Well, thanks for explaining in-depth how to adjust our shafts, tightening springs above to get a wide opening in our warp and how to use the brake handle. My springs don't pop out but what happens to me is that my "brake" is very stiff and doesn't lift so easily. What have I done wrong when assembling. what I've been doing for past 2 months and off the bench, walk to side and lift brake handle and turn the dial to loosen back been and then use brake to advance.... Hope that's clear.
Thank you Dave and Pam! I love my Louet looms (I have 3 now) and these videos that you do to show how to make adjustments and WHY! I don’t know of any other looms that are so responsive to the weaver’s needs. Thanks for the info!
Very informative video. Thank you. I am getting ready to install my first warp on my new David 3. Really looking forward to weaving my first of many projects. Thank you for the great setup and a beautiful loom.
Would love to see a video like this for those of us who have a David II. I was not aware that most of this was possible and don't know what the similar targets would be for the David II.
The screws on the shed adjusters do not raise or lower my shafts. I finally held up the bars and noticed that even when the cords bowed on either side, the shafts did not move. I have been trying to fix the shedding problem all morning, but things are much worse than when I started. I weaved 4 plain weave towels and it worked beautifully. I tied up for twill...and its a mess. I cannot fix it...I tried everything.
Based on feedback from my customers, some people think they couldn’t beat hard enough. Also, you have to clean lint off the bar and the bushings that the bar goes through if you weave a lot with cotton. Some people found that annoying.
Unfortunately no, the beater on the new David will not fit on the old David loom. There are some articles to help with a David 2 beater that is not smooth. You can look up these articles at our website, www.louet.com or open a ticket and I can direct you to the articles
![หมานแต่ผัวเขา - แสตมป์ โตเกียวมิวสิค [ OFFICIAL MUSIC VIDEO ]](http://i.ytimg.com/vi/m0g1TSBJPgo/mqdefault.jpg)
![อยู่ได้แล้ว - LIPTA feat. Mirrr [OFFICIAL MV]](http://i.ytimg.com/vi/-9-hpntNym4/mqdefault.jpg)
I received my David loom in three flat boxes a few days ago. These videos are tremendously helpful with the assembly. Thanks!
Well, thanks for explaining in-depth how to adjust our shafts, tightening springs above to get a wide opening in our warp and how to use the brake handle. My springs don't pop out but what happens to me is that my "brake" is very stiff and doesn't lift so easily. What have I done wrong when assembling. what I've been doing for past 2 months and off the bench, walk to side and lift brake handle and turn the dial to loosen back been and then use brake to advance.... Hope that's clear.
Thank you Dave and Pam! I love my Louet looms (I have 3 now) and these videos that you do to show how to make adjustments and WHY! I don’t know of any other looms that are so responsive to the weaver’s needs. Thanks for the info!
Very informative video. Thank you.
I am getting ready to install my first warp on my new David 3.
Really looking forward to weaving my first of many projects.
Thank you for the great setup and a beautiful loom.
Very helpful video! I love this loom.
super nice to see the david 3!
Thank you so much for this great video. Very useful!
Very, very helpful. Thank you so much.
Would love to see a video like this for those of us who have a David II. I was not aware that most of this was possible and don't know what the similar targets would be for the David II.
The screws on the shed adjusters do not raise or lower my shafts. I finally held up the bars and noticed that even when the cords bowed on either side, the shafts did not move. I have been trying to fix the shedding problem all morning, but things are much worse than when I started. I weaved 4 plain weave towels and it worked beautifully. I tied up for twill...and its a mess. I cannot fix it...I tried everything.
Good demonstration if I need that loom how do I go about it
The sliding beater was so great. I have no idea why they would get rid of it.
Based on feedback from my customers, some people think they couldn’t beat hard enough. Also, you have to clean lint off the bar and the bushings that the bar goes through if you weave a lot with cotton. Some people found that annoying.
The sliding beater doesn't work smooth enough for me in my David can I get the beater like this and attach it to my loom?
Unfortunately no, the beater on the new David will not fit on the old David loom. There are some articles to help with a David 2 beater that is not smooth. You can look up these articles at our website, www.louet.com or open a ticket and I can direct you to the articles
@@LouetWorldwide how to open the ticket?
Will this video also apply to my David2 loom?
No, this video is specific for the David 3
@@LouetWorldwide where do I find any videos on the 2?
How about the David I? This video helped me understand a bit more about the mechanics of the David. Now how do make the adjustments on my David I?
How can I purchase a loom?
You can order from any Louet dealer. Find our dealer list in North America - www.louet.com - The rest of the world - www.louet.nl
Kan er info komen in de Nederlandse taal?
Ja dat is de bedoeling.