Надо Артёму написать.что только красить надо и мыть двс ну и расходники менять. Голову не шлифовать и блок тоже. А коленвал тряпочкой протереть и собирать:))))))
Мотору до этой "капиталки" явно было лучше Когда крутишь только собранный КШМ газовым ключём и то еле, то явно что то не так Дык ещё масло в резьбы бугельей, естественно момент потеряется, так и затяжка гайковертом, хорошо хоть резьбы не порвало на блоке
Thank you for watching the video and subscribing to the channel. We are very happy to have so many viewers like you. We promise to work hard to not let you down
Переборка от Варвара! Замеров сделано НОЛЬ! Насколько подходят вкладыши и кольца, большой вопрос! Сборка жужалкой без динамометрических ключей, это вообще нонсенс.
Спасибо за просмотр и подписку на канал.В связи со сложными экономическими условиями у нас не хватает инструментов для работы,надеюсь вы понимаете.Будем учиться на опыте для следующего восстановления.
@@restorationproduct1718 Если хватило на "жужалку", то уж на динамометрический ключ должно хватить, он дешевле гайковёрта. Моменты затяжки можно найти в интернете, в телефоне.
I didn't see any measuring tools like a micrometer or any torque wrenches. You didn't even use a straight edge to check to see if the engine block was straight, nor did you check the cylinder head for the same. This engine will not last long.
You did a good job, the engine started and ran well. However, you seem to use the hard hammer a lot. In the whole clip it seems to be the star of the toolbox. Please use soft blow hammers, like plastic, rubber or brass ones. You don't want parts to distort, bend or break.
Thank you for watching our videos. In order to have good products and meaningful videos, we have to spend a lot of effort and money. Thank you for supporting us.
what did I see here? And actually nothing. he just changed the gaskets and piston rings and sliding bearings. where are the crankshaft measurements? I didn't even see a torque wrench. the cylinders are all stained, and it was definitely necessary to grind and honing, mill the cylinder block, dude, your head gasket burned out and the cylinder head also needs to be measured and machined, despite the fact that it is cast iron. It was necessary to change the pistons and piston pins. it's a diesel, heavy duty engine, you know?
Thank you for your honest feedback, due to economic conditions do not allow us to take advantage of everything, the result is that the machine is still running smoothly. thank you very much
Thank you for watching and subscribing to the channel. We tighten the screws with experience, we do not have enough money to buy a screw weighing device.
Спасибо что смотрите и подписываетесь на канал.В связи с тяжелыми экономическими условиями,инструментов восстановления пока не хватает,вы часто смотрите и делитесь,помогайте нам,чтобы у нас была мотивация развиваться дальше.
Nice Restoration and rebuild of that diesel engine! Well Done Mate!👍 good to see you replaced the necessary worn parts with new and I loved that you got all new gaskets for it as well.
Obrigado por assistir e se inscrever no canal. Estamos felizes em ter fãs como você. Prometemos trabalhar duro para ter bons produtos e vídeos significativos.
Thank you for watching and subscribing to the channel. Because the machine is too old, we don't know which country it was made in. We guessed that this machine came from Germany.
Next and urgent investment from the profits: get a set torque wrenches. Leave the painting till last, or cover machined surfaces. Do work more cleanly, and how about measurements? then decide on decking head/block, recut valveseats, grind valves or replace. Cheap replacing valve stem seals. Well there is more but not the worst backyard overhaul I have seen on You Tube.
That blue smoke usually means you’ve got substantial blow by. Oil is getting past the piston and into the combustion chamber. That oil is burned during combustion. Which is why checking the cylinder walls and having the bores machined properly is vital. If this isn’t done the rings will never seat properly, and as already mentioned results in blow by.
Thank you for watching and subscribing to the channel. We have a very damaged car engine. Don't know the make and age of the engine, hope you can share your experience with us. clear. thank you very much
Este video muestra perfectamente lo que no hay que hacer, no usan llaves dinamómetricas para el torque , pintan superficies rectificadas, no miden tolerancias, usan la amoladora angular para limpiar una superficie rectificada,no usan la herramienta adecuada para alisar los asientos de válvulas etc , en general un mal trabajo que va a hacer que ese motor se destruya solo
Gracias por mirar y suscribirse al canal. Debido a las difíciles condiciones económicas. Trabajamos completamente con la experiencia disponible. Estamos seguros de que la máquina funciona de manera muy eficiente.
