I dropped a bottle of vinegar on the floor of my garage when I was rushing unloading groceries. When I went back to clean it up, the cement was like brand new where the vinegar spilled.
+J. A. Gillett Newton It always works. Give it more time. I cleaned out extremely corroded gas tanks to perfect gray-colored metal using vinegar. With one really bad gas tank it took 5 days , but it worked. It always works.
Ritchard posterior like I said, to counteract the effects of the vinegar. It will continue to eat into the metal unless a base is applied. When done rinsing with baking soda and water, then oil it to prevent rusting.
+Guitar Whores I agree. I'm actually wondering if the vinegar is eating the iron under the rust, causing it to come loose. The vinegar still looks clear, and when he rubs the rust it doesn't look like it is dissolving at all. I think we need some chemistry help from +Nile Red for this :)
bro..... Vinegar is acetic acid. Also, this is inorganic chemistry, not organic chemistry. Also, metals dissolve in low pH conditions, not just their oxides. Basic metal finishing processes require that metal finishing processes such as plating occur in low pH conditions so as to better dissolve the desired metal to be plated. The part needs to be brought back into a high pH condition after the finishing process so that the metal doesn't remain coated in a low-pH solution, which will continue to dissolve metals until saturated. Bro. The only reason leaving it for years has worked for the OP is that the solution first eventually reaches an equilibrium, and then the solution eventually gets washed away or removed by other means. It technically is best to expose metals to a higher pH solution after applying a low pH wash, even though the amount of metal that the vinegar would remove would be pretty minimal as just a spray wash.
just did this with 10 WWII Thompson magazines. They were just block of rust, non functioning. 48 hours in vinegar bath, the rust wiped off. disassembled them, cleaned them out, buffed them, and blued them. they worked perfectly. all 10 ran 30 rounds each, no hang ups. Vinegar works better than Naval Jelly or any other product.
+Juan Villa It dissolves the rust because of PH differnce, so could use lye or baking soda and just mix that with some water. If you want to use vinegar, there's a way to create a powder of it.
I just used vinegar and a green scotch bright pad (not very abrasive) to get the rust off my stainless steel grill. I can't believe how easy the rust came off. Worked perfect, thanks for the great video!
Best of all its non toxic.the best cleaner for washing walls too.fly poos and greasy film,nicotine.all the hard stuff just wipes off. Also only thing to really get rid of cats pee stink.also urine that has soaked into tile grout. Yay for white vinegar.make sure to dilute with water if using on carpet,then rinse off.
I cleaned up a Walker Turner Drill Press I was given using conventional methods such as wire wheels and scrubbers. I didn't even do a good job at it. Now you have me so convinced that this will work I am going to buy 5 gallons of this and take the drill press apart again to get the rest of the rust off, the wire wheels I have just might help in the removal after I let the parts sit for awhile. Wish me luck.
It worked pretty well. There are definitely more steps than just laying the part in the vinegar. You also have to wash the parts after the fact, and put them in a solution of Baking Soda and Water for around 10 minutes, then dry them off and use WD-40 or an oil that prevents rust and rub it all over the part.
I just did a big metal sign completely rusted on the back after 12 years outside, and coming through on the picture side on the front. I made a shallow bath using plastic on the long patio table. It worked great but I did it twice as the rust was very thick, the first time I left it overnight. It went back to metal and also stripped all the paint off the picture side which was what I wanted. It started to rust again once the vinegar was washed off so with the metal still wet I sprinkled a liberal coating of BICARB SODA all over, first one side then the other and it completely arrested the rust, I left it till dry then brushed it off. Amazing, best job I've ever seen.
Vinegar is acidic. Full strength won't hurt anything. CLR or The Works bathroom fixture cleaner works good too. I once brought a very rusted ratchet back to life with The Works. There are 3 steps. 1st soak your steel in acid to dissolve the rust, 2nd spray the metal with baking soda water to neutralize the acid and finally, spray the metal with WD-40 to displace any moisture so it doesn't rust again. You could even use acid from a dead car battery. Just don't forget to neutralize the acid after the rust is gone.
Van Alstyne just mix baking soda and water together in a plastic spray bottle. spray it on and let it fizz. Repeat until it doesn't fizz anymore. Don't forget to displace remaining miosture with WD-40.
c b wd.40 is to stay there for ever 'till the day you decide to paint the rusted part; otherwise it will come back again and much harcher than never. With wd.40 acid and water just fly away and cause no more rust . Use it immidiatelly after cleaning with water , vinegar , acid , brush ,,, mandatory.
@@CB-ep8mf I generously spray WD-40 on, let it sit a few minutes, then use a paper towel to rub it in, while simultaneously soaking up any excess. (You can't really have "too much" WD-40, it's just my preference.) If you have just a small spot of rust, WD-40 is also good by itself.
I really thought this was total BS, but I purchased a used 12-foot trailer and it was in pretty good shape except the fenders and rail were rusty in spots. I thought, "what the heck I'll give this a try and see what happens." I brush on 5% apple cider vinegar and kept it wet for about a half hour. Sure enough, the rust came off easily, nice and clean metal fenders appeared. Now I had to figure out a way to apply the vinegar to the rails and other fenders, I thought I might try using old towels and soaking them in vinegar and wrapping them around the infected areas. We'll see what happens.
I have been using vinegar as rust removal for many years. It is cheap , safe to handle and works very will. The trick is to mix with water 50 50 , ,submerge the rusty part in the solution and leave it for a week or 2. Pressure wash the defrosted part and paint. You have to give time to work. Good video bud, Thanks for sharing.
