Nice job on the video! Have the same unit and noticed the brushes were not spinning. Disassembled and observed the bearings were completely frozen from rust. Soaked them in PB blaster and they freed up. Appreciate your help in the repair!
I followed what you did and it worked!!!!! I swear I was about to put it on the curb and get something else but I decided to give this a try and now I am back in business. If you are ever in the Boston area I owe you a beer or two or three!! Thanks so much.
@@handcraftedoverlanding I guess the motor was burned out. It’s under warranty so they don’t make parts for this anymore. I’m gonna replace for free the entire unit.
I had an interesting problem with a Power Scrub / Spin Brush model... the handle would not pull hard enough to open the spray valve so no water came out. It is under the curved panel on the back side on the Power Scrub (where your knees would hit when your pushing it with the handle up) and found the valve. There was too much flex in the actuating rod from the water spray trigger/handle to push open the valve. I glued a small (1/2" square) piece of plastic I cut from an old storage container handle (about1/8" thick) to the actuating rod where it contacted the valve to make it just a tad longer and push harder so now works great !! Cost nothing!... Hope that helps someone.
My brushes won’t spin. I also cannot get water to come spray out. Do these go hand in hand ? I can’t find any issues with water flow like air in the line etc.
I am so thankful for you!!!! The only problem I had with my spinscrub was my chinchilla chewing through the cord. I found a new one on ezvacuum and was able to do a tear down thanks to your video. I could not find a SINGLE tutorial or any information at all on where the heck the cord wiring lives on the inside or how to get to it, but your video gave me the confidence to keep going and look for it myself. I figured, oh well, it's either keep looking and mess with this thing and throw it away, or throw it away, and buy a new one anyway. So after MUCH removal and even more teardown (I stupidly took zero pictures before continuing to rip everything apart) I finally found the compartment with the wiring!! Replaced it all on my own and after much guessing of how to get everything back, I was in tears when I turned it on and it was screaming at me after three sad years of it being dead 🥺😭 I am a 32 year old female and I'm just so proud that I was able to figure it out. Thank you for giving me the confidence and for showing the initial teardown!! I am so happy.
I'm so proud of you! You did a great job and sounds like you expanded your knowledge at the same time. It's amazing the strength and skills we have hidden until we take that leap and discover them! Great job!
I have to wonder....when you're done using the unit... if you put a fan to blow through the screen for a few hours so air blows through there and dries it out....this is what I've always done and my brushes haven't stopped spinning... Knock on wood. I really LOVE these cleaners they suck almost all the water back up....and are so easy to use and clean...I wish they made them better.
Thank for posting! Q: when the scrubbers are frozen does the vacuum cleaner make a sound or does it seem like it wont even turn on? I'm having an issue where mine wont come on. I understand it could be the motor, the pump or the switch (or even a fuse link at the switch) but I was curious as to how what it did when the scrubbers locked up. Thanks
New bearings packed with marine grease. Just put that grease on all metal parts. Just clean-out old lubrication first. Any way to get the top bearing out?
What in particular are you looking for? The bearings? If it doesn't suck anymore but still runs, check the gaskets on the tank. It operates using negative pressure so a leak in the system wouldn't allow for it to suck up any water.
Mine recently just stopped workin and I barely had it for a year. I had turned it on and turned it off really quick, I don’t know if that played a factor for it not to turn on again. I was wondering if you know how I could fix it? I did plug it in properly and checked fuse or breaker in my own home. However, I haven’t checked checked it there’s a fuse in cleaner that was blown, I don’t exactly know where the fuse is lol. I’d like to save it as I spent almost $200 on it
Anybody have 'NO POWER' on HOOVER POWERDASH-PET carpet cleaner? It worked fine the last time i used it (6-7mos ago) now..... no power when red step switch depressed.. 😕 ???
I had the same issue, and i fixed it.. open it up and lift up the on/off switch body and press on on with your finger and if it works your problem is that the on/off switch body was not secured and was pushed up enough till the pedal could not reach it, what i did to fix it i put two pieces of plastic wire/string from a weed eater as a spacer on the right side of the switch body and made sure the clip on the left was holding the switch body
Oof! I always end up with more parts than when I start with! Could it be a spring for the power button or on the arm that connects between the back the damper on that vortex chamber?
My bruahes don't spin and the engine sounds louder than usual. Also noticed a burning smell; would this be due tot his same issue? Haven't opened it yet? Any advise would be great. Thannks in advance!
One possible cause is an air leak. If the unit freely spins check to see if you have airflow flowing through it. Also make sure the unit does spin. A frozen bearing will sieze the unit up. Check your gasket in your collection tank and the sealing gaskets under the tank
My brushes still don't spin. I checked and greased the bearings, the motor puts out great air. The filters are clean, the gasket near the body of the machine (near the top of the waste water tank seals. Still does not spin. what else can I check? ?gasket to hand held spinner? Is there another gasket somewhere for the air to escape before it gets to the spinner?
