not an expert, nor am I saying it wont work, but it probably wont last long and probably wont do well in the wet mud. Im in love with this project and this channel, and I hope it goes well.
Just think, impact that bent that swing arm/sa bolt will go into the motor before the shock absorber. It will also be interesting to see the weight distro of this setup.
Had my go at converting a small quad and i found belt drive a lot safer as there is more give/slip but then again with a proper controller you could adjust the initial power phase so you didn't get that jerk.
you are going to now have no swing arm travel what so ever because when you break it down the swing arm is thin for a reason. to let the shock travel come up into the sub frame. if you put this quad under any higher pressure to where the shock compresses you will smack the battery and after enough times eventually crack or damage the motor. if you can find a way to split the battery and have them hug the motor up in the frame that would allow for peak performance on the quad it self
Amazed by my uncle’s design skill. A real master. Guy, wait for very soon, a new line of summer clothes of High Fashion by Uncle Rich (use under your own description) 🤣🤣🤣🤣🤣
Hold a treat in your hand, when the dog focuses on it, move the treat towards him but in the air so he cant reach it and keep moving it towards him, once he cant follow the treat with his eyes / head anymore, he will sit so he can see the treat again, once he does you give him positive reinforcement :) I am really bad at explaining sorry :D
If you are not using some lubricant (oil) when you are drilling metal, your drill will get overheated and loose it's hardening. That is why it gets dull.
Mounting that motor on the swing-arm should be OK, as long as the mounting points on the motor itself can deal with the vibration (up & down motion) ...The constant flexing of the big-ass power cables might be a problem, a twenty inch long straight run should be OK for awhile, but may not last long.
The carbon belt that Zero use is made by GATES and it require alitnment with in 0.25 degree to not snap!.. so both axel/sproket MUST be very parallel and in line !
I think you can use water while trying to drilling steel and metal I think the metal get elastic when heated by friction. So adding water while drinking could make it easier to cut pleas read about this I am not sure.
Goddammit Rich! Your dad jokes kill me every time! "I know nothing about small packages...what I have is huge, and sometimes you have to work with what you've got." HAHAHAHA!!!
Oaft.... I think I would have been tempted to split that battery pack and fit it round the motor in the frame instead..... But still, canny wait to see it finished
So you did not want to extend frame? Even if was bolted together? Give you lots extra space. Maybe use jack shaft. You do not want that motor to be shaken to death with every bump.
The way you mounted the motor on top of the swingarm should work as long as the rear suspension doesnt move. Wait.. there is no airbox or battery under the seat now so it may work if the motor will fit inside the sub frame when the suspension cycles.
![โอ้เธอช่าง... - บี้เดอะสกา ft. ต๋อง เทวัญ (Prod. by ป๋าเพชร) [Official MV]](http://i.ytimg.com/vi/zbWhiLFmVL0/mqdefault.jpg)
CAD: Cardboard Aided Design
U get an A+ in sponsorship gig incorporation. 1:54
That's quite a bit of un-sprung weight on the rear axle. Just be cautious of the handling compromise that introduces.
Yeah, I was gonna say that...though not quite so elegantly.
It also changes the geometry of the suspension so now motor torque will not contribute to drive traction as the factory setup would have.
Wonder how it will do blasting through a foot of water and mud .....
@@andy1056 because we've seen Elon's do that. Is it supposed to be bulletproof too?
yes, too much mass, and he will be vibrating the hell out of that motor ... and his mount is way too flimsy for the raw torque that motor will put out.
I was so confused I thought he stuck a whole nerf dart into his ears
Fritz Storp timestamp?
@@nickhuff90 11:03
Imbigbad 11:45
same, i was thinking i didn't know you could do that with nerf darts
I like the flute censurer lol
+Rich Rebuilds The only problem with putting the motor on the swingarm is whenever you go to jump the quad the top of the motor will hit the bottom of the subframe.
Wanda Lawhern not the only problem. as others have mentioned it could shift weight bias, changes how motor torque affects traction, and adds a large amount of unsprung weight. but again i doubt this is going to be a trail ripper or handle any sort of air, it will still be awesome even if it completely compromises capability compared to itself in gas engine form.
I still think dropping it between the axles direct drive would be the best option get rid of the complication of the chain, lower the sprung weight etc. etc.
11:25 , use coolant!! or old oil to cool down the aluminum while drilling with the hole saw!. and use way slower speed, then it will really cut !
do it on a drill press, put the metal on a brick in a roaster pan full of any fluid - like water and it's flooded...
The nerf dart doubles as an extremely unnecessary q-tip.
Converting an ATV to electric, is the toughest at all. I did three (Yamaha Rhino, Grizzly and Viking)
, so I know what I am taking about.. Good Luck..!!!
He is easily the best at dropping ads of anyone in my feed. I appreciate that.
