I noticed you did not put silicone greas on the secondary o - ring. I removed my secondary o-ring and greased it and it just does not stay in place when I tried to replace it. Has anyone that you know had simular problem?
In the video you did the vacuum pump > then submerged to test without the camera. Would you then place the camera in the housing and do the vacuum pump again and test again?
Hola ! Cómo estás.? Muchas gracias por toda la información, pero tengo una pregunta! Hace 5 días tengo el housing con mi cámara Sony a6400! Luego de 1 , 1 1/2 hora estando en e, agua mi port Lens tiene humedad! Tal que no sale bien la fotografía ! Como puedo solucionarlo?
I bought one for my Fujifilm XT3 and have opened it to get familiar. After I removed my XT3 it started beeping. How do I turn off the alarm that is beeping now? Also a red light.
at 11:49 , ⬆video, after 15min - 30min, how consider? if green lights gone changed red, I can't use housing? what's (how read) result on vacuum test? want to know test was success or not...
I have the Sony A7RV Housing and when the camera is in, the housing doesn’t close properly. Before inserting the camera, the housing passes the vacuum pump test easily and after the camera is in the housing doesn’t close properly in the bottom left corner. Any suggestions or is this a construction error?
Does Sea Frogs sell a port cover for the housing? i travel often and do so with the dome port off and would like to find a cover for the housing's port hole.
Yes before the first use, and then you need to continue to maintain the housing, clean O-rings and grooves from sand and dirt after 5 use of housing if needed. Very important! to not stretch the O-rings during the cleaning process. Also please watch this video: th-cam.com/video/LRPIkPvOOtw/w-d-xo.html
Hi, can I use the vacuum pump underwater to keep the camera bouyancy in check? oor is there some way to take the air out of the case and keep it sealed?
Unfortunately, it is not advisable to use VPS-100 valve in the water as per manufacturer instructions. So after checking the unit please remove it and replace it with the port cap. If you want to control buoyancy, add weights to your setup to make it as close to neutral as possible.
Hello. I have used seafrogs on all my camera models, from old Canon, to my Olympus TG5 and TG6, and also for my sony rx100 iV and Vii, sony a6300, sony a6500, sony A7 Ii, and now sony A9. They are super durable if we don't skip proper care. I also have tons of expansion ports, domes, etc and the vacuum pump for leak detection. Super! One question, if you know: on my a9 housing, as well on that model you showing for the a7 R III, there is a small button wheel on the front, right above the port. I am trying hard to understand what that is for... the cameras have no buttons there... the focus ring don't seem to touch it (I have the old hard plastic ones but now there are some rubber more soft ones...). I thought it was to help get them aligned withe the cogwheel down by the base but I don't think its that either.. any ideas? Thanks.
@@igorshtorm71 yeap it is, thanks! Actually it works well. Depending on the lens used (and there are many lenses compatible with several focus/zoo rings) the ring tends tonoscilate a little. This helps keep it straight so the gear knob don't miss the dents. Thanks.
Hello Enea. Housing for a7Riii compatible with both a7iii and a7R iii cameras. Housing for a7Riv is not compatible with a7 iii camera. seafrogs.com.hk/collections/sony/a7-iii
Are the normal Sea Frogs ports compatible with Salted Line cases? The Salted Line and the Seafrogs 6" dry domeports (67mm / 80mm) look exactly the same. (even the same pictures online) Thanks!
Hello Andres. No, ports for regular Sea Frogs housings are not compatible with Salted Line housings as the diameter of the lens entrance is different, 90mm Sea Frogs vs 80mm Salted Line
Hello Tomris, we include silicone grease in every package, however, if you bought your housing from any other seller rather than www.seafrogs.com.hk , then please contact your seller directly and confirm what they include in the package. Otherwise, please contact support@seafrogs.hk and mention your order ID number.
I noticed you did not put silicone greas on the secondary o - ring. I removed my secondary o-ring and greased it and it just does not stay in place when I tried to replace it. Has anyone that you know had simular problem?
Hello Douglas. Please watch this video: th-cam.com/video/Zl33lbuMfJg/w-d-xo.html
This is the most informative video about this housing I have seen. Thank you.
Glad it was helpful!
Do you need the vacuum pump for general water use or is that just for diving?
Nice video. Very informative. I have one coming for a Sony HX90 but guess it won`t need as much attention as this model.
In the video you did the vacuum pump > then submerged to test without the camera. Would you then place the camera in the housing and do the vacuum pump again and test again?
I didn't get why do you test the camera underwater without the valve even if you used the valve no the previous step?
when I remove the pump valve I can see to sensed of camera housing why?
Hola ! Cómo estás.? Muchas gracias por toda la información, pero tengo una pregunta! Hace 5 días tengo el housing con mi cámara Sony a6400! Luego de 1 , 1 1/2 hora estando en e, agua mi port Lens tiene humedad! Tal que no sale bien la fotografía ! Como puedo solucionarlo?
I bought one for my Fujifilm XT3 and have opened it to get familiar. After I removed my XT3 it started beeping. How do I turn off the alarm that is beeping now? Also a red light.
I mistakenly removed my secondary o ring and have had alot of trouble putting it back on. Do you have any recommendations?
Hello I have a housing for the Fujifilm x100t. Does the dome port unscrew? I cannot seem to remove it to grease the dome o ring.
Does the exterior of the lens need any treatment as you would a diving mask. Like an anti-fogging spray or something.
