Please reverse tuning screw slightly and try. Have you pulled the choke and pumped petrol bulb sufficiently? Tuning: remove your spark plug and pour a little petrol into it and burn. Use a zero grade paper to clean the sparking points. Remove all carbon from plug. Adjust gap to 20 inch thou inc . i.e. thickness of an old post card. Check spark plug by pulling the thread with earthing the with m/c body. Spark should be jumping well and bright. Put the plug back . Pump petrol and off the choke. Start m/c and let it run a few seconds. Now switch the choke and adjust carburettor screw to run the m/c fast. Turn the screw back and listen to the m/c running slower. At one point it will become least or even the machine will stop. Bring back to minimum position and start. Raise and like what you were experiencing, the m/ c will stop. Advance screw by a quarter turn and try. If it stops again increase by another quarter. You will notice that the speed goes to the maximum as you turn up the throttle. Your m/ c should give optimum milage and power now. If you still doubt, change the plug and see. This is the simplest. Next stage will be checking the carburettor which, though not very difficult, be better given to an experienced mechanic. Even a motor cycle mechanic will repair the carburettor. If you still feel the strength insufficient you will have to see the clutch. ( Hope you have pumped enough grease to the gear assembly and your tap and go or the blade are o.k.) This also may be attended to by an experienced mechanic though you can learn it easily if the mechanic teaches you. It is better to get the clutch checked if you feel that the power of machine has come down.
Good presentation. Thanks
Super അവതരണ ശൈലി.ഗുഡ്
Thank you🙏
2stroke അഗ്രി നല്ല മെഷീൻ ആണോ 15500 പ്രൈസ് paranje
Very good and useful talk without wasting time. Omitted greasing which is very important .
Thank you so much for your support
Super
Super presentation.
Thank you
നല്ല Nylon wire എവിടെ കിട്ടും കമ്പനി പേര് അറിയുമോ .....? നിങ്ങളുടെ കൈയിൽ ഉണ്ടോ ..?
Tranprent square wire varunnunddu athanu ettavum nallathu. നിങ്ങൽ എവിടെയ് ഉള്ള aala സ്ഥലം പറയമോ
Bro rover 2 stroke machine aganae unde.spares kittumo
Pls reply thank u
Depending on company
Net type Helmet എവിടെ കിട്ടും
Amazon
ഇതിന്റെ ഹെഡ് ഏതാ ഉപയോഗിക്കുന്നത്
Head means?
Blade vakumbo vibration varunathu angana maattaa
ബ്ലേഡ് sizes kurachal mathi / allenghil blade bend undakum
Kasei brush cutter നെ പറ്റി എന്താണ് അഭിപ്രായം മൈലേജ് എത്ര കിട്ടും. ?
2-3 hrs but spare parts is too costly and very less availability also.
Entaduthulla brush cutter Honda 4 stroke.. അതിൽ blade aanu ഉള്ളത്.. അത് ഇത് പോലെ wire ആക്കാൻ പറ്റുമോ... ബ്ലഡ് / വയർ വച്ചാൽ ഉള്ള difference എന്താ
Blade um vsyarum vachal kattiyullatum allthathum aaya pullukal orumichu kalayan sadikkum. Vayar matharamanenghil kattiyullapullukal pokilla
@@abijithpoluvalappil4560 രണ്ടും ഒരുമിച്ച് വെക്കാൻ പറ്റുമോ..
മെഷീൻ നു നല്ലതല്ല @@travelstoriesbynoufal
Oru hasqwarna machine vaangi 5 hours use cheythittundaavum ippol raise aakkumbol off aayi povunnu. Reason enthaayirikkum paranju tharumo
No idea
Please reverse tuning screw slightly and try. Have you pulled the choke and pumped petrol bulb sufficiently?
Tuning: remove your spark plug and pour a little petrol into it and burn. Use a zero grade paper to clean the sparking points. Remove all carbon from plug. Adjust gap to 20 inch thou inc . i.e. thickness of an old post card. Check spark plug by pulling the thread with earthing the with m/c body. Spark should be jumping well and bright.
Put the plug back . Pump petrol and off the choke. Start m/c and let it run a few seconds. Now switch the choke and adjust carburettor screw to run the m/c fast. Turn the screw back and listen to the m/c running slower. At one point it will become least or even the machine will stop. Bring back to minimum position and start. Raise and like what you were experiencing, the m/ c will stop. Advance screw by a quarter turn and try. If it stops again increase by another quarter. You will notice that the speed goes to the maximum as you turn up the throttle. Your m/ c should give optimum milage and power now. If you still doubt, change the plug and see.
This is the simplest. Next stage will be checking the carburettor which, though not very difficult, be better given to an experienced mechanic. Even a motor cycle mechanic will repair the carburettor.
If you still feel the strength insufficient you will have to see the clutch. ( Hope you have pumped enough grease to the gear assembly and your tap and go or the blade are o.k.) This also may be attended to by an experienced mechanic though you can learn it easily if the mechanic teaches you. It is better to get the clutch checked if you feel that the power of machine has come down.
ഇതിൽ
ഗ്രീസ് വേണ്ടേ
ഗ്രീസ് വേണം. ആവശ്യം ആണെങ്കിൽമാത്രം
Net type helmet എവിടെ കിട്ടും
Thrissur Pattikad agri tools or Amazon
No please
നെറ്റ് ഹെൽമെറ്റ് എവിടെ കിട്ടും
Pattikad
97448 80795
നെറ്റ് ഹെൽമറ്റ് എവിടെ കിട്ടു o എത്രയാ വില
Thrissur pattikkad Shop name Agri Tools Rs. 350/-
സേഫ്റ്റി ഗാഡ് ഫിറ്റ് ചെയ്തില്ലാ മറന്ന് പോയൊ
Nan athu upayokikkarulla, bharam koodum. Pinney kurachu carefully cheyyanam ennu mathram
ഈ ഹെൽമെറ്റ് വിൽക്കുന്ന ഷോപ്പിലെ ഫോൺ നമ്പർ ഒന്ന് തരാമോ
9744880795
👍
എന്റെ കിസ്സൻ ക്രാഫ്റ്റ് മെഷീൻ ആണ്. അതിൽ വലിയ ബ്ലേഡ് ഉപയോഗിക്കാമോ.. കമ്പനി സ്റ്റാർ ടൈപ് ബ്ലേഡ് ആണ് തന്നിരിക്കുന്നത്
Ethara cc aanu
@@abijithpoluvalappil4560 40 cc
Number plz
9164973437