ไม่สามารถเล่นวิดีโอนี้
ขออภัยในความไม่สะดวก
Indesit dishwasher error codes and faults Flashing lights Diagnostic fault finding
ฝัง
- เผยแพร่เมื่อ 2 เม.ย. 2016
- Get your appliance fixed faster! Click the link below to browse our supplier's huge selection of appliance parts and support the channel at the same time! (repairpartstea...)
Tutorial: www.how-to-rep...
When your dishwasher doesn't work you normally get an error code, you may just think it has flashing lights but on most machines they mean something, these are called error codes and are designed in a way to help an engineer or you find the fault with the dishwasher.
This article is on Indesit which is made by the Merloni group, The fault codes may be similar. we have added a load of videos at the bottom to help you with your repairs when you work out the problem that you may have .
Dishwasher help videos
www.how-to-repa...
Please remember to subscribe to our channel
www.youtube.co...
Remember to Shop with www.how-to-repair.com and it would help us by posting the video or the website on your timeline. This helps us a lot and if we really helped you can always buy us a beer how-to-repair.c...
Please remember to mark us to your favourites also I would be grateful if you would subscribe to our channels social media as this really helps my site and keeps us going.
TH-cam. / apart4u
Facebook. / how.to.repair.appliances
F5 Fault code.
F5 is number 1 and 3 LEDs flashing and indicates, according to the manual your machine has a blocked filter. The reality is it may not be a blocked filter at all, as was the case with my machine. the filter was always perfect and rinsed out regularly. And it may not be any faulty components either - as was the case for my machine. The trigger for the code is a lack of pressure change at the low pressure switch. The low pressure switch is mounted on the side of the machine frame and connected to the wash chamber by a long rubber tube.
After turning on, the machine goes through a drain cycle pumping out any water/fluid that might be in the wash chamber before starting the initial fill. Then the drain pump stops and the solenoid opens to allow the machine to fill. My machine would drain, fill and then stop with LEDs 1 and 3 flashing. I could reset the machine and it would do the start up perfectly as above and get to the same point and stop. I removed the high pressure switch and low pressure switch and both were working fine. I applied air pressure to them and the electrical contacts closed. I put it back together and it still would not get beyond the end of the initial fill stage. There is one hell of a lot of unhelpful advice out there ! I wasted many, many hours.
On one site someone stated that they had observed the fitter remove the pressure switch and blow into the tube before charging him for a new switch. I pulled the pipe off the low pressure switch and did the same. The machine now works perfectly.
Obviously there was something modest blocking up the pipe. The machine had not been used for a couple of months before the failure so something must dried out and blocked the pipe. The pipe just traps a column of air. As the water level in the chamber rises, so it compresses the air trapped in the pipe. This very small change in pressure causes the switch to throw and informs the control system the wash chamber is now full to a suitable level. Doing the final repair, removing the pipe and blowing into it and then refiting it took me 3 minutes. F5 on the Hotpoint Indesit maintenance system is rarely mentioned and although I visited around 50 sites, the minority that did mention it all just referred to blocked filters. At one site a fitter advised that it could be a faulty pressure switch but did not help by advising which switch and how to identify it - so that is why I ended up testing both. how-2-repair.com do great videos but in the other video detailing all the fault codes they simply waltz passed the F5 and ignored the guy asking the question in the comments - what is it. So I am going to post up this comment in a couple of other places as well, so no one else has to waste quite as much of their life as me finding out they don't need to pay a fitter £70 call out for a new pressure switch when the fix is so easy.
Based on my experience today when there appears to be a partly blocked F05 senario. Don't know if it was slow drainage pipe (rather than blocked) and or a blockage of pipe to from pressure sensor but short period of sodium carbonate soak did not help but a long 2+ hour period has. Apparently the affected Indesit IDF125 needed a loak soak to remove the gunk causings its F05 problem.
Thanks for taking the time to post this. Sadly for me I came across this to late, spent all day on mine, got fed up and ordered a new dish washer, at least I have spares now 👍🍻
You are a life saver.... What a great person. I tried it and it worked perfectly. Thank you for helping others and righting this whole thing up.
Scrolling through those tech support forums and seeing useless "just look at the manual replies" was so annoying.
Do you have photos or know where I can find out what a low pressure switch or high pressure switch looks like?
All I can see is a water in and drain pipe out.