Had my brightness all the way up and got arc eyes just from watching them weld😂
Grainger??’!! Your 1st choice to go find a sprocket is grainger lol. There’s not some website out there that sells motorcycle parts?? Come on Uncle Rich!!??
Rad Stay At Home Dad it has to be a retailer located on the way to the train station. He uses an electric uniwheel to go that last last mile
LoL that place is so expensive.
Rocky Mountain would be so onboard
Brilliant! I can hardly wait for the next episode. This quad is gonna be awesome. Excellent work Rich, you're doing great!
That was the smoothest segway I have ever seen.
Use WD40 as lube when working with aluminum.
Paulman50 parafin is far better
Shits expensive dawg. Use margarine instead.
@@ryanqube9132 wait, will it actually work? It may work tho
WD40 if it gets too hot it catches on fire ... but works ok for Al tool lube
LMAO Duracell battery tutorial regarding manhood. Seriously laughing out loud!!
You should oval out the mounting holes on the motor bracket.
So you can adjust/tighten the chain.
By moving the motor up and down.
Keep up the great work man.
13:10 That’s definitely not your drawings lol 😂
why not?
@@mrcanpop did you see him drawing in this video? 🤣
I demand a Disney Princess car!! Just because the last one burned to the ground shouldn't make you give up that easily. Who are you Rich? Samcrac?
"I know nothing about small packages"...hehehe
I have a big package so I gotta work with what I have 😂😂😂😂
That's not what she said 😅
How big is battery and what kw size?
I've been waiting on a uncle rich video why do I check TH-cam everyday like I dont have notifications on😂😂
First Raid Shadow Legends ad I've actually watched
"....I know nothing about small packages....." Love it Rich!
It was nice seeing your partner in crime (Lee), working the project with you. Nice meeting Phoenix who appears to be a cutie for sure. Good progress on your project, thanks for sharing.
I love how you put in the little commercials, they don`t even bother me :). Also : "Aah 3 more hours" --> Story of my life bro.
You don't seem manually skilled at all, but you are able to get things done, and a quoter of million is watching. It means I must get there too.:)
Bro the Tesla shit is cool cuz the comedic value of Rich’s videos is too good
Rich is the absolute best at the sponsorship inserts.
“What I have is huge and sometimes you’ve gotta work with wat u got” Rich 2020
DO you have a way to adjust tension on that chain when it wears and gets loose?
Darkhorse393 doesn't look like it to me.
Just as regular raptor, You loosen the clamp bolts and the bearings of rear axle (outer part) rotate moving it on a circle.
I thought Raid Shadow Legends didn't' sponsor anyone? My parody commercial is a lie now!
Wow, that's great! Love the way you maxed out unsprung weight to save on shock wear.
You compensate many things I would like to know with a humor I never get tired of. That flute 12:26....
Chain link remover tool is like $15 online. Or harbor freight.
Also, you DESPERATELY need a 4 1/2", or 7" grinder (especially to use between welds)
Rich rebuilds go to Tractor Supply for chain sprockets. You can get the Hub in any size you want and a separate part with however many teeth you want then you weld the two together.
4:30 That is a "stupid idea", because your motor will be taking the same impact of the axle.
Im not an expert, nor am I saying it wont work, but it probably wont last long and probably wont do well in the wet mud.
Im in love with this project and this channel, and I hope it goes well.
Just think, impact that bent that swing arm/sa bolt will go into the motor before the shock absorber.
It will also be interesting to see the weight distro of this setup.
I think he needs an industrial laser cutter
that's a fact!!!
@@mollywapyo costs too much. They're doing a relatively good job considering the tools they are working with
@@nikosv8166 not if you get sponsored :p
What I have is huge and sometimes you got to work with what you got lol
Had my go at converting a small quad and i found belt drive a lot safer as there is more give/slip but then again with a proper controller you could adjust the initial power phase so you didn't get that jerk.
you are going to now have no swing arm travel what so ever because when you break it down the swing arm is thin for a reason. to let the shock travel come up into the sub frame. if you put this quad under any higher pressure to where the shock compresses you will smack the battery and after enough times eventually crack or damage the motor. if you can find a way to split the battery and have them hug the motor up in the frame that would allow for peak performance on the quad it self
smack the motor sorry
Try methylated spirits as lubricants when drilling in aluminum 💦
Rich’s videos are always better when Lee is featured. More Lee videos please.
I love that Moby has a side gig welding sprockets.
damn you premier!!!! bamboozled again!!!
first raid sponsor spot I did not insta skip, good content Rich
I hate ads but I must admit, that was a funny and smooth ad transition.
How are there 3 thumbs down and the video hasn't even started? Haters
John Huey they are just jealous of his youth, beauty and success
You defy all engineering logic, safety and most importantly - viewers.
The first sponsor I didn't skip on TH-cam... Nice work LOL
Pretty creative. It's going to handle strange with that huge battery and all that weight on the swingarm. The first jump may be the last.
The #50 industrial sprocket that you have is the same exact size as a 530 motorcycle chain. You can find them pretty easily.
