THANK YOU for not adding any music! Allows viewers to concentrate on what you are doing. Great stuff. I am learning more about BMW engineering by seeing these things. I'm surprised you didn't do more cleaning of the valves and intake chambers.
I wanted a more mechanical, raw videos, so I'm glad you liked it! I did some cleaning on the valves and the intake chambers, but I couldn't get to everything without a proper parts cleaner booth. It's been running pretty smooth so far, though!
@@1ROWDY35I think he mentioned it took $3k to rebuild. I am not sure but in $3k you would get an engine that’s at 300kms I think. Rebuild would be a brand new engine so yeah
Incredible video. I remember watching the individual parts and that was cool, but as someone that probably will never rebuild an engine, I watched this one all the way through and thoroughly enjoyed it.
Thanks for watching! I spent 30 days selling BMW N20 parts, *was it worth it*? th-cam.com/video/SNI85pw4_tk/w-d-xo.html If you'd like to see detailed video for each part, check out the *BMW N55 Engine Rebuild* playlist: th-cam.com/play/PLfGJyGAcNr7-J2rSmmcNcQIT0QIvi2jCL.html If you'd like to see how it all started, check out the *BMW 335i Project Car* playlist: th-cam.com/play/PLfGJyGAcNr78Xbwh-kwd90uoDwGM3qr57.html Parts used: amzn.to/3QTT1YT Tools used: amzn.to/3SXwywS
Done well do far except the bedplate sealant, the proper way is to install and torque the bedplate and then install the front and rear seals, then use the syringe and push the sealant through the channels in the side of the block
This was fantastic, I have a 2014 F34 with an N55 that I was figuring was going to be the first engine I tried to do some or most of the rebuild on myself. Now after watching it, there are some more special tools to add to the kit, but it wasn't that horribly threatening. Thans!
@@r6scrubs126 I'm only at 105k on my 2014 335ix GT. I don't have a garage right now either, this is a future plan for sure. There are plenty of resources to help you walk through it though. If you have the time, resources, and spot to do it, go for it. Obviously not wrenching 101 here though.
Always good when you watch someone and they say or write how hard to tight that bolts, for example head gasket or oil pump. Good work man well done 👍🏻 ✅
the damage on the crankshaft and It bearings should happened due a low oil pressure, did you check the cams? it should be damaged too. The work that you did was great. But you had to change the oil pump, the piston rings at least and check the cams....
Not sure why you didn't remove the pistons and clean them out of the cylinders so didn't deposit all of the crud into the compression ring grooves. Even if you weren't going to replace the rings, which would have been a good idea, it wouldn't have been much more work.
it's kinda funny that you had no reaction to literally huge bits of engine parts just littered in chunks in the beginning, but having an audible surprise to a part beins heavier than expected. What are those broken bits anyway? turbo chunks?
Nice job ! It's great to discover/learn more about our engine architecture. (here for me, injector seal replacement and installation. Never seen this before in any video) ) Why you didn't tackle some other weak points of the N55 during this rebuild ? Cost maybe ? I'm thinking about the water pump (more difficult to replace while the engine is installed in the car) And install a protective plate behind the harmonic pulley to prevent damages if the serpentine belt is escaping. Finally, what is your exhaust ? It's sounds so sweet to my hears. Love it.
I mainly did this to learn exactly how engines work and to challenge myself to see if could do it. The cost was definitely a factor as I ended up spending basically the same as it would cost to buy a used engine (although with 90k miles). The water pump was placed less than a year before I got this car, so figured there was no reason to spend $400. The protective plate; however, was something I wish I installed, but at the time I didn't know those existed :). The exhaust is COBB cat-back exhaust: th-cam.com/video/Ue_d8Y6-EZE/w-d-xo.html Thanks for watching!!
Thanks for the reply. Progress has slowed because my crankshaft would not turn well once torqued the bedplate. Machine shop has crankshaft and they say it is fine, I have identified 004 in of runout on the crank. Your crank was bent also right? How did you remedy this?