It took me 1 week, at least a hundred google searches and youtube videos and several dis- and reassembles of my dishwasher to find this comment. I spent 60 bucks because I already ordered a new drain pump, and I was almost ready to buy a new dishwasher. I was so frustrated... Thank you so much.
I gotta say, the fact that the F05 Error is so hidden or just straight up misleadingly described online, almost everywhere, should be considered a crime.
Again, thank you so much, Michael Evans.
Why was this in a minecraft hunt or hide playlist
Haha was looking for this comment
Might seem obvious to others but it just solved my issue. Had someone out recently who pulled out our dishwasher and when they put it back the clean water pipe got kinked and stopped drawing through water causing it to give lights 1 and 3 error. When I pulled the dishwasher out and no kinks ran fine so just taped pipe the wall to remove any risk of kinks and now runs perfectly.
Brilliant
Clear explanations on where to look.
Saves hours.
I repaired F05, please check the pressure switch and the inlet valve filter together. at the beginning I blowed the soft pipe on the pressure switch, and I confirmed that it works well, the alarm didn't disappear. also I cleaned the filter near the inlet valve, and then I found that filter was pushed too deep, it will press a rubber gasket behind and finally reduce the water flow because this wrong deep installation, so I pull out the plastic filter a little bit, the inlet flow immediately become stronger and faster, the alarm F05 also disappeared successfully.
Thank you for this video. I had fault F04 on Ariston LSE 610, it was thermostat, bought another one and know it's fixed. Thank you! Thermostat code C00041086, spare code 178260, 275489, 041086, NC78C. Cheers!
I'm glad we could help with your tumble dryerPlease remember to subscribe to our channelth-cam.com/users/Apart4u
Remember to Shop with www.how-to-repair.com and it would help us by posting the video or
website on your timeline. This helps us a lot and if we really helped you can
always buy us a beer how-to-repair.com/help/buy-paul-a-beer/
Please remember to mark us to your favourites also I would be grateful if you would
subscribe to our channels social media as this really helps my site and keeps
us going.TH-cam. th-cam.com/users/Apart4u
Facebook. facebook.com/how.to.repair.appliances
Great video. Definitely feel more confident getting to grips with my dishwasher. Just to confirm, I have an IDF125, and the LED layout is slightly different, with 3 in a row, them another up and to the right. I'm assuming the lone light is 4. In this case, I'm getting an F13 circuit board fault. I've opened it up and had a look, and there is no sign of disconnections, corrosion or obvious issues with the board.
The machine runs an initial cycle, and the error code comes on as it expels the first batch of used water, which (I left it in a bucket) runs freely out of the waste pipe (though I did notice it was cold. I don't know if this is normal for the first cycle). I'm probably going to buy a new board, but any advice would be appreciated.
Why is f05 skipped?
Hi. What about indesit di620 flashing 1 and 3. What the problem it shows? Thank you
I have the same, on/of and led 1 + 3 flashing, doesn’t say anywhere what this means
@@jaspermelchers me too???
Hi. Thanks for showing the error codes.
I have a Indesit DiF04B1 A+ Dish washer.
When I set it to a program. It starts to beep after about 1 minute. There are 4 lights flashing. Could you advise me of this code please. I have checked for blocked filter, topped up salt and rinse agent. Also for water eatery. Thanks.
Hi. I have a free standing indesit, which has a flashing 1st blue light. Checked all the pipes and everything looks OK. Is it the pressure sensor?
Many thanks!
hello,
can you help me? My dishwasher doesn't works and give a code errorbut i don't know exactly wath means. My diswasher model is a Indesit DFG 15B10 and the error code is: the pilots of "washing" an the pilot of "End" have a gren fix light, and the red salt pilot is blinking. what can be the problem? I want to repair by myself, how can i do? maybe is the thermostat?
thanks a lot!!!!
Great info very well explained. thanks
Very helpful thank you.
Glad it was helpful! @benmorris4825 please remember to subscribe to our channel as that really helps us th-cam.com/users/shortse432SAb2g08 Thanks, Paul 👍
Thank you for this video; I have Ariston dishwasher LFF 8H54 after operating for a while it displays A13 error. Can you help me out ?
what is the error light flashing 1-3 water is going to chamber but after that is out
You are a star. Thank you
Hi I have Indesit ids 105 and I have a flashing light just one 9k the left the washing light and I can't turn the machine off by using the power button
Very useful!