While I appreciate the time you took to make the video, your fast forward method didn't show me where to find all the screws. The last one which took the long handled screwdriver was hard to find as you said. Wound up breaking the thing while looking for it. Now, it is a goner.
Without opening it up, maybe run it for a few extra minutes on a dry patch of carpet to pull the moisture away from the bearings. Remember you'll have to tilt the arm down to get the brushes to spin and open up that mechanism. If you were to open it, you could hit the bearings with something that provides a moisture barrier. Something like wd40
The brushes won't stay in the housing. Nothing LOOKS broken, driving me insane. Please help , what am I doing wrong?.......Took them out too clean, now they look brand new falling in every direction as soon as I let go. Help
Oh no! Does the switch click when you press it? If it doesn't, it may not be lined up with the plastic on/off peddle. If it does click, the switch may be bad or the connections may be loose or broken. That's where I'd start. I hope this helps!
I used mine, cut it off went to cut it back on snd nothing. Then i tried a few weeks later cut it on, but i cut it off and now no piwer again. I can see the spring is still there. Please make videos of no power
@@Tturn1977if it randomly cuts on and off more than likely it's a bad switch. I'd recommend pulling the switch and actuating it by hand and see if you get a good positive click. A replacement switche should be reletivly inexpensive online
got mine in 2019 and could tell it was total junk then ...broke in 2022 ..this problem and the spray hose pump not spraying .... land fill its coming!!!
I tried and sadly the bearings in the turbine still lock up. I'm so tired of this issue every springtime that I've resorted to popping off the brush cartridge and using a 3/8 hex on the brush drive output socket. Mind you, the marine grease on the bearings saved me from having to use vise grips on the hex key to crack 'er free. But I just checked today and I did have to use the hex by hand still to crack it free. Shoddy design.
@@burlwilliams7661, more than likely you're okay if that's the case because frozen bearings will not allow movement. Remember these aren't belt driven brushes, so you'll have to run it on the floor to check for brush activation if in doubt they may not be operating properly.
You may have a bad switch, I'd recommend opening it up and actuating the button by hand (not with the plastic on/off button.) while unplugged! If it clicks, the problem could be the plastic butting isn't pushing the button down far enough, if it doesn't click, the switch is probably bad. A replacement should be cheap, look on the side of the switch and Google the part number.
If you're referring to the bearing in the black housing, I didn't replace it this go around. If I recall you unsnap the clips which exposes the impeller, you have to pull the impeller out and get access to the bearing that way.
So it shouldn't, I may have a bit of an air leak but as the unit only spins the bristles, it wouldn't be a critical leak and should still spin the bristles
Great video! Could you post where you sourced the bearings? The housing on my gearbox is cracked too bad, would ya happen to know where I can get it from? Couldn't find on eBay, thanks!
Thank you! I have done maintenance with the help of your video 2 years in a row. Great job. See you next year again :)
Nice job on the video! Have the same unit and noticed the brushes were not spinning. Disassembled and observed the bearings were completely frozen from rust. Soaked them in PB blaster and they freed up. Appreciate your help in the repair!
I bought the bearings on Amazon, $8.90. fixed! I almost gave up, figured it was shot. Seriously saved me $150. 🍻👍
How can I look up them exact bearing?
I followed what you did and it worked!!!!! I swear I was about to put it on the curb and get something else but I decided to give this a try and now I am back in business. If you are ever in the Boston area I owe you a beer or two or three!! Thanks so much.
Happy to help boss!
How to look up them berings? All I see on the internet is for roll brush bearing
Thank You!! nobody did a break down like you. This was the 3rd video I watched. trying to find the fuse.
I hope you found the fuse location!
@@handcraftedoverlanding I guess the motor was burned out. It’s under warranty so they don’t make parts for this anymore. I’m gonna replace for free the entire unit.
Me too! Did you find it?? If so can you tell me please?
@@VAcreeper my warranty covered a new unit because it’s inside the motor
@@ElusiveLabs damn-- ok, guess ima dig in the motor cause i dont have a warranty- I really appreciate the answer though-- thx bud!
Good video bro, question whats the brand of impact drill please?
I had an interesting problem with a Power Scrub / Spin Brush model... the handle would not pull hard enough to open the spray valve so no water came out. It is under the curved panel on the back side on the Power Scrub (where your knees would hit when your pushing it with the handle up) and found the valve. There was too much flex in the actuating rod from the water spray trigger/handle to push open the valve. I glued a small (1/2" square) piece of plastic I cut from an old storage container handle (about1/8" thick) to the actuating rod where it contacted the valve to make it just a tad longer and push harder so now works great !! Cost nothing!... Hope that helps someone.