He should never put oil in the oil filter by hand not good at all for the car always put in in the motor and let it fall to the bottom of the oil pan. Rick Henderson.
THANK YOU FOR WATCHING AND REGISTERING CHANNEL.Due to difficult ECONOMIC CONDITIONS WE ARE REALLY COMFORT RECOVERY BY EXPERIENCE. WE WILL BE EXPERIENCE FOR THE FOLLOWING SERVICE.
Надо Артёму написать.что только красить надо и мыть двс ну и расходники менять. Голову не шлифовать и блок тоже. А коленвал тряпочкой протереть и собирать:))))))
Благодарим вас за просмотр и отзыв. Мы обещаем сделать лучше, чтобы не разочаровать вас
Excelente...... video saludos desde Córdoba Argentina
Muchas gracias, tenemos muchos otros videos interesantes e interesantes para que prestes atención y veas.
Awsome restoration one that engine 👌 like brand new superb job
Thank you for watching and subscribing to the channel. We are happy to have an audience like you
perpaduan warna hitam merah kuningnya pas bgt, mantap
terima kasih teman baik.semoga anda beruntung
Fabulous work❤
Thank you for watching and subscribing to the channel. Wishing you all the best. Happy New Year
@@restorationproduct1718 thanks a lot. Can I get your whatsapp nmbr?
Watching idol from LUCKY J Fishing
👏👏Thank you for watching and subscribing to the channel
Great job! Thanks for posting
Thank you for watching and subscribing to the channel. We promise to do better to not disappoint our fans
Assembly lube will help the build process- and make the engine last longer. A torque wrench will help as well. Just saying.
Thank you for watching and subscribing to the channel. We will learn from the experience for the next recovery
my favorit kombinasi color in your engine ... Mantab...!!! salam from 🇲🇨
Thank you for watching and subscribing to the channel. We are happy to have an audience like you. We promise we will not let you down.
@@restorationproduct1718 where u from brother ..?
Реставрация неплохая, но лучше шатунные и коренные затягивать динамометрическим ключом и гбц тоже
Спасибо за ваши комментарии, смотрите наши следующие видео
Fantastic job. I am assuming that is a diesel engine. Thank you for posting.
an old diesel engine we worked very hard for many days, thank you very much
For his birthday someone needs to buy him a engine rotation hoist and a torque wrench 😂😂😂😂
Thank you very much, you are so funny 😁😁😁
Bonjour de. PARIS. 03 10 2024
Très bonne Restauration moteur remis à neuf Bravo à vous Bonne journée
ok bon ami
très beau boulot et bien présenté dans un environnement propre ce qui n'est pas toujours le cas ...
Merci d'avoir regardé et de vous être abonné à la chaîne. Nous sommes heureux d'avoir des fans comme vous.
Движка с завода 😅 ты просто отчаянный делаеш на удачу 😅 мои поздравления 👏
Большое спасибо. Пожалуйста, подпишитесь на наш канал, чтобы увидеть последние видео
Great job. Congratulations from Brazil.🇧🇷
Thank you for watching and subscribing to the channel. Your compliments are a great motivation for us to work better, thank you very much.
Awesome job on engine
Thank you for watching and subscribing to the channel 👏👏👏😃😃
Hi Captain!! I showed my friends. Bravo! This content amusing! Never tired of these. !
...and i'll tell you all abt it when i see you again...
Thank you very much.
Excelente trabalho !
Obrigado por assistir e se inscrever no Kenh. Estamos muito felizes e felizes por ter um público como você. Muito obrigado
How much torque on those rod and mains? All of it... Think we should line up the rod to the crank? Nah it will self clearance..
Thank you for watching. I really don't understand what you mean. I did my best with that engine and the results were beyond imagination.
4 uggaduggas
🤦♂️🤦♂️🤦♂️
@@restorationproduct1718 you have strange imagination.
Haha no assembly lube or torquing of bolts and no tolerance checks, back yard mechanical.
This was over the top, talented for sure
Thank you for watching and subscribing to the channel
The oil coming out of that turbo says enough 🤣🤣🤣🤣🤣🤣 freshly rebuild!
Thank you for watching and giving us feedback. We will learn from our experience for the next recovery
Мотору до этой "капиталки" явно было лучше
Когда крутишь только собранный КШМ газовым ключём и то еле, то явно что то не так
Дык ещё масло в резьбы бугельей, естественно момент потеряется, так и затяжка гайковертом, хорошо хоть резьбы не порвало на блоке
ок, спасибо, что смотрели и давали нам предложения, мы почерпнем много опыта для следующего восстановления
it would be great if you use torque wrench & plastic hammer...