My grandfather passed away some years ago and he left behind many trinkets including a stainless steel pocket knife. It doesn't look too old however the hinges for the blade and other parts are badly rusted. I definitely have to test this out! If it works, I will do the same with the head of an old hammer I found buried in the backyard.
This has to be the most helpful of all the vinegar bath videos I've seen. I have a bunch of rusty metal washers that I want to clean up and recycle. Because I am recycling, I'm trying to not spend any money unless I have too, plus I just don't want to buy new washers when I have a jar full of so many sizes at my disposal. Vinegar is chemical free and something that works wonders on so many different things, so I'm really excited to try this. I know it might take some time, but you can't beat something that's laying around your kitchen!
+SteviiLove Lol nothing is chemical free..... Everythig has chemicals in it. Vinegars chemical formula is NaHCO3, meaning it's made of one sodium atom, one hydrogen atom, one carbon atom, and three oxygen atoms. Vinegar is a mixture of acetic acid and water. Dilute acetic acid is the chemical name for vinegar, and its chemical formula is CH3COOH. And it is mildly acidic which means it can be dangerous.
+byrysh Amazing how some people think they aren't using "chemicals" when they use something "natural". Someone didn't pay attention in chemistry class or took astrology as their science elective.
I used vinegar, worked well.. but I did notice surface rust appears (pretty quickly) so might want to paint or coat the metal asap to help prevent it rusty again.
He didn't say anything about using tap water. He used vinegar. After the vinegar rinse in distilled water and baking soda then use some sort of oil based thing to coat the metal as like diesel fuel, 50/1 fuel, gasoline, or WD-40 or something lol
WOW. My harley's tank inside was rusted out so the dealership said they would take care of it for $400 but shit, i could have just filled it up with vinegar and taken a sponge to the inside of it after watching this. Amazing!
Not a big surprise since vinegar knocks the bluing off a gun rather quickly which all bluing on a gun consists of is converted rust. Vinegar is a mild acid and gets rid of rust rather fast but is mild enough to not eat anything else away.
Thank you folks for the tips, I kept going with the videos and found a video where the straight vinegar eats at the metal a bit, and so I'm trying the baking soda & lemon and have left it overnight, and I'll get back to you all...
- today i cleaned the old table saw my dad had built in the 70ies. i took *vinegar essence* which is much stronger than vinegar - and yes it took away all the rust in a few minutes. i had it set for about 10 to 20 mins and then sanded by hand while wet - found that the 240 is still a bit too heavy but takes off the worst parts. the 400 paper is good for finishing after wiping away all the dirt i sanded again with some W40 used some 00 steel wool too to get deeper into the slot parts will do this on all other machines in the shop - works great !
Acid in the vinegar is a great tool. Stinking Carpets are cleaned with vinegar in the tank with/wo carpet soap. The acid kills bacteria. So, maybe the tetanus would be killed as well. Great Vid!
Is it ok to use full strength vinegar? I use full strength distilled vinegar to clean out coffee maker/ pot. we have a lot of hard water stains out here in the desert.
+syyenergy7 I'm thinking about all the tools I've thrown away now? I'll have to try this. Is it advisable not to use 100% vinegar or is there a specific reason to mix 50/50 with water?
Dilute Muriatic acid with water about 5/1 and in two days they will look new. Muriatic acid at Home Depot. Be sure to neutralize with baking soda, then wd 40
I've been using vinegar for some years and satisfied with result eventhough have to wait a few hours to let it does the job. I choose this methode among several other ways because it is easier, easy to find the stuff on every groceries with pretty much affordable price and the most safe methode compared with the others
i have a mower deck im using a 3m sanding wheel on to get most of the paint off with but i find some pitted areas that have rust in them that the wheel cant get into that this would work great for, also the bottom of the deck practically has no paint on it but it really has a lot of rust on it, problem is the deck is a lawn tractor deck and dont have anything big enough to fit it in, how well is spraying it compared to soaking it and also how long did you let that sit? I have soaked bolts in vinegar to clean rust.
This awesome! Any advise on how to do this on a heavily rusted/corroded knitting machine needle bed that is too big to be soaked? Thanks for showing this
I put rags around my kitchen fioricet and soak them with vinegar for hard water build up and i keep them wet. so you could drape vinegar soaked rags over items that cant be put in a bucket
I sometimes use vinegar and a dash of salt in a saucer to "clean" old dirty pennies. It amazes children (and some adults). No electrolysis is involved in that. They come out looking like new, but all I think happens is that the dirty/ oxidized surfaces are chemically altered to be clear. It may work differently with iron and steel, especially if there's no salt present.
We just used a heavy duty version of the Works that had 23% HCl. It was about $7 and ate through a quarter inch of rust in about 10 minuets. Its bubbles are hot and it causes chemical burns but if you use gloves in a well ventilated area it'll work really well.
My Refrigerator started pitting rust a month ago..I washed it with clorox now it has grown around the front..Is soaking a towel with vinegar mixture and duct taping it , then spraying every so often work?..I thought it was mold since it was growing. but after seeing pictures of pitted rust..it looked just like it. All I have is ACV so going to try it unless you have a better idea..Thanks so much for posting.
I've been an automotive technician for decades and have tried EVERY special chemical for rust removal, and they're all either crap or so caustic you don't want to have anything to do with them. Just up until recently I thought I had tried everything.... So I saw all this on here and had to clean a goldwing tank but as anyone knows they're horrible horrible horrible to remove so I decided what the heck. Let's try the vinegar.... I was lazy, and left the tank in the bike... Just used straight vinegar and no water and no salt. Left it for 24 hours... Drained it then sprayed pressurized scalding hot water and bizam! Clean as a whistle!!! neutralized it. Dried it. Fogged it with yamalube to keep it from flash rusting and is perfect and maybe took me an hour and a half to do.
