Thank you for the video, I have a 2016 npr-hd with a u2202 code and limps at 55mph. I believe code is not communicating with DEF module. Any ideas? Reflash?
Hi ,very helpfull video , iam a mechanic and i have the same problem on a 2015 NRR ,I had a code for def injector with 3 codes on mimamori module just like you , injector code is gone but the 3 on mimamori wont erase and truck still on limp mode !!! Do you think it need reflashing ??
I had the same issue. If there are no codes, you can force the truck through a regen and it will automatically clear the derate and red exhaust system light. No need for a reflash most of the time. Edit: If it fails out of regen, the codes will come back.
Sir, how are you? I hope you are in good health. I have the same problem. Can I apply the same method via a scanner? K3 or otel scanner please help me and thank you
Hello, I have the same problem in my 2015 NQR. I saw this video and another video from you where you replaced a injector on the DPF. I don’t have the computer but the symptom is the same. I have the same lights on and the same beeping noise. What can I do??
My 2017 Hino 268A Is displaying the check engine light and also the SVS light sometimes. The truck looses speed and power when the SVS light comes on. Pienso es un problema electrico. Cual es tu opinion ? Podrias diagnosticar mi camion ? GRACIAS !!
@@truck_diagnostic tenemos tres camiones Hino que de ves en cuando tienen problemas, podemos llevarlos a tu lugar para diagnosticarlos y arreglarlos ? Cual es tu ubicacion ? O prefieres venir tu ? Nodotros estanos ubicados en Trenton Nj. Muchas gracias ! By the way we are sharing your videos with our colleagues that we work with at Amazon and other places.
YOU ARE GOOD!!! I changed one of the two NOX SENSOR which cost me $588.00 and the SVS light and problem went away, my truck is running strong again ! Also the check engine light went away after running the truck for about 400 miles. THANK YOU very much for your diagnose on my truck ! El ETERNO DIOS✨ te bendiga a traves de su hijo mi Señor JESUCRISTO✨
I have an 06 GMC T7500 with 7.8 Isuzu 6hk1. The truck would not rev up past 1000 rpm and it was the ecm. I took the ecm to a guy who has IDSS and he plugged it on a similar truck to test it and supposedly reprogram it. He said he did reprogram it but the ecm was the same. So, I had to buy a new one and the same guy programed it. This time I saw him do it. I installed the new ecm on my truck and it worked fine for a week but the problem has returned. No revving past 1000 rpm. The only thing in common that I have done is checked the injector contribution balance with a Launch x431 pad III scanner and coincidentally that's when the problems have happened to both ecms. The question now, do you think reprogramming the ecms it's all that may be needed and I shouldn't have had to buy a new one? And also, is the Launch scanner corrupting the program?
Well any reprogram with different than idds will damage the ecm like Water damage: Control Modules are loaded with electronic components and other sensitive parts; once it becomes wet, it can become inoperable. ... Corrosion due to age and weather: Over time, hot temperatures can cause key components of Control Modules to melt or even catch on fire.Corrosion due to age and weather: Over time, hot temperatures can cause key components of Control Modules to melt or even catch on fire.Power supply (simple as a ground or broken wire) could cause this. ECU could be fried by over voltage, reverse voltage etc. It's better to check any additional modules or scanner aftermarket is installed in the truck will cause the ecm to go bad before u putting new ecm check everything most likely u need new ecm but get the person who can deal with truck or simply buy new ecm and take the truck to the near dealer and get the right reprogram..
@@truck_diagnostic thanks for your prompt reply. No, I didn't try to reprogram with the Launch scanner, I was just checking the injectors with the enable and disable functions on the power contribution balance feature. After that the original ecm started not wanting to rev past 1000 rpm but all parameters checked ok. All three accelerator sensor voltages were normal, fuel rail pressure normal, cpk, cam sensor were fine. No codes on any other module. So, I took the ecm to this Isuzu guy who tried it on another truck and same thing was happening. He said he tried reflashing it with IDSS but no improvement ( I didn't see him do it) so he said the ecm is bad. I couldn't find a used one so I had to buy the new one ( $4350.00 ). So, I brought the new blank ecm to him and he programed in that other truck but he used my injector codes and entered my VIN #. I installed the new ecm and the truck drove without issues for 7 days until I went and checked the data stream and injector contribution wirh Launch scanner again and the new computer started doing the same thing again. I can't believe the ecm would fry and be able to start the truck but not rev up. At least there should be a dtc, don't you think? I have read online of 2 other cases same as mine but unfortunately, the guys who posted the problems did not give any conclusion of what had happened.
@@truck_diagnostic expensive, eh? By the way, I had the new ecm reprogrammed again and still the same issue. I have given it to the dealer which is going to send it to isuzu to be checked and hopefully replaced or repaired and perhaps they'll tell me what is failing so at least I have an idea of where to look on my truck. It's a real puzzle for there are no codes.
Wow very helpful, I have a truck in the same situation that someone cleared the codes. I'm going to try flashing the pcm tommorow, Thank you!
Maestro excelente video 👍
Thank you for the video, I have a 2016 npr-hd with a u2202 code and limps at 55mph. I believe code is not communicating with DEF module. Any ideas? Reflash?
Hi ,very helpfull video , iam a mechanic and i have the same problem on a 2015 NRR ,I had a code for def injector with 3 codes on mimamori module just like you , injector code is gone but the 3 on mimamori wont erase and truck still on limp mode !!! Do you think it need reflashing ??
Yes
I had the same issue. If there are no codes, you can force the truck through a regen and it will automatically clear the derate and red exhaust system light. No need for a reflash most of the time.
Edit: If it fails out of regen, the codes will come back.
Discupa en que estado estas tengo el mismo problema y estoy aqui en los Angeles
Thank you!!!!