My brushes won’t spin. I also cannot get water to come spray out. Do these go hand in hand ? I can’t find any issues with water flow like air in the line etc.
I am so thankful for you!!!! The only problem I had with my spinscrub was my chinchilla chewing through the cord. I found a new one on ezvacuum and was able to do a tear down thanks to your video. I could not find a SINGLE tutorial or any information at all on where the heck the cord wiring lives on the inside or how to get to it, but your video gave me the confidence to keep going and look for it myself. I figured, oh well, it's either keep looking and mess with this thing and throw it away, or throw it away, and buy a new one anyway. So after MUCH removal and even more teardown (I stupidly took zero pictures before continuing to rip everything apart) I finally found the compartment with the wiring!! Replaced it all on my own and after much guessing of how to get everything back, I was in tears when I turned it on and it was screaming at me after three sad years of it being dead 🥺😭 I am a 32 year old female and I'm just so proud that I was able to figure it out. Thank you for giving me the confidence and for showing the initial teardown!! I am so happy.
I'm so proud of you! You did a great job and sounds like you expanded your knowledge at the same time. It's amazing the strength and skills we have hidden until we take that leap and discover them! Great job!
I like how he says “arguably” as if people regularly contest his expertise on carpet cleaners.
Hahaha well I thought it was a neat design
Good video bro, question whats the brand of drill please ?
Rigid
I have to wonder....when you're done using the unit... if you put a fan to blow through the screen for a few hours so air blows through there and dries it out....this is what I've always done and my brushes haven't stopped spinning... Knock on wood. I really LOVE these cleaners they suck almost all the water back up....and are so easy to use and clean...I wish they made them better.
Hi, my extractor is SUPER loud. It sounds like jet engine. Any suggestions?
Thanks for posting this..Mine was one of the tubing was clogged up..
I have a similar carpet cleaner plugged in started it , engine sounded real weak then it cut out and I smelled a burning smell. Any ideas ??
Same
Awesome video
I can't get mine to spray water. Upper tank valve moving freely and I noticed tube going below bubbles move up and down when I squeeze trigger.
My nylon water pump impeller stripped. I 3D printed a new impeller and now I am good to go.
Thank for posting! Q: when the scrubbers are frozen does the vacuum cleaner make a sound or does it seem like it wont even turn on? I'm having an issue where mine wont come on. I understand it could be the motor, the pump or the switch (or even a fuse link at the switch) but I was curious as to how what it did when the scrubbers locked up. Thanks
Could you please link where you got the pieces please !!
Awesome! Thanks for this! Hey how about some strong velcro strips to keep in place?
If you had some heavy duty velcro I could see it working. Great suggestion!
New bearings packed with marine grease. Just put that grease on all metal parts. Just clean-out old lubrication first. Any way to get the top bearing out?
Hy , your video is so helpful…mine is 2yrs old it does not suctioning… would you please give me a link to buy it … I didn’t find it in stores
What in particular are you looking for? The bearings? If it doesn't suck anymore but still runs, check the gaskets on the tank. It operates using negative pressure so a leak in the system wouldn't allow for it to suck up any water.
Nice vid ! Yes they are totally repairable !
Mine recently just stopped workin and I barely had it for a year. I had turned it on and turned it off really quick, I don’t know if that played a factor for it not to turn on again. I was wondering if you know how I could fix it? I did plug it in properly and checked fuse or breaker in my own home. However, I haven’t checked checked it there’s a fuse in cleaner that was blown, I don’t exactly know where the fuse is lol. I’d like to save it as I spent almost $200 on it
Can you tell me where the fuse is on a Hoover carpet cleaner 50130
Anybody have 'NO POWER' on HOOVER POWERDASH-PET carpet cleaner? It worked fine the last time i used it (6-7mos ago) now..... no power when red step switch depressed.. 😕 ???
Same promblem, can't find any information on how to fix
Same! This is the 2nd one I have purchased and had the same issue with both
Same
I had the same issue, and i fixed it.. open it up and lift up the on/off switch body and press on on with your finger and if it works your problem is that the on/off switch body was not secured and was pushed up enough till the pedal could not reach it, what i did to fix it i put two pieces of plastic wire/string from a weed eater as a spacer on the right side of the switch body and made sure the clip on the left was holding the switch body
That’s exactly why I’m here.. smh
Hey I appreciate the vid but I have 2 springs the bigger one I figured out but the small one I have no idea where it came from
Oof! I always end up with more parts than when I start with! Could it be a spring for the power button or on the arm that connects between the back the damper on that vortex chamber?
My bruahes don't spin and the engine sounds louder than usual. Also noticed a burning smell; would this be due tot his same issue? Haven't opened it yet? Any advise would be great. Thannks in advance!