Would this work on water pipes, copper & steel, that have been spilled with calcium chloride (snow melter) brine?! I mistakenly kept leftover snow melter in a closet that had water pipes and it turned into liquid and got on the pipes and they’ve turned green like the Statuenof Liberty. Am worried it would eat into the metal and cause them to burst bits been over a year
Masked of a small part of my car door that had rust, it's a pretty rust free car in general but the car door and trunk lid had some rust, worked nicely but it took some damned time because i had to regularly go outside to spray, what i found worked best is to just take a piece of cotton and soak it and then tape it or hold it on just lean a plank onto the soaked cotton ball or cloth or whathaveyou and it stays there keeping it wet.
Dude! I'm really glad I found this video I discovered your channel when I was looking for info on that spooky machine and now I see you are a jack of all trades ova here. Being from MA myself it's nice to hear a familiar accent. Thanks again!
Yep it worked a treat, chains look better than before I used them on the beach. Thanks for the video 👍. What’s something you can use from the pantry to keep m in a reasonable condition with out the rusty crap staining your hands.
+MrReasonablethinker he doesn't have a 50% acid solution. he has a 50% vinegar solution. Which is indeed very dilute.. 100 % ( or even 50% ) acetic acid would in fact be so strong that it would etch the metal as well as taking away the rust.
MrReasonablethinker Not only was it not a stupid question, it was such a smart one that it was over your head. The original dude thinks you have to add water to activate the acid or it won't work, the way you have to add 100% sulfuric acid to water to make it into an actual acid. They sell pure H2SO4 which is 100% sulfuric acid. It's a syrupy liquid. It doesn't do anything unless you add it to water. But the genius here thinks pure vinegar is the same way, he doesn't know that vinegar is already 95% water and thinks that adding more water to it activates it. Dumbass.
The problem with any acid on a metal is flash rusting once it dries! Gotta put something on the part right away; if you're going to paint you have to paint. If you're going to use the part by itself you've got to clean it off with borax dissolved in water, then put some WD40 on it or something to keep the moisture in the air from the metal. 'Warning you! I MAKE rust-remover products and this is the side of it that nobody wants to show!
Borax dissolved in normal water? What is the problem exactly? Is it the leftovers of the vinegar (just like the leftovers of normal water in electronics cause corrosion?) I am just curious, not correcting, me myself i don't know anything really, but wouldn't using 99,9% Isopropanol-Alkohol be effective to for that purpose? Maybe just to expensive... Or is it also about adding an additional layer of coat (for protection)? Is that what normal oil or WD40 are doing? I also don't really understand what "keep the moisture in the air from the metal" means,,quite a lot of questions but i'd be nice if you could answer just one :D
Jawash Asalan means : ' keep the moisture ( humidity ) OUT of the treated area [ the acid , the water , and other corrosive elements ] ... That is the job of wd.40. , or coocking-oil. Then ,,, Paint later on ; should you decide so.
So use 50%water 50% vinegar? Also would that hurt the shine on the metal? I need to clean a 1095 stainless steel blade. Any help would be appreciated. Thanks
Hi there , I tried the plain white vinegar to a metal outside lamp that was on our porch and it worked perfect! But what can I polish it with to retain its look? Any ideas I tried post a photo but no luck. Thanks again
sandra gaudio It really isn't. Adverse effects doesn't come into play unless you eat grams of it, and it doesn't start getting dangerous unless you eat tablespoons of powdered iron/iron oxides. Iron oxides are pretty unreactive at room temperature, and the particles are way too large to make their way into the bloodstream via the skin. Long term skin contact can lead to dry skin or even a rash, but it isn't very toxic at all. There are seriously toxic iron compounds though, but none of those are a part of rust.
Buick Regal That's because tetanus is caused by bacteria, that mostly is found in soil. The reason you need a tetanus shot after stepping on sharp rusty objects is that most of them are dirty, and the porous surface is very well suited for the bacteria that causes lockjaw.
Buick Regal What Ludwig Ekner said. If you suffer a puncture wound with an object that's been left outside, rusty or not, if you're not up on your tetnus shots, you need to get one *immediately*. Lockjaw is nothing to chance--it'll make you miserable for a long while.
Another interesting thing about vinegar even in the 10 grain commercial strength it is a food product. As food it does not require EPA tracking and accountability. It can be poured down the drain unlike other acids. It can be purchased in 55 gallon containers
I'm trying to figure out how to remove rust inside this air compressor tank. Can the rust be removed with rocking back and forth the tank? It's a huge / big good old 90 liter tank so shaking it like a motorcycle gas tank won't do.
SOUNDS GREAT! ANY SUGGESTIONS FOR USING THE VINEGAR ON A RUSTED WHITE METAL STORM DOOR? I DON'T FEEL LIKE REMOVING THE DOOR SO HOW CAN I USE YOUR TECHNIQUE?
Can i use it on my wife's face? I was thinking of a paste to apply as a facemask overnight x 2 - 3 days she'd be almost good as she was 25 yrs ago when we got married....😆
Good to know, Brought my newer Jeep Grand Cherokee to Florida near the ocean and in three months my nice rust free engine is rusted to shit everywhere. I have been freaking out. I just bought the thing this year.
In Holland the vinegar is watered down. It was one of the first things I noticed when I moved to Holland. They have cleaning vinegar in hardware stores. I know in the UK the vinegar was much stronger.
edit: is it safe to soak your rusty BBQ pieces in a plastic container filled with vinegar or will the vinegar eat the plastic? so is vinegar better than sandpaper and vegetables oil? or the baking soda method?