Great Video compilation. I actually watched all the actual videos, and used the material to rebuild my '11 x5 N55 engine. It spun a bearing, number 2 cylinder. I replaced the engine, with a newer model, but kept the bad engine and rebuilt it. Now i have a spare engine. 😎
How many miles did your old one have before this happened? Also, how much more expansive would it be to do some sort of block guard? While everything is open? (For future high Hp applications)
I had purchased a 2011 BMW 535i, with an N55 engine. The engine has rattlely noise when I start it, and scanner shows Camshaft Retard, Bank A & B error code. I've replaced VANOS Solenoid valves to no avail. I've just replaced spark plugs, and will be checking the timing chain. Hopefully these last two will at least provide an improvement to the engine.
@@brewyawn3394not good. I turned the engine manually when checking the timing chain. Put valve cover back on, engine oil etc, started the engine, cranks but won't start.
No need when installing aftermarket bearings. I tested using plastigage to make sure the bearings I got worked for my set up and it was bang in the middle, so basically perfect. Thanks for watching!
Great work Can you explain at beginning of the video. When you started to fit bearing so you had two sets of bearing Sounds like you check clearance than you took off bearing than installed different bearing again. Not sure if I made sense 👍🏻
For both main and rod bearings I used my new bearings with the old bolts to measure the gap and make sure the clearance was within spec using plastigage. I have a video on plastigage if you want to learn more. Once everything checked out, I put some assembly lube and using new bolts torqued everything to spec. Using new bolts is vital as these are stretch to yield bolts and if you use old bolts, you won't get correct torque figures. Hope that helps! Thanks for watching.
Great wotk... Just one question you prepared the whole engine but why you did not check and have a look on the other pistons and thier rings... Just replaced the the damaged one
Could you show or add / send a link to where you found all the torque specs please! I’m in the process of putting my engine / subframe back together and I can’t finde torque specs anywhere…. Thank you!
I just bought the same exact car but convertible and I just found out there’s oil leaks basically oil gets mix with the coolant I spent all the money on this car now I don’t know what to do. I feel like I wanna cry
Not that many special tools. You'll need a timing tool, injector tool and few other smaller items. I have a link in the description with stuff I bought for this project.
That’s the idea. If it’s done well, it’ll be almost like new. Obviously tolerances won’t be a as good as factory. In some cases, you can upgrade components along the way and make it even better than new. Thanks for watching!
Can you suggest where i can get a 2012 bmw 335i service repair manual? I also have an engine to rebuild here in my house. It’s so hard to find engine rebuilder in NC. Thank you much in advance
Hi ! Thank you for this awesome content ! Really enjoyed watching this ! Just wondering if I can get some more precision for mainly two moments : 1) around minute 10 => How did you chose that gap clearance ? (I mean why not larger or tighter eventually) 2) around 16'14" or some few moments you've used a torque wrench to tighten that long bolt then you kept tightening it with a circle paper with angle => is there any reason/recommandation for that extra tightening such I've seen that no extra strengh should be put on after the torque wrench click ? Sorry if those questions have already been asked but I didn't see them prior and for sure, thank you for the questions ! Cheers !🙌
angle torquing is simply a more precise way of measuring ... so its not off. 70nm would be something like double that by doing 360. gap clearance is chosen by piston manufacturer. read manual for proper end gap... most brands are a little different than stock.
Most of the bolts on this engine are torque-to-yield, which means they stretch as torque is applied. To make sure the 'stretch' is exactly as it should be, BMW says to use a torque wrench and tighten it to, let's say, 90 lb ft of torque and THEN add additional 90 degrees of rotation. This is what that tool is for, it allows you to add addition rotation of torque to the bolt.
@@SimpleCarGuy Oh, I understood the additional angular torque. I meant, just the actual bendy arm and gator clip on the angle indicator tool. Not sure of its purpose.
And, never use a power tool to wind down mains caps bolts! the same goes for cylinder head bolts, always do by hand, but check the bolt threads beforehand.
That measures the tolerances to make sure they are in spec. If the ‘squished’ plastigage is too thick or thin I wouldn’t proceed with the install and have to get different bearing etc.
Hi! Yes, it's possible. Depending on the model of the car, you may need to drop the subframe (it's like 8 bolts) if you want to do the timing chain at the same time and you'll have to remove the radiator fan and a few things on top of the engine to remove the valve cover. I go into a little bit of detail in the video on the timing chain: th-cam.com/video/-apNebfNCMA/w-d-xo.html Thanks for watching.
