scooter pcx problem with starting by centrifugal.
ฝัง
- เผยแพร่เมื่อ 6 เม.ย. 2023
- a problem we encounter with scooters is centrifugal starting
1.if the plate has a high temperature, the fermuit could not turn it with the same movement when it starts suddenly or when it vibrates a lot, it comes from the plate. if the fermuits are watered with grease, then the problem is much bigger, the same problem is here in the end, everything they worked perfectly. as for the springs, 3 small ones, reduce their power at idle, the wheel moves without pressing the gas, the 1 big spring, when it has its power from 16 g balls, it is as if
it has 18 g. It plays a big role that the screws are genuine, good quality, otherwise it won't start easily, you can't tell easily if it is strained, the plate, the screws don't work like the brakes, for example, on the brakes, if the screws are not good, you have to press them what brake levers 2 or 3 times stronger to stop is what you want if the screws are good with a little pressure the brakes will brake so well that you will think you have disc brakes for what transmission of the scooter is the opposite if the screws are not good for example it will rotate 2000 revolutions to make the start the originals can with 600 revolutions so with 2000 revolutions the fermuit you will rub with the iron 1400 above the temperature 2 times higher than the temperature from which the fermuit starts to make a black surface where it is considered a burnt fermuit the burnt fuse will make a start 3500-4000 revolutions imagine in the summer in high temperature you are with +1 passenger and on an uphill the temperature escapes as a result the flywheel plate loses its hardness and is useless for garbage but the tragic mistake what most of us do will only change the pads (fermuit) i mean the plate has changed hardness after 5-6000 km the scooter on the start will start to shake (vibrations) this comes from what plate is in this part there are 2 small bearings and further inside are transmission bearings, they don't break easily, other trains are forced... When you see a platter that has passed high temperatures, it is good to change both platters and screws. I work the fermuit with a plate, so when starting the scooter from 0 to 7 kilometers, you rub the fermuit with a plate to make a smooth start, then a fermuit with a plate is made.
#centrifugal
#problem #scooterpcx
• test drive on honda pc... - ยานยนต์และพาหนะ
This is one of the most interesting, helpful and informative videos I've seen on these CVT transmissions. Many thanks for posting it. You have a new subscriber!
Hi Deltic happy new year welcome thank you and anything you need let me know!!!
i really like your job, the part where you re-heat treated the bellhousing was a great touch to it. nobody does that, truly good job. but as other people said, use blue grease on bearings, its the proper grease for that. thanks!!!
Hi Martin you are clearly very right, thank you for your kind words, but the grease, the ones I put in the aeron with oil, good oil, if I aerate with oil, it is the best and the blue one they write is very good but also the white grease I have tried is amazing!!
All..oks!!
You need to change the belt. It's loosen.
If it me, i bought all the CVT components set brand new but this is great content.
Yes!!
Chage clutch lining and belt center spring
Hi jjtzolofttv Of course not what I explain in the video, this is what I did.
Need to replace 02 gaskets and 02 orings in your pulley to prevent grease leak !😀
But yes!
Use grease with high melting point not normal grease, blue type valvoline made for electrical motor bearings
It's more diluted from the original though
@@MBPATENTSكم سعر الشحم الاصلي
أنا لا أعرف رخيصة على أي حال
good video... maybe look around for much better made clutch . this type of thing is where the makers cut costs on cheapo metal parts. where the springs go from new should maybe have asmall steel roller inside the hole then it would not wear out so fast.
Dont do burn outs on cvt as it will quickly overheat the clutch and belt
Yeah, I agree with you.
He just destroyed the transmission
I think you don't even have a clue why you're talking, I've done between then and now around 70,000 to 80,000 km and nothing has happened it will get another 100 thousand kilometers I believe the problem would be if it eats za where yes and will make the center baro Also only the Bearing would be damaged No i transmit☺️
You are doing well. Everyone has their own opinion and can express it freely!!!
You must Use high temp grease, 4 gram into pin lane, 6 gram inside center hole. Do not use more than 10 grams total.
Hi Heroher Tires and seals wear out and it doesn't need a lot of grease on the outside. Thank you!!!