I dropped a bottle of vinegar on the floor of my garage when I was rushing unloading groceries. When I went back to clean it up, the cement was like brand new where the vinegar spilled.
Gotta love glass bottles! That was one of those blessings in disguise.
Did your spouse throw a fit and demand you do the rest of the garage floor?
inspiredmessenger I'll try it...hate when hubby changes the oil filter😥
I laughed way too hard at this
Same!
+J. A. Gillett Newton
It always works. Give it more time. I cleaned out extremely corroded gas tanks to perfect gray-colored metal using vinegar. With one really bad gas tank it took 5 days , but it worked. It always works.
VINEGAR will Clean a Rusty Gas Tank th-cam.com/video/Udn4BrKVlzw/w-d-xo.html
water rusts metal,
wrong, oxygen does
Do I have to take the tank off?
If you have a way to drain it real good, you could get away with leaving the tank in.
Good demo. Just a side note, it's a good idea to rinse in a base like baking soda and water after using vinegar to counteract the effects of the acid.
+Guitar Whores why?
Ritchard posterior like I said, to counteract the effects of the vinegar. It will continue to eat into the metal unless a base is applied. When done rinsing with baking soda and water, then oil it to prevent rusting.
+Guitar Whores I agree. I'm actually wondering if the vinegar is eating the iron under the rust, causing it to come loose. The vinegar still looks clear, and when he rubs the rust it doesn't look like it is dissolving at all. I think we need some chemistry help from +Nile Red for this :)
+Jeff Parks NO. You could leave the vinegar there for years. No problem.
bro.....
Vinegar is acetic acid.
Also, this is inorganic chemistry, not organic chemistry.
Also, metals dissolve in low pH conditions, not just their oxides. Basic metal finishing processes require that metal finishing processes such as plating occur in low pH conditions so as to better dissolve the desired metal to be plated. The part needs to be brought back into a high pH condition after the finishing process so that the metal doesn't remain coated in a low-pH solution, which will continue to dissolve metals until saturated.
Bro.
The only reason leaving it for years has worked for the OP is that the solution first eventually reaches an equilibrium, and then the solution eventually gets washed away or removed by other means. It technically is best to expose metals to a higher pH solution after applying a low pH wash, even though the amount of metal that the vinegar would remove would be pretty minimal as just a spray wash.
just did this with 10 WWII Thompson magazines. They were just block of rust, non functioning. 48 hours in vinegar bath, the rust wiped off. disassembled them, cleaned them out, buffed them, and blued them. they worked perfectly. all 10 ran 30 rounds each, no hang ups. Vinegar works better than Naval Jelly or any other product.
Loki Fults did you use water also? Or just vinegar ?
Great thanks! Now I convinced of soaking my Mosin Nagant in vinegar!
James M there is 80 ml. water in one litter vinagre.
Instructions unclear. Used vinegar as instructed... rust still tastes terrible.
lmbo!
Just add the same amount of a quality vegetable oil and add everything to a salad. Tastes much better. Oh, and have a beer (or 7).
..and spit out the metal before chewing commences :-)
allanGEE
p
wiener stuck in beer bottle. Wat now?
This is really cool, now how do I get my whole truck frame submerged.
Haha! I know right?
+Juan Villa Got a swimming pool? XD
maybe try creating a vinegar based paste or gel or oil?
+Juan Villa
It dissolves the rust because of PH differnce, so could use lye or baking soda and just mix that with some water. If you want to use vinegar, there's a way to create a powder of it.
alot of vinegar
Thank you! I bought a pool, filled it with vinegar and parked my truck in it. She's like new !!
I just used vinegar and a green scotch bright pad (not very abrasive) to get the rust off my stainless steel grill. I can't believe how easy the rust came off. Worked perfect, thanks for the great video!
How has it held up?
Best of all its non toxic.the best cleaner for washing walls too.fly poos and greasy film,nicotine.all the hard stuff just wipes off.
Also only thing to really get rid of cats pee stink.also urine that has soaked into tile grout. Yay for white vinegar.make sure to dilute with water if using on carpet,then rinse off.
Virginia Jones Y
I cleaned up a Walker Turner Drill Press I was given using conventional methods such as wire wheels and scrubbers. I didn't even do a good job at it. Now you have me so convinced that this will work I am going to buy 5 gallons of this and take the drill press apart again to get the rest of the rust off, the wire wheels I have just might help in the removal after I let the parts sit for awhile. Wish me luck.
+WolfBearMoon lol same did it work tho?
It worked pretty well. There are definitely more steps than just laying the part in the vinegar. You also have to wash the parts after the fact, and put them in a solution of Baking Soda and Water for around 10 minutes, then dry them off and use WD-40 or an oil that prevents rust and rub it all over the part.
+WolfBearMoon cool thanks for the tips! Im definitely gonna try this but first with some Allen wrenches before I use it on my drill press
That sounds like a good idea. I hope your restoration goes well. Good luck!
Surprised how easy that came off- and it was *pretty heavily rusted too* 😮
Vinegar works! My pickles are completely rust free
I just did a big metal sign completely rusted on the back after 12 years outside, and coming through on the picture side on the front. I made a shallow bath using plastic on the long patio table. It worked great but I did it twice as the rust was very thick, the first time I left it overnight. It went back to metal and also stripped all the paint off the picture side which was what I wanted. It started to rust again once the vinegar was washed off so with the metal still wet I sprinkled a liberal coating of BICARB SODA all over, first one side then the other and it completely arrested the rust, I left it till dry then brushed it off. Amazing, best job I've ever seen.