Ngl I wish I could do this myself, right now I got my 2010 535 seating in my garage with a bad engine. I prefer rebuilding it instead of buying a use sketchy engine online for $2,000… 🤦🏾 I’m having a hard time finding a shop that rebuild engines out here in the Lehigh valley Pa .
I don't do this as a job, I just did it to see if I can rebuild an engine. The second engine I bought was $300 as it had a spun bearing which required a full rebuild because the crankshaft was damaged. It's not really worth it to pay someone to rebuild it as it's cheaper to buy a used engine.
THANK YOU for not adding any music! Allows viewers to concentrate on what you are doing. Great stuff. I am learning more about BMW engineering by seeing these things. I'm surprised you didn't do more cleaning of the valves and intake chambers.
I wanted a more mechanical, raw videos, so I'm glad you liked it! I did some cleaning on the valves and the intake chambers, but I couldn't get to everything without a proper parts cleaner booth. It's been running pretty smooth so far, though!
Did it cost more to rebuild than just replacing with a spare motor
@@1ROWDY35I think he mentioned it took $3k to rebuild. I am not sure but in $3k you would get an engine that’s at 300kms I think. Rebuild would be a brand new engine so yeah
15:27 what tool is that?
@@Saywhatohno yea if your gunna rebuild may aswel forge the whole thing
Incredible video. I remember watching the individual parts and that was cool, but as someone that probably will never rebuild an engine, I watched this one all the way through and thoroughly enjoyed it.
Glad you enjoyed it!
So relaxing watching this.... better than 90% of the other craps on social media. Thanks!
Glad you enjoyed it! I like watching these kinds of videos myself so figured I give it a try.
Just realised it’s soothing to make you sleep when you can’t
Thanks for watching!
I spent 30 days selling BMW N20 parts, *was it worth it*? th-cam.com/video/SNI85pw4_tk/w-d-xo.html
If you'd like to see detailed video for each part, check out the *BMW N55 Engine Rebuild* playlist: th-cam.com/play/PLfGJyGAcNr7-J2rSmmcNcQIT0QIvi2jCL.html
If you'd like to see how it all started, check out the *BMW 335i Project Car* playlist: th-cam.com/play/PLfGJyGAcNr78Xbwh-kwd90uoDwGM3qr57.html
Parts used: amzn.to/3QTT1YT
Tools used: amzn.to/3SXwywS
is the parts list same for all N55 even on the F series?
Done well do far except the bedplate sealant, the proper way is to install and torque the bedplate and then install the front and rear seals, then use the syringe and push the sealant through the channels in the side of the block
This is car guy ASMR
This was fantastic, I have a 2014 F34 with an N55 that I was figuring was going to be the first engine I tried to do some or most of the rebuild on myself. Now after watching it, there are some more special tools to add to the kit, but it wasn't that horribly threatening. Thans!
Did you ever give this a try? I'm considering doing it for my N55 M2
@@r6scrubs126 I'm only at 105k on my 2014 335ix GT. I don't have a garage right now either, this is a future plan for sure. There are plenty of resources to help you walk through it though. If you have the time, resources, and spot to do it, go for it. Obviously not wrenching 101 here though.
Awesome video. My 2015 335 has a rattle after shredding a drive belt from a leaky oil filter housing! Wish I had the skills to rebuild myself too.
Every second of the video was so satisfying to watch, great job! Greetings from Switzerland!
Glad you enjoyed it!
Always good when you watch someone and they say or write how hard to tight that bolts, for example head gasket or oil pump. Good work man well done 👍🏻 ✅
What a cool video! Very impressed at your determination and bravery to do all this yourself!
Thank you so much!
It ain't brave if you know what you're doing. This guy is skilled, not so much brave
Thank you for uploading these helpful videos. Got my new used N55 motor in and resealed with new bearings following your instructions.
Great to hear! Thanks for watching!