You are better than the manufacturer
Thank you!!!
😂😂😂😂
7:35, no wonder your clutch bell shows signs of overheating. Why not just replace all parts with new, especially since a wheel lock-up at 90kph when something fails can have dire consequences.?
because I changed 2 bells new genuine and every 20.000 km I was facing problems this was coming from somewhere else the problem just now I found the solution and I am very happy since he fixed it a year to date I have done around 60-70.000 km and it doesn't bother me in the least it doesn't shake or tremble you have the start i am very happy now this is your opinion with a replacement new I think I got you covered
Perfekt Job 👍
Tanks sir very tsnkz and nice blog,,i follw your ,chanil
Earlsamm Thank you!!!
Terima kasih 👍
Pendukungmu dari Indonesia
Hi babahais thank you very much 😉
Change all the rear assembly, change the band and clean the front clutch, that makes the trick
Can I ask a question, When Im fully revving my scooter while overtaking it suddenly drops down its acceleration. What might be the cause of the problem? I already check my carburetor and cleaned my cvt.
Hi ASMR if your scooter revs high then it's the carburetor if your scooters revs low then that's your problem
m.th-cam.com/video/WxzDJVyHpJM/w-d-xo.html
Or
m.th-cam.com/video/tFoQiq9OpfI/w-d-xo.html
I once have that problem too but with fuel injected scooter. In my case it's Throttle positioning sensor malfunction. Change TPS and some calibration and it's good to go
Bruh, clean it properly. Disassemble all the parts in Pulley set and Torque Drive set. Use a CVT spray degreaser to easily remove the dirt. Use only high temp grease. Clean the CVT cover.
Ωραίος. Συνέχισε έτσι 😂
Σευχαριστώ Γωργαρα 😄
Hi! I have a Honda activa. 110cc. Any idea on performance upgrades?
Hi ahuCJ just remove the stops from the variatorm.th-cam.com/video/H1o8aWGsuzE/w-d-xo.html
@@MBPATENTS thanks will do it and update! Which country are you based in? I also need lighter rollers
Boa noite irmão me tira uma dúvida Eu tenho uma scuter Yamara jog 50 ja troquei os roelete e quando coloco ela na pista em alta velocidade ela trava o cvt e desliga vc pode me informar se correria com folga faz isso?
Hi mauri girls I have no idea what you are describing is it from currents or is it from coils is it from multiplier logically because high the coils usually did it on yamaha this all yamaha have this problem at high but
When starting the scoot at idle,should the rear wheal move a little or not ?
It's okay if it moves at 4km/hr, specially if the Clutch Lining is new. If it moves at 8km/hr or more than that, then you should clean and check your Clutch Spring, Center Spring, and Rubber Damper.
Hi Audio Normally at idle it shouldn't move but all scooters do this logically and normally the jaws have opened a bit just enough to turn what wheel if it is stationary it is better at idle and so there is no problem.
Good skill😊❤
Hi Anissyt thank you very much for your kind words i watched your videos and they are perfect all the videos keep it up well done!!
I see, You have grease on your bell, And your CVT crank case isn't clean either. Always clean the whole cvt, use degreaser to easily remove dirt/oil/grease. Your torque drive oild seal seams damage causing the grease from your torque drive to get thrown anywhere.
Hi jerbar In the past I didn't do it now that's why you come and this video to show that they should be crystal clear
My scooter has been vibrating alot in pick up slow moving, i have replaced all components like , Belt, variator roller, bushings, steel wheels, clutch shoe, but still vibrating what could be the reason? Thank you for you help.
Hi visan take a look at the complications, it can also come from the rubbers that the motor mounted on the frame and the tooth that holds the motor is from what plate and from the jaws, that's where it comes from
also the springs that hold the jaws if they are open for text constance to be matches open it starts shaking because they are not tight it starts from low see also the springs that hold so many matches
這個技術在台灣簡單得很幾乎80%的人都會做離合器片換掉然後看那個碗有沒有壞然後看皮帶大概就是這幾種
在这里，他们在车床上传递它，他们传递另一种金属，就像陶瓷一样，具有更好的传输能力，温度更低 和更好的性能 非常感谢😉
you should clean the cvt every at least 5000-6000km
Ahza Abdul Tanti
riding the brake 😂
Yes 😉!!