Thank you for your feedback. We will learn a lot to get good and meaningful videos. Thank you very much.
Wow. First asian using new parts
Thank you for watching the video and subscribing to the channel. We are very happy to have so many viewers like you. We promise to work hard to not let you down
BRAVO, EXCELLENT JOB my friend...
Thank you very much, man.
Excellent 👍
Thank you for watching and subscribing to the channel. We are happy to have fans like you. Good luck to you.
Chào anh gioi quá 👍♥️
ok , cảm ơn e nhiều
Nice job with what you have to work with.
Thank you very much, please watch our next videos
J adore. Très bien, parfait
Merci beaucoup, nous avons de nombreuses vidéos intéressantes à regarder
Переборка от Варвара! Замеров сделано НОЛЬ! Насколько подходят вкладыши и кольца, большой вопрос! Сборка жужалкой без динамометрических ключей, это вообще нонсенс.
Спасибо за просмотр и подписку на канал.В связи со сложными экономическими условиями у нас не хватает инструментов для работы,надеюсь вы понимаете.Будем учиться на опыте для следующего восстановления.
@@restorationproduct1718 Если хватило на "жужалку", то уж на динамометрический ключ должно хватить, он дешевле гайковёрта. Моменты затяжки можно найти в интернете, в телефоне.
Never, ever run a turbocharged engine without an air filter on the in intake side
Thank you for watching and subscribing to the channel
I didn't see any measuring tools like a micrometer or any torque wrenches. You didn't even use a straight edge to check to see if the engine block was straight, nor did you check the cylinder head for the same. This engine will not last long.
Thank you for your advice. Due to difficult economic conditions.we work entirely with available experience. We will add specialized tools next time
good job
ok thank you for watching and subscribing to the channel
You Work is amazing bro
Thank you for watching and subscribing to the channel 👏👏👏
Well done.
Thank you for watching and subscribing to the channel
You did a good job, the engine started and ran well. However, you seem to use the hard hammer a lot. In the whole clip it seems to be the star of the toolbox. Please use soft blow hammers, like plastic, rubber or brass ones. You don't want parts to distort, bend or break.
ok thank you for watching and giving us suggestions.we promise to draw a lot of experience to produce good and meaningful videos
Bravo my friend, you have a lot of skills. I wish you success. It seems that these repairs are very expensive.
Thank you for watching our videos. In order to have good products and meaningful videos, we have to spend a lot of effort and money. Thank you for supporting us.
looks nice. I like the colors
thank you good friend. wish you good luck
what did I see here? And actually nothing. he just changed the gaskets and piston rings and sliding bearings. where are the crankshaft measurements? I didn't even see a torque wrench. the cylinders are all stained, and it was definitely necessary to grind and honing, mill the cylinder block, dude, your head gasket burned out and the cylinder head also needs to be measured and machined, despite the fact that it is cast iron. It was necessary to change the pistons and piston pins. it's a diesel, heavy duty engine, you know?
Thank you for your honest feedback, due to economic conditions do not allow us to take advantage of everything, the result is that the machine is still running smoothly. thank you very much
😊😊pp
U r evil
M
Đam mê làm rất ok❤❤😂😂
rất cảm ơn
Waw very good
Thank you for watching and subscribing to the channel 👏👏👏
@@restorationproduct1718 👍👍👍👍👍 thank you
Bravo monsieur
Merci d'avoir regardé et de vous être abonné à la chaîne
Maravilha de trabalho muito capricho 👏👏💥eu também desde criança que gosto de máquinas de tudo que tem motores, tá no meu sangue 🔩🔧🔧🔩👍🇧🇷🇧🇷
Obrigado de longe. Você e eu temos os mesmos interesses. Prazer em conhecê-lo
@@restorationproduct1718 e isso aí amigo tá no nosso sangue 👍 um feliz ano Novo pra você é família daqui do Brasil 💥💥👍🇧🇷🇧🇷
@@restorationproduct1718^中.T..
