A Onefinity CNC Done Right..

This video overview covers a really well built Onefinity CNC from a past client. I feel it will give many of you some ideas to use for your own system.
If you have questions, require a consultation, or a quote please message me direct at [e-mail] or through my eBay store here www.ebay.com/s...
Here's the components used from me in Perry's build.
CNC VFD Cable 20ft 16/4 DS Flexion & HY Large White Connector Installed (his unit was fully built which I offer. Please message me if you would like a quote for one)
www.ebay.com/i...
Huan Yuang VFD Remote Tool Less Mount Kit For Digital Interface
www.ebay.com/i...
If you just require the cable I offer that as well.

[@brucejomms]

What a beautiful looking machine. Many hours have been put into getting it up to the current state. Kudos to Perry on a magnificent build. He should be very proud of this.

[@corvetteguy50]

Thank you for your support Bruce. I really appreciate it. Vince

[@raulirimias4810]

Good example of "neat and tidy" electronics and cable management CNC. Thank you for sharing,Vince. Salutations from France.

[@corvetteguy50]

Raul, thank you for your support. I really appreciate it. Vince

[@andyprice4696]

Very nicely done

[@corvetteguy50]

Andy, thank you for your support. I really appreciate it. Vince

[@kimstewart7656]

Great set up Perry!

[@corvetteguy50]

Thank you Kim, I'm sure he would appreciate that! Vince

[@CustomCraftedDesigns]

Nice

[@corvetteguy50]

Thank you sir for your support. I really appreciate it. Vince

[@davidjun4435]

Outstanding video. I’m sure you mentioned it in the video…what spindle specifically is he running? Thank you!

[@corvetteguy50]

Hey David, thank you for the support. I believe its a 2.2Kw water cooled unit. Have a great weekend!
Vince

[@davidjun4435]

@@corvetteguy50 Thank you! I was kind of thinking. Is it just one of the generic ones? What are your thoughts on the higher end spindles? Like a Mechatron. Thanks again!!

[@corvetteguy50]

All spindle's do the same thing, so as long as their bearings are quality the performance should be excellent. Durability of any spindle depends on many factors like is the shop properly climate controlled, how hard the unit is worked, ect. Thank you, and have a great weekend!
Vince

[@IceCreams62]

It is an Huanyang spindle

[@corvetteguy50]

Correct, thank you for your support. Vince

[@BigHWorks]

Very nice layout indeed. Thanks for sharing, I am in the midst of putting together a Onefinity and this is helpful. Just FYI, the 1F doesn't come with drag chain but many folks seem to add it. I am wondering how this layout deals with the X and Z stepper cables. Do they simply drag along the side of the left side of the table?

[@corvetteguy50]

Alan, thank you for your support, and sharing about the drag chain. Have a great weekend! Vince

[@TPuffTree]

I recently read that the drag chain isn’t recommended because of the low and high voltage power on the router and Z coiling cable will get interrupted and cause issues. You need to rotate router 180 I think? I’m sure I’m saying something incorrectly, just passing along knowledge I learned from someone else.

[@bubba6945]

@@TPuffTree their new elite odel comes with drag chain and better cables

[@rexgrant3297]

Hi Vince, I just reviewed your video and I'm wondering where the stepper drivers are located. Did he hang the control box under the table?

[@corvetteguy50]

Thank you for your support. I'm not sure where his controller is located. I personally like the controller to be located for ease of access. Thank you,
Vince