How do you take ports off for Sony a7 mk 1 white housing
Very helpful thanks for sharing
at 11:49 , ⬆video, after 15min - 30min, how consider? if green lights gone changed red, I can't use housing? what's (how read) result on vacuum test? want to know test was success or not...
I have the Sony A7RV Housing and when the camera is in, the housing doesn’t close properly. Before inserting the camera, the housing passes the vacuum pump test easily and after the camera is in the housing doesn’t close properly in the bottom left corner. Any suggestions or is this a construction error?
Please write to our support team. They will assist you with a solution ASAP. seafrogs.com.hk/pages/customer-support
Does Sea Frogs sell a port cover for the housing? i travel often and do so with the dome port off and would like to find a cover for the housing's port hole.
My sigma 24-70mm lens port does not 'click' when attached, neither does it stay locked once I screw the lock back on. Is that it?
Please contact support@seafrogs.hk , mention your order ID number, and our support team will back to you with the solution. Thank you
What about manual focus lenses? Can the zoom gears be ordered seperatly?
please check available zoom gears here: seafrogs.com.hk/collections/zoom-gears
How many time I have to make this procedure? Only for the first use?
Yes before the first use, and then you need to continue to maintain the housing, clean O-rings and grooves from sand and dirt after 5 use of housing if needed. Very important! to not stretch the O-rings during the cleaning process. Also please watch this video: th-cam.com/video/LRPIkPvOOtw/w-d-xo.html
Will there be fujifilm xt4 housing coming out soon?
can I vacuum test after water test?
Hi, can I use the vacuum pump underwater to keep the camera bouyancy in check? oor is there some way to take the air out of the case and keep it sealed?
Unfortunately, it is not advisable to use VPS-100 valve in the water as per manufacturer instructions. So after checking the unit please remove it and replace it with the port cap. If you want to control buoyancy, add weights to your setup to make it as close to neutral as possible.
My port does not click at all. Is that normal?
i have the dome and i have alot of vignetting. Any idea how to fix this?
To avoid wiggetting you must use the correct port for your lens. You can find this information at www.seafrogs.com.hk
you didn't clean the big o-ring in the black part of the case. why not? this one is really challenging to put back in!
Hello Tobias, please watch this video regarding how to maintain the main O-rings: th-cam.com/video/Zl33lbuMfJg/w-d-xo.html
Hello.
I have used seafrogs on all my camera models, from old Canon, to my Olympus TG5 and TG6, and also for my sony rx100 iV and Vii, sony a6300, sony a6500, sony A7 Ii, and now sony A9. They are super durable if we don't skip proper care. I also have tons of expansion ports, domes, etc and the vacuum pump for leak detection. Super!
One question, if you know: on my a9 housing, as well on that model you showing for the a7 R III, there is a small button wheel on the front, right above the port.
I am trying hard to understand what that is for... the cameras have no buttons there... the focus ring don't seem to touch it (I have the old hard plastic ones but now there are some rubber more soft ones...). I thought it was to help get them aligned withe the cogwheel down by the base but I don't think its that either.. any ideas?
Thanks.
Thats a zoom gear locking pin, so it won't slide backwards (not that it does imho), but I assume jsut a precaution in case it does.
@@igorshtorm71 yeap it is, thanks! Actually it works well. Depending on the lens used (and there are many lenses compatible with several focus/zoo rings) the ring tends tonoscilate a little. This helps keep it straight so the gear knob don't miss the dents. Thanks.
I have a sony a7 iii. Bit confused on what housing I should get. The one for a7Riii or the one for a7Riv? Which one also fits a7 iii?
Hello Enea. Housing for a7Riii compatible with both a7iii and a7R iii cameras. Housing for a7Riv is not compatible with a7 iii camera.
seafrogs.com.hk/collections/sony/a7-iii
Are the normal Sea Frogs ports compatible with Salted Line cases? The Salted Line and the Seafrogs 6" dry domeports (67mm / 80mm) look exactly the same. (even the same pictures online) Thanks!
Hello Andres. No, ports for regular Sea Frogs housings are not compatible with Salted Line housings as the diameter of the lens entrance is different, 90mm Sea Frogs vs 80mm Salted Line
@@seafrogswaterproofhousings Thanks for the quick response! =D
How are you in live view when the eye piece is blocking the eye sensor?
Hello. Go to your camera menu, and choose LCD monitor only
it is obvious for me but still it's very nice manual, tnx!
You're welcome!
How do you take the port off
mine didnt come with any silicon grease. What should I do? Is it already assambled for me?
Hello Tomris, we include silicone grease in every package, however, if you bought your housing from any other seller rather than www.seafrogs.com.hk , then please contact your seller directly and confirm what they include in the package. Otherwise, please contact support@seafrogs.hk and mention your order ID number.
This is camera suitable for ROV.. ??.. Streaming is possible
unfortunately, no
Do you reapply grease before every dive?
we suggest you clean O-rings and reapply silicone grease every few sessions, depending on how hard do you use it
When are you guys restocking the pump?
Hello Gia, after 1 week approx.
the vacuum pump comes with every housing ?
No, and you need to purchase it separately seafrogs.com.hk/products/vacuum-pump-system-vps-100
@@seafrogswaterproofhousings is it an essential for the use of the housing?
what it is major usage for?
@@mohameddiaa7444 create professional photo and video content in the water environment
seems like a lot of stuffing around, might use a go pro :):)
Great information, music is too loud.