great job i use a sponge brush as well to lay down the urethane ,but i apply it with a foam roller and then put the roller and tray with tray liner into a trash bag, blow a little air in there and a sqeeze clamp to keep it airtight. Then i can use that same roller and tray over and over.
I have the same US Cutter machine, but have never learned how to use it. It looks like you’re in Texas like I am. I’d love to come build a set with you and learn house to use the Cutter machine.
Your finished product is great! Amazing job! The sprayer "should" do a better job then the brushes, maybe you have to adjust your setup a bit. Regardless, as I first stated amazing product at the end. Amazing work ethic and attention to detail!!!
Thank you so much for sharing! You are by far one of the best video tutorials out there. Like below, I would love to see the name of the paints and stains you are using. I even learned something new with the stencils and reg marks. LOVE IT! How do we order one from you?
Sorry...Ive been neglecting my page recently. I use the Rustoleum 2X primer and paint combo spray paints and the Valspar Water Based Semi Gloss from Home Depot.
Great video! Thanks for the tip about using registration marks for multi-color vinyl stenciling. I'm about to paint my first cornhole board with vinyl stencil graphics, but only a single-color for my first go at it. This is just the video I was looking for. Do you ever stain the wood before the initial clear coat? Thanks.
What grit do you sand with before you actually lay your stencil? Also is you clear coat you use in the beginning the same clear coat you use in the end to finish your boards?
I really appreciate your videos. Thank you. I could really use your advice on a set of boards I’m working on. It’s my first time with layered colors and the bottom layer keeps peeling up after I try to pull off the oracal mask stencil that is being used for the top layer. Any ideas?
Sorry...Ive been neglecting my page recently. I hope your set turned out OK. I don't usually have trouble with paint peeling if I use 3 coats of clear under the color. If you just paint right onto the bare wood it will peel up.
Sorry...Ive been neglecting my page recently. I use the Rustoleum 2X primer and paint combo spray paints and the Valspar Water Based Semi Gloss from Home Depot.
Wait, so you take off the backing and put it back on a couple inches higher? Why not just peel a couple inches off the bottom and cut off a small strip?
Yeah the music was way too loud. And it wasn't even needed when your talking. Some ppl may complain about the type of music, that doesn't matter. It's the loudness and effort ppl have to make to listen to you talk and ignoring the music. Best of luck!
Wow. Great craftsmanship man.
Nice Job Buddy! Super detailed
Those look incredible.
Awesome work! Your patience far exceed mine.
Nice work! I'm making a few sets right now and it does take a lot of work to get these boards to look nice and make them useable.
Liked the video and would love to see the list of what you use with the links. Really like your stencil maker/cutter!! Awesome video!!!!
Great video! Did you use the same process for the fire department boards? If so, how many stencils did that one need?
great job
i use a sponge brush as well to lay down the urethane ,but i apply it with a foam roller and then put the roller and tray with tray liner into a trash bag, blow a little air in there and a sqeeze clamp to keep it airtight.
Then i can use that same roller and tray over and over.
I have the same US Cutter machine, but have never learned how to use it. It looks like you’re in Texas like I am. I’d love to come build a set with you and learn house to use the Cutter machine.
Your finished product is great! Amazing job!
The sprayer "should" do a better job then the brushes, maybe you have to adjust your setup a bit.
Regardless, as I first stated amazing product at the end. Amazing work ethic and attention to detail!!!
Great work, what is your vinyl cutter and what do you use for vinyl? If you don’t mind me asking?
Thank you so much for sharing! You are by far one of the best video tutorials out there. Like below, I would love to see the name of the paints and stains you are using. I even learned something new with the stencils and reg marks. LOVE IT! How do we order one from you?
Sorry...Ive been neglecting my page recently. I use the Rustoleum 2X primer and paint combo spray paints and the Valspar Water Based Semi Gloss from Home Depot.
Great video! Thanks for the tip about using registration marks for multi-color vinyl stenciling. I'm about to paint my first cornhole board with vinyl stencil graphics, but only a single-color for my first go at it. This is just the video I was looking for. Do you ever stain the wood before the initial clear coat? Thanks.
I do stain on occasion. If I do...I clear coat on top of it before laying graphics.
What grit do you sand with before you actually lay your stencil? Also is you clear coat you use in the beginning the same clear coat you use in the end to finish your boards?
Great job! How can I get ahold of you? Have a project that I like to go over with you
Really great video! What vinyl cutter do you use and does the software for it work with an apple laptop?
Sorry...I've been neglecting my page recently. It is the US Cutter MH 721. I have a surface pro so don't know about apple compatibility. Thanks.
Goodness that’s a lot of time but awesome!
I really appreciate your videos. Thank you. I could really use your advice on a set of boards I’m working on. It’s my first time with layered colors and the bottom layer keeps peeling up after I try to pull off the oracal mask stencil that is being used for the top layer. Any ideas?
Sorry...Ive been neglecting my page recently. I hope your set turned out OK. I don't usually have trouble with paint peeling if I use 3 coats of clear under the color. If you just paint right onto the bare wood it will peel up.
are you able to list the products you use in the video? specifically the spray pains and clear paints? thanks!
Sorry...Ive been neglecting my page recently. I use the Rustoleum 2X primer and paint combo spray paints and the Valspar Water Based Semi Gloss from Home Depot.
what kind of stencil paper do you use?
What thickness is the plywood?
What type vinyl is that
Great stuff! What kind of clear coat did you use please?
Sorry...Ive been neglecting my page recently. I use the Valspar Semi-Gloss water based clear. Home Depot $69 gal.
@@cubmasterdarren thanks
Last question! Do you find putting down a couple clear coats on the top before painting prevents bleed through?
@@livingthedream29 absolutely. I even put a coat of clear on top of the stencil sometimes before I put additional coats of color.
What graphics design program are you using to import into SCAL?
Sorry...Ive been neglecting my page recently. I use the US Cutter software that comes with the vinyl cutter. Thanks so much.
do you have video on the attachment on the hardware and accessories
Sorry...Ive been neglecting my page recently. Yes. The how to build cornhole boards videos have sections about the hardware. Thanks for watching.
Wait, so you take off the backing and put it back on a couple inches higher? Why not just peel a couple inches off the bottom and cut off a small strip?
lose the music, I got a headache which means no like and no subscribe. Sorry
Yeah the music was way too loud. And it wasn't even needed when your talking.
Some ppl may complain about the type of music, that doesn't matter. It's the loudness and effort ppl have to make to listen to you talk and ignoring the music.
Best of luck!
Agree. Nasty music, i always ask why?
Great job!!! I use that same paint for my projects including the clear coat and they work great!
Hi there - I’m looking for some direction and notice your comment and that you may be able to help? I made a new comment explaining my issue.