Vinegar is acidic. Full strength won't hurt anything. CLR or The Works bathroom fixture cleaner works good too. I once brought a very rusted ratchet back to life with The Works. There are 3 steps. 1st soak your steel in acid to dissolve the rust, 2nd spray the metal with baking soda water to neutralize the acid and finally, spray the metal with WD-40 to displace any moisture so it doesn't rust again. You could even use acid from a dead car battery. Just don't forget to neutralize the acid after the rust is gone.
I was wondering how to get the baking soda on. Thanks.
Van Alstyne just mix baking soda and water together in a plastic spray bottle. spray it on and let it fizz. Repeat until it doesn't fizz anymore. Don't forget to displace remaining miosture with WD-40.
At what point do you wash the WD-40 off? And how long do you have to keep the baking soda and water on there and a WD-40 on there?
c b wd.40 is to stay there for ever 'till the day you decide to paint the rusted part; otherwise it will come back again and much harcher than never. With wd.40 acid and water just fly away and cause no more rust . Use it immidiatelly after cleaning with water , vinegar , acid , brush ,,, mandatory.
@@CB-ep8mf I generously spray WD-40 on, let it sit a few minutes, then use a paper towel to rub it in, while simultaneously soaking up any excess. (You can't really have "too much" WD-40, it's just my preference.) If you have just a small spot of rust, WD-40 is also good by itself.
I am doing this right now with an old ratchet wine press. Can't see it working yet. Been soaking for a couple of hours.
I really thought this was total BS, but I purchased a used 12-foot trailer and it was in pretty good shape except the fenders and rail were rusty in spots. I thought, "what the heck I'll give this a try and see what happens." I brush on 5% apple cider vinegar and kept it wet for about a half hour. Sure enough, the rust came off easily, nice and clean metal fenders appeared. Now I had to figure out a way to apply the vinegar to the rails and other fenders, I thought I might try using old towels and soaking them in vinegar and wrapping them around the infected areas. We'll see what happens.
Well, what now?!
Did it work?
Sky High “”One long very long amount of time later””(French Accent)...!
Ya have RESPECT AND DONT BE SO JUDGEMENTAL BECAUSE HE PUT OUT A EXCELLENT VIDEO.
Yo has it worked now?
I have been using vinegar as rust removal for many years.
It is cheap , safe to handle and works very will.
The trick is to mix with water 50 50 , ,submerge the rusty part in the solution and leave it for a week or 2.
Pressure wash the defrosted part and paint.
You have to give time to work.
Good video bud,
Thanks for sharing.
My grandfather passed away some years ago and he left behind many trinkets including a stainless steel pocket knife. It doesn't look too old however the hinges for the blade and other parts are badly rusted. I definitely have to test this out! If it works, I will do the same with the head of an old hammer I found buried in the backyard.
did it work ?
Ian B33 ha
Yep it works. Learnt this from old ship builder. How did they stop rust on bolts and rivets? Heat and drop in oil. No fancy chemicals in them days
This has to be the most helpful of all the vinegar bath videos I've seen. I have a bunch of rusty metal washers that I want to clean up and recycle. Because I am recycling, I'm trying to not spend any money unless I have too, plus I just don't want to buy new washers when I have a jar full of so many sizes at my disposal. Vinegar is chemical free and something that works wonders on so many different things, so I'm really excited to try this. I know it might take some time, but you can't beat something that's laying around your kitchen!
+SteviiLove Lol nothing is chemical free..... Everythig has chemicals in it. Vinegars chemical formula is NaHCO3, meaning it's made of one sodium atom, one hydrogen atom, one carbon atom, and three oxygen atoms. Vinegar is a mixture of acetic acid and water. Dilute acetic acid is the chemical name for vinegar, and its chemical formula is CH3COOH. And it is mildly acidic which means it can be dangerous.
+byrysh Amazing how some people think they aren't using "chemicals" when they use something "natural". Someone didn't pay attention in chemistry class or took astrology as their science elective.
jockellis
LOL Just like alchemy is a good way to earn a living...
+jockellis Well, people have to learn sometime. This is why reading helpful comments is good.
+byrysh Your main point is right - everything has chemicals in it. But your first formula is not for vinegar, NaHCo3 is sodium bicarbonate.
You know what else vinegar is good for? French fries. I've noticed my french fries are always free of rust.
yeah its good
Oscar Groucho yeah man it really tastes good, cooking it in vinegar.
Make sure you put the vinegar on first so the salt sticks to the fries.
Oscar Groucho you went to Ocean city?
Lmao
Time to soak the ol Ford with Vinegar!
Lusterburn Haa! I thought the same thing! Bring on the Chicago winters! (ok, don't, but......lol)
Vinegar and baking soda in a spray bottle.
Not sure what it'd do to the paint though.
Vinegar and baking soda will neutralize each other.
syyenergy7 BUBBLES!!!
Lusterburn ha ,was just thinking how to get the top of my fenders on the 63 ford
Thanks! I tried this and it worked way beyond my expectations.
Saved some hopelessly rusty tools.
I used vinegar, worked well.. but I did notice surface rust appears (pretty quickly) so might want to paint or coat the metal asap to help prevent it rusty again.
+sypher0101
durp.. use distilled water... drinking water has shit in it..
chris tragedia Distilled water for what ?
tap water has shiz
in it.. distilled has nothing in it.. iron and such..