What other cause interferes with spinning and discharge
One possible cause is an air leak. If the unit freely spins check to see if you have airflow flowing through it. Also make sure the unit does spin. A frozen bearing will sieze the unit up. Check your gasket in your collection tank and the sealing gaskets under the tank
What is the bearing size? 4R/2rs is the seal type.
My brushes still don't spin. I checked and greased the bearings, the motor puts out great air. The filters are clean, the gasket near the body of the machine (near the top of the waste water tank seals. Still does not spin. what else can I check? ?gasket to hand held spinner? Is there another gasket somewhere for the air to escape before it gets to the spinner?
Mine won't come on at all hoover elite power scrub
What is a number part please
While I appreciate the time you took to make the video, your fast forward method didn't show me where to find all the screws. The last one which took the long handled screwdriver was hard to find as you said. Wound up breaking the thing while looking for it. Now, it is a goner.
Very helpful. It works.
Glad to hear it!
My shampooer quietly quit working with no burning smell what could it be
Mine is brand new. Glad to know how it works. Any suggestions for preventing the bearing problem?
Without opening it up, maybe run it for a few extra minutes on a dry patch of carpet to pull the moisture away from the bearings. Remember you'll have to tilt the arm down to get the brushes to spin and open up that mechanism. If you were to open it, you could hit the bearings with something that provides a moisture barrier. Something like wd40
Anyone know where the fuse is on this thing??
The brushes won't stay in the housing. Nothing LOOKS broken, driving me insane. Please help , what am I doing wrong?.......Took them out too clean, now they look brand new falling in every direction as soon as I let go. Help
Nice directions but would have been better if we could actually see what you were doing.
My power isn't coming on. There is no power to mine
Oh no! Does the switch click when you press it? If it doesn't, it may not be lined up with the plastic on/off peddle. If it does click, the switch may be bad or the connections may be loose or broken. That's where I'd start. I hope this helps!
I used mine, cut it off went to cut it back on snd nothing. Then i tried a few weeks later cut it on, but i cut it off and now no piwer again. I can see the spring is still there. Please make videos of no power
@@Tturn1977if it randomly cuts on and off more than likely it's a bad switch. I'd recommend pulling the switch and actuating it by hand and see if you get a good positive click. A replacement switche should be reletivly inexpensive online
I got my husband to straight wire mine, and works like a charm.
@@Tturn1977 Just plug it in and it's on? ;-)
got mine in 2019 and could tell it was total junk then ...broke in 2022 ..this problem and the spray hose pump not spraying .... land fill its coming!!!
I 3D printed a new water pump impeller. The original stripped out...
Similar repair for PET Elite model
Use marine grade grease youll never have to do it again most likely
That's a good option, a touch of grease never hurts.
I tried and sadly the bearings in the turbine still lock up. I'm so tired of this issue every springtime that I've resorted to popping off the brush cartridge and using a 3/8 hex on the brush drive output socket. Mind you, the marine grease on the bearings saved me from having to use vise grips on the hex key to crack 'er free. But I just checked today and I did have to use the hex by hand still to crack it free. Shoddy design.
If it spins at the hex key does that mean the bearings are spinning freely?
@@burlwilliams7661, more than likely you're okay if that's the case because frozen bearings will not allow movement. Remember these aren't belt driven brushes, so you'll have to run it on the floor to check for brush activation if in doubt they may not be operating properly.
Power won't come on
Anyone have to hold down the power button to keep it running
You may have a bad switch, I'd recommend opening it up and actuating the button by hand (not with the plastic on/off button.) while unplugged! If it clicks, the problem could be the plastic butting isn't pushing the button down far enough, if it doesn't click, the switch is probably bad. A replacement should be cheap, look on the side of the switch and Google the part number.
Don't just click it down and let go. Click it down and hold it there for a couple seconds, then it should work. Mine does that too.
HOOVER POWERDASH PET - MOD FH50700.
It was a waste of $140+ good dollars 💸
It’s all cracked on the inside. The plastic is cheap.
The saddest part is, it's still one of the, if not the highest rated carpet cleaners on the market
Yes, plastic is very cheap and poor quality. It basically crumbled as I took the thing apart.
Video was ok until you didnt show us how u removed the bearing by the white wheel
If you're referring to the bearing in the black housing, I didn't replace it this go around. If I recall you unsnap the clips which exposes the impeller, you have to pull the impeller out and get access to the bearing that way.
@@handcraftedoverlanding Two of my snaps broke off too. The screws went in fine though. Is it gonna leak now?
So it shouldn't, I may have a bit of an air leak but as the unit only spins the bristles, it wouldn't be a critical leak and should still spin the bristles
@@handcraftedoverlanding how were you able to pull the impeller out? I can't pull it out!
Great video! Could you post where you sourced the bearings? The housing on my gearbox is cracked too bad, would ya happen to know where I can get it from? Couldn't find on eBay, thanks!
Hey mine makes a horrible screaching sound, do you think its the motor?