Sir, how are you? I hope you are in good health. I have the same problem. Can I apply the same method via a scanner? K3 or otel scanner please help me and thank you
I believe can do but if u don't try u never know
@@truck_diagnostic
Sir, where is your work location? I am in America, in the state of California
@@truck_diagnostic
I need to do a reset ECU
Hello, I have the same problem in my 2015 NQR.
I saw this video and another video from you where you replaced a injector on the DPF.
I don’t have the computer but the symptom is the same.
I have the same lights on and the same beeping noise.
What can I do??
Well youu need computer or any mechanic near you
Because without codes u can't do nothing
Don't start guessing
Do you have to be linked to the internet for this?
Thank you
Not have a computer with that system. Need to know where speed control sensor is located at & what it looks like.
My 2017 Hino 268A Is displaying the check engine light and also the SVS light sometimes. The truck looses speed and power when the SVS light comes on. Pienso es un problema electrico.
Cual es tu opinion ? Podrias diagnosticar mi camion ? GRACIAS !!
No creo sea electrico puede ser el atc pipe pm sensor or nox sensors hay muchos factores lo eletrico se qda stable y te pone el problema alli
@@truck_diagnostic tenemos tres camiones Hino que de ves en cuando tienen problemas, podemos llevarlos a tu lugar para diagnosticarlos y arreglarlos ?
Cual es tu ubicacion ? O prefieres venir tu ?
Nodotros estanos ubicados en Trenton Nj.
Muchas gracias ! By the way we are sharing your videos with our colleagues that we work with at Amazon and other places.
@@ochoavlogs5633 dm on Instagram
YOU ARE GOOD!!! I changed one of the two NOX SENSOR which cost me $588.00 and the SVS light and problem went away, my truck is running strong again ! Also the check engine light went away after running the truck for about 400 miles.
THANK YOU very much for your diagnose on my truck ! El ETERNO DIOS✨ te bendiga a traves de su hijo mi Señor JESUCRISTO✨
Where is located, is there anyway to delete def system
Where are you located?
How much was it to reflags the computer at dealership
I need your help where are you located
Is this the only solution after issues are fixed?
Most likely
Even after clearing codes the light doesn’t turn off? That’s what idss is supposed to do
Yes
tengo exactamente el mismo problema. cuando dices hay que arriesgar cual seria el peor escenario si no salen bien las cosas
5mph vas a correr
I have an 06 GMC T7500 with 7.8 Isuzu 6hk1. The truck would not rev up past 1000 rpm and it was the ecm. I took the ecm to a guy who has IDSS and he plugged it on a similar truck to test it and supposedly reprogram it. He said he did reprogram it but the ecm was the same. So, I had to buy a new one and the same guy programed it. This time I saw him do it. I installed the new ecm on my truck and it worked fine for a week but the problem has returned. No revving past 1000 rpm. The only thing in common that I have done is checked the injector contribution balance with a Launch x431 pad III scanner and coincidentally that's when the problems have happened to both ecms.
The question now, do you think reprogramming the ecms it's all that may be needed and I shouldn't have had to buy a new one? And also, is the Launch scanner corrupting the program?
Well any reprogram with different than idds will damage the ecm like
Water damage: Control Modules are loaded with electronic components and other sensitive parts; once it becomes wet, it can become inoperable. ...
Corrosion due to age and weather: Over time, hot temperatures can cause key components of Control Modules to melt or even catch on fire.Corrosion due to age and weather: Over time, hot temperatures can cause key components of Control Modules to melt or even catch on fire.Power supply (simple as a ground or broken wire) could cause this. ECU could be fried by over voltage, reverse voltage etc.
It's better to check any additional modules or scanner aftermarket is installed in the truck will cause the ecm to go bad before u putting new ecm check everything most likely u need new ecm but get the person who can deal with truck or simply buy new ecm and take the truck to the near dealer and get the right reprogram..
@@truck_diagnostic thanks for your prompt reply.
No, I didn't try to reprogram with the Launch scanner, I was just checking the injectors with the enable and disable functions on the power contribution balance feature. After that the original ecm started not wanting to rev past 1000 rpm but all parameters checked ok. All three accelerator sensor voltages were normal, fuel rail pressure normal, cpk, cam sensor were fine. No codes on any other module. So, I took the ecm to this Isuzu guy who tried it on another truck and same thing was happening. He said he tried reflashing it with IDSS but no improvement ( I didn't see him do it) so he said the ecm is bad. I couldn't find a used one so I had to buy the new one ( $4350.00 ). So, I brought the new blank ecm to him and he programed in that other truck but he used my injector codes and entered my VIN #. I installed the new ecm and the truck drove without issues for 7 days until I went and checked the data stream and injector contribution wirh Launch scanner again and the new computer started doing the same thing again. I can't believe the ecm would fry and be able to start the truck but not rev up. At least there should be a dtc, don't you think? I have read online of 2 other cases same as mine but unfortunately, the guys who posted the problems did not give any conclusion of what had happened.
@@truck_diagnostic by the way, is your IDSS from AliExpress?
@@aldovera3789 no sir its stright from isuzu
@@truck_diagnostic expensive, eh? By the way, I had the new ecm reprogrammed again and still the same issue. I have given it to the dealer which is going to send it to isuzu to be checked and hopefully replaced or repaired and perhaps they'll tell me what is failing so at least I have an idea of where to look on my truck. It's a real puzzle for there are no codes.
You just read and write, without replace ECM module?
Quisiera poder contactarte
Via instegram
Se ve que tu video enseña mucho, pero si deberías de cerrar la puerta, solo se oye el beep..
🫡🫡👽👍👍👍👍
El beep is the exhaust sytem protection
No la puerta
Very hard to understand what you are saying