xTool RA2 Rotary Assembly in detail
ฝัง
- เผยแพร่เมื่อ 2 มิ.ย. 2024
- An explanation of parts and assembly in detail of the many different modes the xTool RA2 laser rotary accessory has.
I already have a xTool D1 laser in use and adding a second dedicated to use with the RA2 rotary.
This video covers only the assembly and explanation of the RA2 along with a brief look at the new xTool D1 after assembly as I get it prepped and tested. More videos showing the many modes in use to come soon!
Links to items used: (Disclosure: I do receive a small commission if you purchase any of these items. This does not increase your cost)
Direct from Makeblock:
XTOOL D1 Laser + RA2 Rotary + 2 Riser Sets: www.xtool.com/products/portab...
XTOOL RA2 Pro Rotary: www.xtool.com/products/xtool-...
XTOOL Risers (8 PACK): www.xtool.com/products/xtool-...
XTOOL D1 10W Laser: www.xtool.com/products/portab...
From Amazon:
XTOOL D1 10W Laser: amzn.to/3wRLcJk
xTool RA2 Pro, 4-in-1 Laser Rotary: amzn.to/3wKYGXe - แนวปฏิบัติและการใช้ชีวิต
![[4K] TREASURE(트레저) “KING KONG” Band LIVE Concert 킹콩은 라이브를 찢어🦍 [it’s KPOP LIVE 잇츠라이브]](http://i.ytimg.com/vi/p8bLLOxPDD8/mqdefault.jpg)
Thank you!
Thank you! That beat trying to read the manual!
I was baffled on how to tighten the little sprocket, THANK YOU!!
Thank you so much for doing this video. So much easier than trying to navigate the manual!
that was a great video and that’s such an awesome accessory
by the way, restless heart was an awesome band and one of my favorites as well
The meat of this vid starts right around 9:17 (You're welcome)
Support roller @ 10:39
Roller re-insert 11:35 (under the belt)
The magic for the chuck belt drive is right @ 14:00!
My good deed for the day is done. :) Enjoy.
What type of connector is for the stepper motor? Does it come with alternative connectors? 3 pin, 4 pin?
Thanks!
Great video, but a few times your parts were out of camera view, makes it confusing for beginners like me.
you never attached the rotary to the xtool. Why doesn't anyone show this?
That is a whole different video subject matter (I am guilty of not making one yet) as is dependent on not only the laser model, but the software being used, and how to set it up in that software. I do intend on making some videos on this sometime this winter.
I noticed a slight start and stop in the video when you were installing the sprocket @ 13:58. Did you have problems with the sprocket sliding on the shaft? Mine will not go on the shaft and yes, I have double checked to make sure the set screws are not interfering. Any ideas before I contact customer service?
I edited out the portion where I dropped one of the set screws because I had backed it out too far and had to find it amongst the sawdust on the floor.............. Otherwise, I had no problem sliding it on.
I am having the same problem. I took both set screws completely out and still having trouble. Did you ever figure out what the issue was?
My belt is to tight to screw down my spiny thing :/
Where can I find the grid file you are using. Thank you for you videos.
www.thingiverse.com/thing:5098673 is a "base file" and runs in Laserbox. Mine has a few modifications dedicated to projects that I do for quick layout. The mods were done in Lightburn.
@@rogersshop thank you
@@rogersshop Will this link open up in Lightburn?
@@jdo62 No. Laserbox only.
@@rogersshop thanks for that info. Now to see if I can find something that will open in Lightburn to use...
Can I leave the sprocket on or best to remove it?
I left it on. It is not in the way, and is one less part to keep track of!
7 Minutes in and still no assembly sorry but I'm going to find somebody else who will actually get to the point!
This goes into great detail for a reason. If you don't like it, move on.........
@@rogersshop I did thanks for your approval.
why be such an a$$ about it? He's taking time to share what he has learned. If you don't like it get off of TH-cam.