Hope it was worth it the N55 sounds amazing 🎶
I really hope the mechanics at BMW are just as meticulous as you are at how precise everything needs to be on this engine
this was extremely satisfying to watch! I feel like I can undertake an N55 build myself now! (maybe) lol
Good luck! It’s a long process, but you learn a lot along the way
the damage on the crankshaft and It bearings should happened due a low oil pressure, did you check the cams? it should be damaged too. The work that you did was great. But you had to change the oil pump, the piston rings at least and check the cams....
Excellent video. Fascinating to watch.
What was the total cost in rebuilding the engine and roughly how many hours do you think it took you?
I swear people are allergic to answering the cost question... It almost never gets a response
@@deezelkaneyep I need an answer 😫
@@Hvac.tools_prob 15 to 2500 if not including labor
@@BmwMe-uh9synot for a Bmw it cost about 5,000 in Florida to rebuild the transmission and that’s way less hours and parts than rebuilding the motor.
I did it and after you count bolts and hardware plus the crank you are probably going to be around $2,000
Cant believe I watched the whole thing. If I had any knowledge of doing a rebuild I would
Not sure why you didn't remove the pistons and clean them out of the cylinders so didn't deposit all of the crud into the compression ring grooves. Even if you weren't going to replace the rings, which would have been a good idea, it wouldn't have been much more work.
I should have, but I was already feeling like I’m putting way too much time into this and honestly, I didn’t have anyone to tell me any better.
@@SimpleCarGuy Considering you got the job done without knowing that, you did very well!
it's kinda funny that you had no reaction to literally huge bits of engine parts just littered in chunks in the beginning, but having an audible surprise to a part beins heavier than expected. What are those broken bits anyway? turbo chunks?
A master in his own craft
Nice job !
It's great to discover/learn more about our engine architecture. (here for me, injector seal replacement and installation. Never seen this before in any video) )
Why you didn't tackle some other weak points of the N55 during this rebuild ? Cost maybe ?
I'm thinking about the water pump (more difficult to replace while the engine is installed in the car)
And install a protective plate behind the harmonic pulley to prevent damages if the serpentine belt is escaping.
Finally, what is your exhaust ? It's sounds so sweet to my hears. Love it.
I mainly did this to learn exactly how engines work and to challenge myself to see if could do it. The cost was definitely a factor as I ended up spending basically the same as it would cost to buy a used engine (although with 90k miles). The water pump was placed less than a year before I got this car, so figured there was no reason to spend $400. The protective plate; however, was something I wish I installed, but at the time I didn't know those existed :).
The exhaust is COBB cat-back exhaust:
th-cam.com/video/Ue_d8Y6-EZE/w-d-xo.html
Thanks for watching!!
This was like therapy
Dude wanted to say thanks got my n55 out today thanks for you help. Ps I am a certified mechanic so im used to wrenching and have tools
Glad I could help. Thanks for watching! How's the progress?
Thanks for the reply. Progress has slowed because my crankshaft would not turn well once torqued the bedplate. Machine shop has crankshaft and they say it is fine, I have identified 004 in of runout on the crank. Your crank was bent also right? How did you remedy this?
Świetny film dzięki niemu zdecydowałem się samodzielnie wymienić uszczelkę pokrywy zaworów w moim N54. Pozdrawiam z Polski
Wow. I wan to learn this to be able to fix my own car.
The video editing qnd the ASMR is awesome
Amazing video. Only thing id say is clean out your engines as much as possible before re assembly of anything
Great tip, thanks!
Great Video compilation. I actually watched all the actual videos, and used the material to rebuild my '11 x5 N55 engine. It spun a bearing, number 2 cylinder. I replaced the engine, with a newer model, but kept the bad engine and rebuilt it. Now i have a spare engine. 😎
How many miles did your old one have before this happened? Also, how much more expansive would it be to do some sort of block guard? While everything is open? (For future high Hp applications)
I had purchased a 2011 BMW 535i, with an N55 engine. The engine has rattlely noise when I start it, and scanner shows Camshaft Retard, Bank A & B error code. I've replaced VANOS Solenoid valves to no avail. I've just replaced spark plugs, and will be checking the timing chain. Hopefully these last two will at least provide an improvement to the engine.
Hows it been?