Thank you!
Very glad this video assisted you in your repair I hope it came across well enough for you to follow
Can anyone let me know how the LED's are numbered for the Error Code? Is LED No.1 the very left or very right one?
Hi I have an indesit dfg 15B1 it will start and can hear something going on but after about 2 minutes the salt light flashes constantly and the machine just stops. Please help 🥺
did you get a resolve to this?
I’m suffering the same issue - did you have any luck?
Hi, dif14b1 led power flashes, led eco on steadily. discharge pump on. the dishwasher is not switched off via a button.
what can it be?
How about slimline models? How to read error codes? bibs 3 times and flashes 5 times
I have an indesit idl 500 with the first light flashing, can I remove the flood sensor to solve the problem?
The 'sensor' consists of a lump of polystyrene that floats ..upwards..and a micro-switch (normally open); when pushed by the poly. the switch closes, hey presto flood detected. Worth checking wires are not damp (always unplug the machine).
Hi i have indesit dish washer model dfp5731 i have problems with A1 error
Hi @user-ri1nj9hs3z I will need the full model number of the identification plate and the details of your problem. Please use our contact us page and make sure you fill out the request for what your problem is. We will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/
Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks 👍
Key showing green thater
i own electrolux table top dish washer. i seldom use this washer. the selected mode ECO suddenly keeps blinking when the start switch is on. nothing works . please advise
Have you checked if there is any water in the base of the machine when I see the base I mean where the motor the pump is situated underneath where the plates go as you might have an antiflood device Switch @leongweifong1111 please remember to subscribe to our channel as that really helps us th-cam.com/users/shortse432SAb2g08 Thanks, Paul 👍
Mine is a DIF 14BI, sometimes it shows F03 and sometimes it shows F07... it can still start but will automatically shutdown and restart repeatedly... is it a system failure or water turbine problem?
Indiesit Idf 125 wash and end light flash. Fills ok heats ok and drains ok any ideas ..... Thank you
Every light is flashing on my machine & I can’t open the door to get my clothes out. Any idea’s without me smashing the door
I have a number 3 flashing light, I turn it on and it’s makes noise then when it should start to spray water it cuts out.
So you find what was the problem?
Thank you!
Hi, can you help please? My Indesit is showing F1 with orange flashing lights at either end of the control panel. It is aDSFC3M19S. It seems to be trying to pump out water that is not in there. It won't let me switch it off and having the door open does not stop it beeping. Thanks
it might be pumping out because an error is stopping the machine from working Thank you For leaving a comment this is for you th-cam.com/users/shortse432SAb2g08 please remember to subscribe as that's is what keeps this channel going. Thanks 👍
Did you ever solve this problem? I am having exactly the same issue. Thanks
Hi, my Indesit DSRL17B19 slimline freestanding dishwasher is stopping mid-wash before dropping the tablet (on eco), it stops with the play/pause light amber and the salt light blinking red rapidly.
The salt is topped up fully, as is the rinse aid. It seems to drain properly as after this fault the unit is not full of water (and neither is the bottom bit with the filters).
Unlike other larger dishwashers, this one has few LEDs for error codes.
The dishwasher is just a few months old, so it's still in warranty, but I wanted to see if there's any easy DIY fix (without having to take it apart).
what about the 05 code? can you identify this one?
Yeah me to, got a F5 (Not F05) error on the front of my Indesit DFP 584 model
F5 is number 1 and 3 LEDs flashing and indicates, according to the manual your machine has a blocked filter. The reality is it may not be a blocked filter at all, as was the case with my machine. the filter was always perfect and rinsed out regularly. And it may not be any faulty components either - as was the case for my machine. The trigger for the code is a lack of pressure change at the low pressure switch. The low pressure switch is mounted on the side of the machine frame and connected to the wash chamber by a long rubber tube.
After turning on, the machine goes through a drain cycle pumping out any water/fluid that might be in the wash chamber before starting the initial fill. Then the drain pump stops and the solenoid opens to allow the machine to fill. My machine would drain, fill and then stop with LEDs 1 and 3 flashing. I could reset the machine and it would do the start up perfectly as above and get to the same point and stop. I removed the high pressure switch and low pressure switch and both were working fine. I applied air pressure to them and the electrical contacts closed. I put it back together and it still would not get beyond the end of the initial fill stage. There is one hell of a lot of unhelpful advice out there ! I wasted many, many hours.
