Damm. All I need is smallest phillips screw driver and flat head screw driver. Just flip the key open and there is a small phillips screw , remove it then pry it open it with the flat head screw driver. I had it open less ten 30 second.🤣🤣🤣🤣
My RR had 2 out of 3 fobs not working needed a new battery. I was able to salvage both cases using curved needle-nose pliers stuck as far into the case with the key partially closed. Then I used tube extensions on the plier handles for mechanical advantage to open the original fob. No damage to the waterproof seal also use the ziploc bag trick for not losing parts. Thank you for the soldering tips
Hey thanks for the tip if I change out the battery will the key fob still work ? Some guy at O'Reilly's told me the truck wouldn't start if I changed the battery it would need to be programmed again
Здравствуйте. Подскажите пожалуйста у меня есть родной один единственный ключь старый , но на нем не работают кнопки, может сама плата вышла из строя в пультике. Вставляю ключь в замок зажигания, он проворачивает до конца, приборка горит но не чего не происходит. Чип в ключе есть. Может не запускается изза самой платы ключа? На кнопки нажимаешь-индикатор не горит на ключе и не чего не происходит
Agree, but it's not reusable and you'll need a new case regardless, so doesn't really matter. If you cut through all the way around it'll come apart more easily. Not an expert, but I've done two of them.
Nope, definitely not the right way to open the case!!! And he injured his finger! I can't believe someone would post this. There is a set screw that needs to be removed when you spring the key open and then it comes apart easily.
![[LIVE] : ONE ลุมพินี 76 | คู่เอก "ผึ้งหลวง vs สมิงดำ"](http://i.ytimg.com/vi/9SBshmGQOIM/mqdefault.jpg)
Damm. All I need is smallest phillips screw driver and flat head screw driver. Just flip the key open and there is a small phillips screw , remove it then pry it open it with the flat head screw driver. I had it open less ten 30 second.🤣🤣🤣🤣
The generic key fob has the small screw the factory one doesn't
My RR had 2 out of 3 fobs not working needed a new battery. I was able to salvage both cases using curved needle-nose pliers stuck as far into the case with the key partially closed. Then I used tube extensions on the plier handles for mechanical advantage to open the original fob. No damage to the waterproof seal also use the ziploc bag trick for not losing parts. Thank you for the soldering tips
Use solder wick and it will remove the solder....Look it up much easier and no chance of damage to the circuit board!!!!!!!!!!!!!!!!!!!!
All you need is a short blades pen knife, insert short edge of fob and gentle prize open. This is so destructive.
Hey thanks for the tip if I change out the battery will the key fob still work ? Some guy at O'Reilly's told me the truck wouldn't start if I changed the battery it would need to be programmed again
Здравствуйте. Подскажите пожалуйста у меня есть родной один единственный ключь старый , но на нем не работают кнопки, может сама плата вышла из строя в пультике. Вставляю ключь в замок зажигания, он проворачивает до конца, приборка горит но не чего не происходит. Чип в ключе есть. Может не запускается изза самой платы ключа? На кнопки нажимаешь-индикатор не горит на ключе и не чего не происходит
Do u have to reprogram the key in any way?
everyone needs to give this a thumbs down so that nobody on TH-cam sees this and does it this way
VL 2330 is the battery
where did you get the battery?
i opened the key cleaner than that, with just a pair of scissors!
Agree, but it's not reusable and you'll need a new case regardless, so doesn't really matter. If you cut through all the way around it'll come apart more easily. Not an expert, but I've done two of them.
LOL!
There's no need to destroy the old case for Gods sake
You didn't half butcher that fob case have a look at the right way to do it on other channels
Nope, definitely not the right way to open the case!!! And he injured his finger! I can't believe someone would post this. There is a set screw that needs to be removed when you spring the key open and then it comes apart easily.
The factory one doesn't have a set screw it needs to be cut open. The generic ones have the set screw