@@brewyawn3394not good. I turned the engine manually when checking the timing chain. Put valve cover back on, engine oil etc, started the engine, cranks but won't start.
Masterpiece.
Nice Video my friend.Greetings from Serbia.
Great video and well edited! Did you have to worry about the “color” of bearings or not because they were aftermarket?
no
No need when installing aftermarket bearings. I tested using plastigage to make sure the bearings I got worked for my set up and it was bang in the middle, so basically perfect. Thanks for watching!
So cool. Loved all the little sounds. What's the purpose of the red anodized cam sproket brace thing?
The exhuast sounds perfect.
That sets the timing of the engine. I’m aligning the camshafts to the crankshaft in the TDC position
@@SimpleCarGuy Excellent. Thanks!
better build quality than they do in BMW factory!
Lol, no.
Great work
Can you explain at beginning of the video. When you started to fit bearing so you had two sets of bearing
Sounds like you check clearance than you took off bearing than installed different bearing again.
Not sure if I made sense 👍🏻
For both main and rod bearings I used my new bearings with the old bolts to measure the gap and make sure the clearance was within spec using plastigage. I have a video on plastigage if you want to learn more. Once everything checked out, I put some assembly lube and using new bolts torqued everything to spec. Using new bolts is vital as these are stretch to yield bolts and if you use old bolts, you won't get correct torque figures.
Hope that helps! Thanks for watching.
@@SimpleCarGuy makes perfect sense 👍🏻
Thanks
incredible video, nice job showing all
Great wotk... Just one question you prepared the whole engine but why you did not check and have a look on the other pistons and thier rings... Just replaced the the damaged one
you did a great job on this
Awesome rebuild! to your knowledge, does the timing chain on these every go bad like on the N20?
Could you show or add / send a link to where you found all the torque specs please! I’m in the process of putting my engine / subframe back together and I can’t finde torque specs anywhere…. Thank you!
Great video! N55 is definitely a great engine and you tackle this is great to see.
I am wondering how long does it take in real time?
Hard to say, I did this over probably like 6-8 weeks for an hour or two after works a few times a week.
Good job bro!
I just bought the same exact car but convertible and I just found out there’s oil leaks basically oil gets mix with the coolant I spent all the money on this car now I don’t know what to do. I feel like I wanna cry
Nice rebuild! You probably figured it out, but on the video you did forget a piece when reinstalling the top injector brackets.
I’m working on same thing now. Thank you for the great hands on experience.
Thank you for documenting this and sharing with us.
Like your video a lot but what special tools do you need for the BMW when you re-build the engine thank you.
Not that many special tools. You'll need a timing tool, injector tool and few other smaller items. I have a link in the description with stuff I bought for this project.
Amazing job bro
Dumb question, but since he basically rebuilt almost everything and cleaned a majority or the build it. Is it like having a 0 Mileage engine?
That’s the idea. If it’s done well, it’ll be almost like new. Obviously tolerances won’t be a as good as factory.
In some cases, you can upgrade components along the way and make it even better than new.
Thanks for watching!
Great work!
Thanx for the video i subscribed your video is the best than others
Thanks for the sub and for watching
nice video and thank you for put this up
That was so satisfying, thank you
Amazing job!! Thanks for sharing.
Do you remeber the torque spec for the spark plug buckets/housing?
Can you suggest where i can get a 2012 bmw 335i service repair manual? I also have an engine to rebuild here in my house. It’s so hard to find engine rebuilder in NC. Thank you much in advance
How much does it cost to rebuild a engine I supposes it depends what parts need to be replaced, and where you live.
Hi ! Thank you for this awesome content ! Really enjoyed watching this !
Just wondering if I can get some more precision for mainly two moments :
1) around minute 10 => How did you chose that gap clearance ? (I mean why not larger or tighter eventually)
2) around 16'14" or some few moments you've used a torque wrench to tighten that long bolt then you kept tightening it with a circle paper with angle => is there any reason/recommandation for that extra tightening such I've seen that no extra strengh should be put on after the torque wrench click ?
Sorry if those questions have already been asked but I didn't see them prior and for sure, thank you for the questions !