He didn't say anything about using tap water. He used vinegar. After the vinegar rinse in distilled water and baking soda then use some sort of oil based thing to coat the metal as like diesel fuel, 50/1 fuel, gasoline, or WD-40 or something lol
i've been using apple cider vinegar. it works excellent. no need to buy expensive stuff. vinegar works very very well - thx!
WOW. My harley's tank inside was rusted out so the dealership said they would take care of it for $400 but shit, i could have just filled it up with vinegar and taken a sponge to the inside of it after watching this. Amazing!
i'm heading out today to work this magic on some old rims. have you tried adding salt to the vinegar?
Not a big surprise since vinegar knocks the bluing off a gun rather quickly which all bluing on a gun consists of is converted rust.
Vinegar is a mild acid and gets rid of rust rather fast but is mild enough to not eat anything else away.
evilcowboy as i don't own a gun, it is a surprise to me. i've been using a wire brush without much luck.
Gun Blue paste is another acid as Vinegar.... is Selenious Acid... it corrodes the metal and it turns dark bluish color...
Thank you folks for the tips, I kept going with the videos and found a video where the straight vinegar eats at the metal a bit, and so I'm trying the baking soda & lemon and have left it overnight, and I'll get back to you all...
yeh, vinegar is the ultimate rust remover and it's super cheap but the best part is you don't need a $5000 bio-hazard suit to apply it...100% safe
Funny thing is if vinegar was bottled as a tank rust remover people would rave how good it was at removing rust lol.
someone would already have done that if it wasnt for that smell
Shhhhh don't steal my idea
drifter13 I'll just say it's vinegar scented
@@YTRINX genius
Alden Fox wtf this was a year ago
- today i cleaned the old table saw my dad had built in the 70ies.
i took *vinegar essence* which is much stronger than vinegar - and yes it took away all the rust in a few minutes.
i had it set for about 10 to 20 mins and then sanded by hand while wet - found that the 240 is still a bit too heavy but takes off the worst parts. the 400 paper is good for finishing
after wiping away all the dirt i sanded again with some W40
used some 00 steel wool too to get deeper into the slot parts
will do this on all other machines in the shop - works great !
Wow, Awesome. I am re-ferbishing an old wine barrel and this is working superbly on the metal rings. Thank you.
Drinking Game: Whenever he says "heavily rusted."
im drunk af now
Merely i livw thos gsmw 🍺🍻
Merely I told my brother and we got shitfaced
Oh hell yes
4 shots
Wow...I would NEVER have thought this would work and it's NON TOXIC!! Thanks.
I like your victorious laugh :) Well done!
Acid in the vinegar is a great tool. Stinking Carpets are cleaned with vinegar in the tank with/wo carpet soap. The acid kills bacteria. So, maybe the tetanus would be killed as well. Great Vid!
the people that disliked this are just salty because they have to rub it off and don't want to
Is it ok to use full strength vinegar? I use full strength distilled vinegar to clean out coffee maker/ pot. we have a lot of hard water stains out here in the desert.
When he scratched the rust to show how heavy it was I cringed
glad im not alone in this. Like when u scoop gravel up off concrete with a metal scoop shovel
Cutting drywall makes my hair stand up
Any type of brushing or sandpapering gives me goosebumps
redrabbit11 its pretty heavily rusted too
i like the taste of rusty spoons
Wow that works great. If you have just a little surface rust, wet a piece of aluminum foil and it will come right off.
+syyenergy7 I'm thinking about all the tools I've thrown away now? I'll have to try this. Is it advisable not to use 100% vinegar or is there a specific reason to mix 50/50 with water?
Dilute Muriatic acid with water about 5/1 and in two days they will look new. Muriatic acid at Home Depot. Be sure to neutralize with baking soda, then wd 40
Serioously? I have that here for my pool. I'm going to give it a shot, thanks!
how about put it in a spray bottle and applied it to under the car to remove rust, does it sound like a good idea?
Hmm, how would you go about getting rust off something to big to submerge? Soak a towel and wrap with plastic maybe?
I've been using vinegar for some years and satisfied with result eventhough have to wait a few hours to let it does the job. I choose this methode among several other ways because it is easier, easy to find the stuff on every groceries with pretty much affordable price and the most safe methode compared with the others
Apple Cider vinegar works better,. Especially for pitted metal, or molasses. Molasses takes longer though.
i have a mower deck im using a 3m sanding wheel on to get most of the paint off with but i find some pitted areas that have rust in them that the wheel cant get into that this would work great for, also the bottom of the deck practically has no paint on it but it really has a lot of rust on it, problem is the deck is a lawn tractor deck and dont have anything big enough to fit it in, how well is spraying it compared to soaking it and also how long did you let that sit? I have soaked bolts in vinegar to clean rust.
This awesome! Any advise on how to do this on a heavily rusted/corroded knitting machine needle bed that is too big to be soaked? Thanks for showing this
I put rags around my kitchen fioricet and soak them with vinegar for hard water build up and i keep them wet. so you could drape vinegar soaked rags over items that cant be put in a bucket
I sometimes use vinegar and a dash of salt in a saucer to "clean" old dirty pennies. It amazes children (and some adults).
No electrolysis is involved in that.
They come out looking like new, but all I think happens is that the dirty/ oxidized surfaces are chemically altered to be clear.
It may work differently with iron and steel, especially if there's no salt present.
wow i see why vinegar is also used for hygiene, its pretty affective!
We just used a heavy duty version of the Works that had 23% HCl. It was about $7 and ate through a quarter inch of rust in about 10 minuets. Its bubbles are hot and it causes chemical burns but if you use gloves in a well ventilated area it'll work really well.
Dude I love vinegar!! Its like THE most essential house shit ever.