On one site someone stated that they had observed the fitter remove the pressure switch and blow into the tube before charging him for a new switch. I pulled the pipe off the low pressure switch and did the same. The machine now works perfectly.
Obviously there was something modest blocking up the pipe. The machine had not been used for a couple of months before the failure so something must dried out and blocked the pipe. The pipe just traps a column of air. As the water level in the chamber rises, so it compresses the air trapped in the pipe. This very small change in pressure causes the switch to throw and informs the control system the wash chamber is now full to a suitable level. Doing the final repair, removing the pipe and blowing into it and then refiting it took me 3 minutes. F5 on the Hotpoint Indesit maintenance system is rarely mentioned and although I visited around 50 sites, the minority that did mention it all just referred to blocked filters. At one site a fitter advised that it could be a faulty pressure switch but did not help by advising which switch and how to identify it - so that is why I ended up testing both. how-2-repair.com do great videos but in the other video detailing all the fault codes they simply waltz passed the F5 and ignored the guy asking the question in the comments - what is it. So I am going to post up this comment in a couple of other places as well, so no one else has to waste quite as much of their life as me finding out they don't need to pay a fitter £70 call out for a new pressure switch when the fix is so easy.
@@spindreams I Know it has been a while, but have you solved the issue ? I have the same machine
@@michaelevans9785 Confermo tutto quello che ha scritto Michael. Grazie grazie e bravo
My on and off button is flashing and the first and third light is on please help! Indesit dif04b1
That is fault code F05.
Check if cleaning the filter helps.
If not read the comment of Michael Evans.
Quale e i guasto quando lampeggiano il LED 1 e 3
Mine is giving me flashing lights on 1 and 3, anyone know what that is?
Hi haw are you Dishwashin error f5
You mentioned everything but F5
sorry for delay when you have a technical question please use our site for 24 hour response www.how-to-repair.com/help/contact-us/
Iam Glad we could help you. If you ever need help please use our site for 24 hour response www.how-to-repair.com/help/contact-us/
If have a question please use our site for 24 hour response www.how-to-repair.com/help/contact-us/
Please remember to subscribe to our channel
th-cam.com/users/Apart4u
Remember to Shop with www.how-to-repair.com and it would help us by posting the video or
website on your timeline. This helps us a lot and if we really helped you can
always buy us a beer how-to-repair.com/help/buy-paul-a-beer/
Please remember to mark us to your favourites also I would be grateful if you would
subscribe to our channels social media as this really helps my site and keeps
us going.
TH-cam. th-cam.com/users/Apart4u
Facebook. facebook.com/how.to.repair.appliances
I need this info also
For f12 how can i fix? Thanks!
Did you found? Idk what f12 mean
DPG15B1NXUK I have the wash light and end light lit green and the salt red light flashing please can you help me thanks in advance.
Hi, I will need the full model number of the identification plate and the details of your problem so that I can provide you with useful literature. Please use our contact us page and make sure you fill out the request for what your problem is. A video shoot of the problem would be perfect as well.
I will get back to you within 24 hours, normally. www.how-to-repair.com/help/contact-us/
Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍
@@How-to-repair Hello i sent my details on the website. I have a video of the fault and a picture of the machine model/serial number. I will email these through when you contact me. Much appreciated.
@@How-to-repair hello I sent my contact details on your website please can you reply to me so I can send the information. Thanks Paul much appreciated.
@@How-to-repair Hi Paul sent my details in to you from the website, please can you reply so i can send you a video and picture to help the fault finding. Thanks in advance.
Hi mate, I've created an FAQ page for you. You can find a detailed repair guide, and videos for your problem on this page. Here is the link: www.how-to-repair.com/faqs/indesit-dpg15b1nxuk-dishwasher-wont-start-washing/ 😇
Since we work very hard in our warehouse making free video guides for you all on appliances, we always appreciate a beer, offering a choice of single or round beer. www.how-to-repair.com/help/buy-paul-a-beer/
Please remember to subscribe to our channel, as that's what keeps this channel going. Thanks, Paul 👍
Dis 14 1 and 3 flashing.....what is the problem?
Defective pressure switch (poor switch contact), impermeable hose to pressure switch, the air trap at the bottom of the dishwasher is blocked by grease. Pressure switch located to the right under the side plate at the bottom of the frame
F04
No lamp flashing afhter pump he stop