Awesommme. Excited for that final bodywork
The sound of a recorder makes an infinitely more funny censor sound than the original bleep! Oh my gosh
I dont know why the fuck am I so addicted to your videos. But Im glad I am
This channel inspires me to teach everyone who's interested to fabricate properly....
12:15-12:27 Felt like I was watching The Red Green Show.
Peace Love Classic
Amazed by my uncle’s design skill. A real master. Guy, wait for very soon, a new line of summer clothes of High Fashion by Uncle Rich (use under your own description) 🤣🤣🤣🤣🤣
3:15 "...but what I have is huge, and sometimes you have to work with what you've got."
You and me both, brother.
Anyone who told you to go belt drive is wrong. Great series, looking forward to the next one.
Hold a treat in your hand, when the dog focuses on it, move the treat towards him but in the air so he cant reach it and keep moving it towards him, once he cant follow the treat with his eyes / head anymore, he will sit so he can see the treat again, once he does you give him positive reinforcement :) I am really bad at explaining sorry :D
My cat goes wild on this video and demands catnip..
"I know nothing about small packages...installs big black box". Priceless
If you are not using some lubricant (oil) when you are drilling metal, your drill will get overheated and loose it's hardening. That is why it gets dull.
@Rich Rebuilds
You should think about moving your lathe away from your grinder. The abrasive dust is horrible for the ways on your lathe.
Alot of work invested, earned a sub here
watching this makes me glad i have unlimited access to CNC mills...
Mounting that motor on the swing-arm should be OK, as long as the mounting points on the motor itself can deal with the vibration (up & down motion) ...The constant flexing of the big-ass power cables might be a problem, a twenty inch long straight run should be OK for awhile, but may not last long.
Plot twist, this is the actual Cyberquad, episodes were filmed months in advance!
This is why Rich is the man!!!!!!!!
The carbon belt that Zero use is made by GATES and it require alitnment with in 0.25 degree to not snap!.. so both axel/sproket MUST be very parallel and in line !
Rich does what i wish i could if i didnt have to work so hard to pay bills. GO UNCLE RICH!!!!!
I think you can use water while trying to drilling steel and metal I think the metal get elastic when heated by friction. So adding water while drinking could make it easier to cut pleas read about this I am not sure.
Wow Raid Shadow Legends sounds really neat, I've never heard of that.
I was about to shut this shit off after the 10 minutes of drawing class on cardboard. Thank good the doggy showed up and saved the video.
Goddammit Rich! Your dad jokes kill me every time! "I know nothing about small packages...what I have is huge, and sometimes you have to work with what you've got." HAHAHAHA!!!
Haha CAD Design (cardboard aided design) at its finest. Love it.
Adorable New Shop Husky Puppy!! 10:30
Oaft.... I think I would have been tempted to split that battery pack and fit it round the motor in the frame instead..... But still, canny wait to see it finished
8:11 Richie on AutoCAD
Dang, all that time learning CAD, and it turns out all I needed was a Sharpie and a box on its way to the recycle bin.
whats good yall
waiting and commenting on my comment while waiting
if i reply to a reply and i still replying to my first self or both, or maybe just my last self
is it selfish to reply to myself?
who knows
I can’t wait to see the 1001st episode, when we actually gonna see this beauty drifting around 😂
So you did not want to extend frame? Even if was bolted together? Give you lots extra space. Maybe use jack shaft. You do not want that motor to be shaken to death with every bump.
Use ethanol as lubricant/cooling the next time you cut or drill aluminium.
Best ad placement of all time! lol
Time goes by and uncle rich doesn't change. You get an A for consistency lol
That dog stole the show. Need more videos on the dog.
The way you mounted the motor on top of the swingarm should work as long as the rear suspension doesnt move. Wait.. there is no airbox or battery under the seat now so it may work if the motor will fit inside the sub frame when the suspension cycles.
3:05😂😂😂😂 Rich is at it again 😂😂
Now is the time on Sprockets when we dance...
Waiting to see “welding with uncle rich”
Invest in a plasma cutter , learning alot from your channel about evs thanks for going through the headaches to teach .
My son is 7 and my daughter is 8 and I got atleast 15 plastic trick or treat buckets that are ofcourse filled with some kind of c shift r fluid lol..
Sharpie on a cardboard box "I know it's not 3D". DEAD!
this was a great video keep the good work up and a good attitude
The whole video seamed to be ... Rich 'NOT WELDING' until 8:45 you hear him say he has to weld... and then his friend does it.... LOL
@rich sick build! btw you got any model 3 bodyparts laying around?
Safety equipment? I didn't see any steel toed flip flops!
My first premiere cherry popped
That's what all the girls say...
Slinky lol
How to turn a raptor into a Trainwreck part III. :) Great comedy though. ;)
*I'm Routing for you Bro! I recently just got into the whole "Travel" of discovery!*