Так рождаются новые китайские моторы без пробега 👍
я думаю, вы думаете правильно. большое спасибо
Top video
👏👏👏👍👍👍
Cool job ( mechanic auto )
Thank you for watching and subscribing to the channel
مبدع
محرك سيارتي يحتاج صيانه
غدا ان شاء الله اذهب للميكانيكي
شكرا لكم على المشاهدة والاشتراك في القناة ونحن سعداء جدا وسعداء بوجود معجبين مثلكم شكرا جزيلا لكم.
Good
Thank you for watching and subscribing to the channel
это не ремонт не проточен коленвал .гильзы не менял,поршни старые и так далее,а деньги взял наверное как за капиталку.
Спасибо за просмотр. Мы делаем все возможное. Что мы все еще используем, мы сохраняем
excelente trabajoo saludos desde argentina papa
Gracias por ver y suscribirte al canal. Nos alegra tener una audiencia tan grande como tú. Muchas gracias.
20:50 No alignment shaft?
Thank you for watching and subscribing to the channel. We have the lid with both vertical alignment and the machine is working normally
superbe
Merci d'avoir regardé et de vous être abonné à la chaîne
Parabéns pelo serviço de primeira qualidade minha nota é 10 Brasil, 2023
Obrigado por assistir e se inscrever no canal, procuramos sempre completar o produto da forma mais bonita
amazing ✅️ 👏
👏👏😉😉👍👍
Nice vidio👍👍
👍👍Thank you for watching and subscribing to the channel👏👏
Nice Job!
How many work hours to do this restauration?
we work continuously for 1 month. invite bbanj to see the next parts of the project
Muito bom ótimo
👏👏👏Muito obrigado
We usually number the pistons,big ends caps, valves stuck to a piece of cardboard in their order.that usually help when re-assembling time comes...
Thank you for your honest feedback. We will learn from it for the next time to fix it
Good nies
Thank you for watching and subscribing to the channel
Nice job
👏👏Thank you for watching and subscribing to the channel😊😊
Great job, but no torque on those bolts
Thank you for watching and subscribing to the channel. We tighten the screws with experience, we do not have enough money to buy a screw weighing device.
"Is the motor rebuilt?"
"Yep I wire brushed it and put it back together with my impact"
This poor motor😅
😒😒🙌🙌
I totally agree on this . As a automotive and heavy duty mechanic, a torque wrench should be used with all critical components. I hope it lasts
WOW and you yes
👏👏😃😃
Làm đẹp mắt đấy nhưng ẩu quá bác
😜😜😜
Torquing everything thing down to "that'll do er"
Thank you for watching and subscribing to the channel 👍👍👏👏😉😉😃😃
I prefer the VGG method. Keep on tightening her up until you hear your C2 and C3 crack. Then finish her off with a couple cold snacks.
Làm tổng thế cái máy này giá bnhieu a
alo 0981782688
muito bom top
Obrigado por assistir e se inscrever no canal, ficamos felizes em ter um público como você.
Без динамометрического ключа 🤦
Спасибо что смотрите и подписываетесь на канал.В связи с тяжелыми экономическими условиями,инструментов восстановления пока не хватает,вы часто смотрите и делитесь,помогайте нам,чтобы у нас была мотивация развиваться дальше.
@@restorationproduct1718 Подписался на ваш канал.
Затягивать гайковертом 🤦
@@restorationproduct1718 Спасибо.Мелочь за кадром.
Ремонт агонь, что делал что нет
👏👏👏Спасибо за просмотр и подписку на канал
Nice Restoration and rebuild of that diesel engine! Well Done Mate!👍 good to see you replaced the necessary worn parts with new and I loved that you got all new gaskets for it as well.
Thank you for watching and subscribing to the channel. We always try to do our best to have good and meaningful videos
Sehr gut
Vielen Dank für das Zuschauen und Abonnieren des Kanals. Wir laden Sie ein, sich unsere Wiederherstellungsvideos anzusehen.
❤❤❤❤❤
Thank you for watching and subscribing to the channel.
Merece muito mais que um like .
Obrigado por assistir e se inscrever no canal. Estamos felizes em ter fãs como você. Prometemos trabalhar duro para ter bons produtos e vídeos significativos.
So why did you chuck a bag of dirt and saw dust over the engine?
the engine is left in waste for a long time, so it is very dusty. The engine of the construction material truck is also very dirty
@@restorationproduct1718 rubbish, no pun
😜😜😜😜😜
can you do a rebuld of a Yanmar 523cc 2 cilinder Engine ?