My Refrigerator started pitting rust a month ago..I washed it with clorox now it has grown around the front..Is soaking a towel with vinegar mixture and duct taping it , then spraying every so often work?..I thought it was mold since it was growing. but after seeing pictures of pitted rust..it looked just like it. All I have is ACV so going to try it unless you have a better idea..Thanks so much for posting.
I’m gonna give it a try with my lifting chains which were used on the beach and got a lot of heavy rust onm.I’ll give you an update in a few days
Can i use the same formula on brake disc rotors ? 50/50 water and vinegar ? If yes, how much time it will require to keep it in the formula ? Thanks
I've been an automotive technician for decades and have tried EVERY special chemical for rust removal, and they're all either crap or so caustic you don't want to have anything to do with them. Just up until recently I thought I had tried everything.... So I saw all this on here and had to clean a goldwing tank but as anyone knows they're horrible horrible horrible to remove so I decided what the heck. Let's try the vinegar.... I was lazy, and left the tank in the bike... Just used straight vinegar and no water and no salt. Left it for 24 hours... Drained it then sprayed pressurized scalding hot water and bizam! Clean as a whistle!!! neutralized it. Dried it. Fogged it with yamalube to keep it from flash rusting and is perfect and maybe took me an hour and a half to do.
Yep, I cleaned several gas tanks this way. RedKote them after all the rust is removed and then they'll last forever.
Would this work on water pipes, copper & steel, that have been spilled with calcium chloride (snow melter) brine?! I mistakenly kept leftover snow melter in a closet that had water pipes and it turned into liquid and got on the pipes and they’ve turned green like the Statuenof Liberty. Am worried it would eat into the metal and cause them to burst bits been over a year
Masked of a small part of my car door that had rust, it's a pretty rust free car in general but the car door and trunk lid had some rust, worked nicely but it took some damned time because i had to regularly go outside to spray, what i found worked best is to just take a piece of cotton and soak it and then tape it or hold it on just lean a plank onto the soaked cotton ball or cloth or whathaveyou and it stays there keeping it wet.
+Ismail Dikajev haaa
+Ismail Dikajev lmfao!! good call!
Dude! I'm really glad I found this video I discovered your channel when I was looking for info on that spooky machine and now I see you are a jack of all trades ova here. Being from MA myself it's nice to hear a familiar accent. Thanks again!
I sanded and soaked a railroad spike and it's clean as silver
Yep it worked a treat, chains look better than before I used them on the beach. Thanks for the video 👍. What’s something you can use from the pantry to keep m in a reasonable condition with out the rusty crap staining your hands.
Woman mind: stand and scrub for minutes with all your effort
Man mind: whats the quickest way i can clean this thing with no effort
it really works!! i used sherry vinegar sea salt and baking powder, all rust gone with a little toothbrush scrub 👍
hahahah ""cooking pan" "cookie pan" whatever the hell you wanna all it" hashaha i love it !
I have heavily rusted outdoor metal furniture, will this work or does the product have to soak in the vinegar?
Very Nice, this is the method I use for all of my saw restorations
Cool, i wonder would the vinegar allow a tub of starch to set so you could turn into a gel.
You said 50% vinegar, that means you diluted the bottle 50%? Because vinegar in the bottle is only 5% acetic acid so you diluted it to 2.5%
+MrReasonablethinker he doesn't have a 50% acid solution. he has a 50% vinegar solution. Which is indeed very dilute.. 100 % ( or even 50% ) acetic acid would in fact be so strong that it would etch the metal as well as taking away the rust.
+Steve Whitsett btw after re reading your post, I believe we may be saying the same thing.
Vinegar is produced by bacteria. Anything too strong would kill the bacteria that made it.
MrReasonablethinker
Not only was it not a stupid question, it was such a smart one that it was over your head. The original dude thinks you have to add water to activate the acid or it won't work, the way you have to add 100% sulfuric acid to water to make it into an actual acid. They sell pure H2SO4 which is 100% sulfuric acid. It's a syrupy liquid. It doesn't do anything unless you add it to water. But the genius here thinks pure vinegar is the same way, he doesn't know that vinegar is already 95% water and thinks that adding more water to it activates it. Dumbass.
Steve Whitsett
You don't know whether 100% acetic acid will etch the metal. You're just making that up.
u just saved me spend hundreds on cleaning rust of my rims lovein it
The problem with any acid on a metal is flash rusting once it dries!
Gotta put something on the part right away; if you're going to paint you have to paint. If you're going to use the part by itself you've got to clean it off with borax dissolved in water, then put some WD40 on it or something to keep the moisture in the air from the metal.
'Warning you! I MAKE rust-remover products and this is the side of it that nobody wants to show!
I use coconut oil on everything. Even mechanical parts. It works! I'm about to use it on my washing machine parts that are rusted. I LOVE vinegar!
ParadoxPerspective thanks
Borax dissolved in normal water? What is the problem exactly? Is it the leftovers of the vinegar (just like the leftovers of normal water in electronics cause corrosion?) I am just curious, not correcting, me myself i don't know anything really, but wouldn't using 99,9% Isopropanol-Alkohol be effective to for that purpose? Maybe just to expensive... Or is it also about adding an additional layer of coat (for protection)? Is that what normal oil or WD40 are doing?
I also don't really understand what "keep the moisture in the air from the metal" means,,quite a lot of questions but i'd be nice if you could answer just one :D
Jawash Asalan means : ' keep the moisture ( humidity ) OUT of the treated area [ the acid , the water , and other corrosive elements ] ... That is the job of wd.40. , or coocking-oil. Then ,,, Paint later on ; should you decide so.
old gregg YES : Deffinetlly.