The clutch shoes one and the o rings in the sleeve / the sleeve itself need replacement
i don't know what you are telling me i show you via video and how it works also and the result you try it here and tell me
Ona kış lastiği tak birde asfalt da son hareketi yap o tekrar asla gaz verdiğinde patinaj yaptıramazsın. Zincirli motorsikletler gibi değil maxi scooterlar malesef
Hi serkano prensip olarak bir çeşit kauçuğumuz var.
Detalles de los químicos ?? Saludos
Petrol!
I am
groove the clutch bell and A harder clutch spring is the solution. 1200rpm clutch spring
Hi Sean happy new year soon I will upload a video on what damage a hard spring causes anyway for me it is not good the hard spring does a lot of damage to the transmission
Yes"
i just buy daytona part pnp all set 😂cause i don't have a tool like u,
Hi tananton sale right each one with what he has simple just showed another form there are many ways very right for what you are
You need to clean your CVT and oil and gear oil
you say it very correctly, but the two rubbers and the two seals that keep the oil from leaving the center need to be changed here and there, thank you!!
clutch wear much replace new one
Hi buffalong when I can and I make it work like new Why not
the variator closes before the clutch engages, use lighter rollers
the lighter balls have an insane pleasure which you have and consequences you have major damage everywhere from the plastics to the transmission
@@MBPATENTS yes but the performance decrease anyway if you need that for city stuff you did a great job 👍
Hi thestic Performance is improving and everything works great!!
Weight of roller down about 2 grams from the originally weight. cvt spring use 1500 rpm and you will get good acceleration...
Hi danifer it has nothing to do with what you see what the video does about the clutch it has nothing to do with the spring nor the balls.
kenapa begitu lucu melihat dia memperbaiki itu 😂😂😂😂
kamu harus membolongi mangkok kampas gandamu kalau kamu mau mendapatkan akselerasi yang lebih baik dan tidak gampang slip
😉
фейк в конце смачиваем плитку и колесо получаем результат на видео
Hi hannilok Я вас не понимаю насчет плитки, о которой вы говорите. Я не кладу плитку на пол, объясните мне, что вы не понимаете, чтобы я мог вам помочь!!!
I see, PCX is just a high maintainance scooter but most owners didn't know it's problems.
Hi Astrix look at the pcx is one of the best scooters the king of scooters in these cubics and I don't think it has any damage at all peripherally a little with the currents and the rest there is in practice with the other scooters it is the best scooter and with the least damage of all the others the scooters
@@MBPATENTSululluluuulul7 please pululululuuuuuu have luuill uuuullilpuluu phone 😮😮p😮😅pu7ippp
Türkiyedeki pcx modelinde arka fren tamamen kampana
Mutlu Noeller Honda pcx disc brake back DIY patent. - TH-cam m.th-cam.com/video/SGIdtLnRtwY/w-d-xo.html
Saranku ganti mtr AE
Ok. Thank you!!
Rolki za ciężkie są 🙃
Hi Dingos I think not, depending on how everyone sees it.
baru tau kalo mesin pcx mungil kaya vario
Hi guitoin yang spesifik yang saya punya adalah model PCX 150 2016 jaraknya mendekati satu juta kilometer dan kompresinya masih 11,3 setelah satu juta kilometer saya akan mengunggah video yang mengatakan apa yang telah saya ubah dan bagaimana motor ini bertahan dan tarikannya sekuat pcx!!!
Sankara Chetry
MBPATENTS
fake at the end we wet the tile and the wheel we get the result in the video
Hihannilok I don't understand you about more tiles you are talking about I don't install tiles on the floor explain to me what you don't understand so I can help you!!!
Just buy new clutch
Aktarma organları tamam düzeldi ancak motorun ölü
Da tako je ali nije ni motor vec karburator mu ne dobija vazduh dobar to ga zeza