Thank you for watching and subscribing to the channel. We have a huge project coming up for you guys. There is no engine that I can't do.
OWN tightening tools You don't work to fit the crank and connecting rods correctly torque wrench
Thank you for watching our video.
A craftsman overhauls a truck engine with many flaws. We will draw a lot of experience for the next restoration.
Un video muy interesante 🤏😎, y que modelo del motor es el del video?😲
Gracias por ver y suscribirse al canal Video recuperación y reparación 1 motor de camión que transporta materiales de construcción está muy dañado
top !!!
👍👍👏👏😜😜😁😁😊😊
whate is the liquid are you using for ceaning the block
We use gasoline to wash away grease, then we paint, thank you very much
So nice,i'm a practicing mechnics and i need you help
Thank you for watching and subscribing to my channel. Please watch my videos carefully and you will see many surprises
👍👍👍
👏👏😉😉
หมู่ยาบ้าขมวยไก่ชนวยรถกระบะขอสีชนพู ถามตำรวจจะคนร้ายได้หมุดยาน
😢😢😢
Why all the fancy colored paint.
We always try our best to create the best products and videos
Que marca o fabricante es el motor?
Thank you for watching and subscribing to the channel. Because the machine is too old, we don't know which country it was made in. We guessed that this machine came from Germany.
No as usado dinamométrica para ciertos tornillos??? No creo que dure mucho ese motor
Ok, gracias. Debido a las malas condiciones económicas, no podemos permitirnos comprar el mejor equipo.
На 4216 похож)
😜😜👍👍👏👏
Коленвал нестоит крутить таким ключом, место сальника испортишь, а так всё чётко! 👍🇰🇿
Спасибо за просмотр и комментарий.Мы будем учиться на опыте для следующего восстановления
Next and urgent investment from the profits: get a set torque wrenches.
Leave the painting till last, or cover machined surfaces.
Do work more cleanly, and how about measurements? then decide on decking head/block, recut valveseats, grind valves or replace. Cheap replacing valve stem seals.
Well there is more but not the worst backyard overhaul I have seen on You Tube.
Thank you for your feedback. We promise to draw a lot of experience for the next restoration. Thank you very much.
Always have some to say.
i'm a repairman in cambodia
Hi, nice to meet you.
ممتاز جداً ، ولكن لماذا يظهر لون الدخان شبة الازرق ؟ 😢
ممتاز جداً ، ولكن لماذا يظهر لون الدخان شبة الازرق ؟
That blue smoke usually means you’ve got substantial blow by. Oil is getting past the piston and into the combustion chamber. That oil is burned during combustion. Which is why checking the cylinder walls and having the bores machined properly is vital. If this isn’t done the rings will never seat properly, and as already mentioned results in blow by.
OK!😊
👍👍👏👏😉😉
Looks like a isuzu engine either a c240 or a 4bc2 with a turbo. I cam be wrong though
Thank you for watching and subscribing to the channel. We have a very damaged car engine. Don't know the make and age of the engine, hope you can share your experience with us. clear. thank you very much
Where vietnam , good
Thank you for watching the video. I'm Vietnamese no matter where I work, I try to do my best thank you very much
What’s engine size, I know is diesel,
😜😜😜😜
Este video muestra perfectamente lo que no hay que hacer, no usan llaves dinamómetricas para el torque , pintan superficies rectificadas, no miden tolerancias, usan la amoladora angular para limpiar una superficie rectificada,no usan la herramienta adecuada para alisar los asientos de válvulas etc , en general un mal trabajo que va a hacer que ese motor se destruya solo
Gracias por mirar y suscribirse al canal. Debido a las difíciles condiciones económicas. Trabajamos completamente con la experiencia disponible. Estamos seguros de que la máquina funciona de manera muy eficiente.
He should never put oil in the oil filter by hand not good at all for the car always put in in the motor and let it fall to the bottom of the oil pan. Rick Henderson.
Thank you for your comments, we will learn from experience for next time, see you in the next videos
good job
👏👏👏👍👍👍
You probably don’t know how to use or own a torque wrench. I have not seen you use it on this video.
THANK YOU FOR WATCHING AND REGISTERING CHANNEL.Due to difficult ECONOMIC CONDITIONS WE ARE REALLY COMFORT RECOVERY BY EXPERIENCE. WE WILL BE EXPERIENCE FOR THE FOLLOWING SERVICE.
😮😮😮😮
👍👍👍😃😃