So use 50%water 50% vinegar? Also would that hurt the shine on the metal? I need to clean a 1095 stainless steel blade. Any help would be appreciated. Thanks
Does this guy voice garfield?
sounds like it
From 'The Garfield Show'
Haha XD
No he is Ricky from the trailer park boys!!!!!
Hi there , I tried the plain white vinegar to a metal outside lamp that was on our porch and it worked perfect! But what can I polish it with to retain its look? Any ideas I tried post a photo but no luck. Thanks again
i live in England if it rained vinegar our rust problems would be sorted.
Trying this out on a small mid-century patio table that has seen better days and will, hopefully, soon be seeing some more...
dont use your fingers on rust like that again holy shit bro that wasnt a good idea use gloves rust is very toxic
sandra gaudio It really isn't. Adverse effects doesn't come into play unless you eat grams of it, and it doesn't start getting dangerous unless you eat tablespoons of powdered iron/iron oxides. Iron oxides are pretty unreactive at room temperature, and the particles are way too large to make their way into the bloodstream via the skin.
Long term skin contact can lead to dry skin or even a rash, but it isn't very toxic at all.
There are seriously toxic iron compounds though, but none of those are a part of rust.
oh ok
Buick Regal That's because tetanus is caused by bacteria, that mostly is found in soil. The reason you need a tetanus shot after stepping on sharp rusty objects is that most of them are dirty, and the porous surface is very well suited for the bacteria that causes lockjaw.
Buick Regal What Ludwig Ekner said.
If you suffer a puncture wound with an object that's been left outside, rusty or not, if you're not up on your tetnus shots, you need to get one *immediately*.
Lockjaw is nothing to chance--it'll make you miserable for a long while.
Oh crap the TH-cam doctor is here
Another interesting thing about vinegar even in the 10 grain commercial strength it is a food product. As food it does not require EPA tracking and accountability. It can be poured down the drain unlike other acids. It can be purchased in 55 gallon containers
"Cooking Pan, baking Pan, or whatever the hell you wanna call it" 😂😂😂😂
Viki grl I laughed at that too
Sweetie it's called a COOKIE SHEET. LOL. LISTEN TOO GRAMMA SHE KNOWS BEST.
Will these product harm the shine of my magnetic 410 quality sheet after removal of water stains? please reply fast
can I use vinegar to remove hemeroids from my ass
White vinegar only on that one!!! LOL
jjrimz99 try vinegar enema! Does wonders when constipated.
jjrimz99 test it ill watch the vid
Yes
jjrimz99 Apple Cider vinegar!...
I'm trying to figure out how to remove rust inside this air compressor tank.
Can the rust be removed with rocking back and forth the tank?
It's a huge / big good old 90 liter tank so shaking it like a motorcycle gas tank won't do.
Dont scrub it with your hand lol
SOUNDS GREAT! ANY SUGGESTIONS FOR USING THE VINEGAR ON A RUSTED WHITE METAL STORM DOOR? I DON'T FEEL LIKE REMOVING THE DOOR SO HOW CAN I USE YOUR TECHNIQUE?
Can i use it on my wife's face? I was thinking of a paste to apply as a facemask overnight x 2 - 3 days she'd be almost good as she was 25 yrs ago when we got married....😆
Hey guy how about you ,you still look the same as you were 25 years ago of course not she can say same thing about you too 👍👍👍👍👍👍
Ron Danino white knight
It's a joooooooooke
I suggest you try it on your face first to find out if it works Please get back to us with the outcome. 😂😂😂
Im going to try it for my favourite safety boots. Ive been thinking for a while on how to rust it off 😢 tq for sharing!! 💓💓💓
It does weaken it a little, but not much more than rust did. I use vinegar for everything it's awesome, just keep it away from rubber.
How can I use the vinegar/water to clean outdoor lighting fixtures?
How long is a "few" hours?
Sir I love you. I’ve been stressing about cleaning the rust off of my Briggs engine cover.
Good to know, Brought my newer Jeep Grand Cherokee to Florida near the ocean and in three months my nice rust free engine is rusted to shit everywhere. I have been freaking out. I just bought the thing this year.
Nice... What would vinegar do to the paint? I've got patches of small rust that I want to remove but keep the paint job.
Vinegar doesn't hurt the paint.
I need to do a science project and I need to know how many hours it takes more or less, it would be a great help if you could tell. Thanks
That's pretty cool! Rust is basic and vinegar is acidic so a neutralization reaction takes place right? Anyone know which salt is formed?
In Holland the vinegar is watered down. It was one of the first things I noticed when I moved to Holland. They have cleaning vinegar in hardware stores. I know in the UK the vinegar was much stronger.
we have an exterior door with rust on the bottom. could we soak a rag in vinegar and somehow attach it to the door? any ideas?
For rust on car roof would I soak towel in vinegar and leave on it?
edit: is it safe to soak your rusty BBQ pieces in a plastic container filled with vinegar or will the vinegar eat the plastic?
so is vinegar better than sandpaper and vegetables oil? or the baking soda method?
The vinegar will never eat the plastic. No problem at all to do that.
It works just takes time. Gotta make sure the part is free of grease or the vinegar won’t work it’s magic.
Can you use Apple Cider Vinegar as well? Or is it recommended to use the plain vinegar when it comes to removing rust stains on steel?
Thanks for the knowledge! Have a 71 K15 GMC longbed truck that is rusted like this sheet of metal in your video. Can't wait to try it today!
How would I go about it on a floor buffer machine that I can’t soak in vinegar
I want to remove rust from my washer using vinegar how long should i leave it in before draining vinegar out?