Cheers !🙌
angle torquing is simply a more precise way of measuring ... so its not off. 70nm would be something like double that by doing 360. gap clearance is chosen by piston manufacturer. read manual for proper end gap... most brands are a little different than stock.
I have a n20 engine that has low compression cylinder 1-3-4 90 psi num2 119 can these engines be honed ?
Great video!
I have a question. Why u dont remove all pistons to check and clean?
What is the purpose of the clip and arm on the angle indicator? I checked your "tools used" link, but still didn't quite understand.
Most of the bolts on this engine are torque-to-yield, which means they stretch as torque is applied. To make sure the 'stretch' is exactly as it should be, BMW says to use a torque wrench and tighten it to, let's say, 90 lb ft of torque and THEN add additional 90 degrees of rotation. This is what that tool is for, it allows you to add addition rotation of torque to the bolt.
@@SimpleCarGuy Oh, I understood the additional angular torque. I meant, just the actual bendy arm and gator clip on the angle indicator tool. Not sure of its purpose.
Astonishing.
Hello what km was your N55 engine ? How you destroy it ? It was remap ? Oil change on every 30 k km ?
This video was a compilation of about 9 other videos he made, if you go back to his original videos, I believe he give more information.
Good video)
How is engine feeling for now? Still works well?)
Has about 5-6k miles on it now. Feels strong so far.
And, never use a power tool to wind down mains caps bolts! the same goes for cylinder head bolts, always do by hand, but check the bolt threads beforehand.
So much work.
Hi, do u have manual how to install everything in this engine?
Very nice job!! what is the green lines you put on the bearings for?? Thank in advance
That measures the tolerances to make sure they are in spec. If the ‘squished’ plastigage is too thick or thin I wouldn’t proceed with the install and have to get different bearing etc.
@@SimpleCarGuy Thank you very much! Cheers
Hey partner is it possibly to do the timing chain guide with the motor in.
Hi! Yes, it's possible. Depending on the model of the car, you may need to drop the subframe (it's like 8 bolts) if you want to do the timing chain at the same time and you'll have to remove the radiator fan and a few things on top of the engine to remove the valve cover. I go into a little bit of detail in the video on the timing chain: th-cam.com/video/-apNebfNCMA/w-d-xo.html
Thanks for watching.
You did injector the bed plate sealant wrong. Could possibly leak down the road.
How so? Can you please elaborate? Would love to add a note and learn for future.
Amazing video .
How much would it cost for an engine rebuild ?
Not sure, I just do this for fun, but the parts were about $3500 if I remember correctly
GOOD JOB 🙋
Great video if you can talk to us next time and not just to your self.
Start with " coming up". 🤣🍻👍
I have a 10 video series on each step of this rebuild with commentary. Check it out!
are you not supposed to plasti gauge the connecting rod bearings?
Ngl I wish I could do this myself, right now I got my 2010 535 seating in my garage with a bad engine. I prefer rebuilding it instead of buying a use sketchy engine online for $2,000… 🤦🏾 I’m having a hard time finding a shop that rebuild engines out here in the Lehigh valley Pa .
After how many kilometers need engine service (Crankshaft)
Ideally, never. It’s not normally a serviceable item. If your front or rear seals are leaking, that’s the time to replace them.
👍👍👏👏🙌🙌🙌💪💪.
Respect, so great job you have made.
How much would it be to rebuild a N20 engine on x3 28i twin turbo xdrive
good work!
Where you get the instructions from one the torque and bolt pattern
bro why couldn't you add the torch settings for every bolt!
But why not replace the rings too???
That was a goof on my part! Should have done it now that I think about it.
So I can rebuild a motor in 30 minutes?! I’m in the wrong profession 😩😂 jk great video!
Everything is easy on the internet!
Great video..but valve steam seal replacement was most important😢
I didn't think of that! Should have done those when the engine was out.
Hello, where did you find the tightening torques? Thanks a lot
I used newtis and BMW software at the time.
Did you forget to put the rear main seal?
Muy buen trabajo
Tengo el mismo n55
Me toca hacer la cadena
BAD ASS WORK THERE 🎉🎉🎉I'LL NEED YOUR INFO WE NEED TO CHAT
One of your pistons did not get a bearing... If am not wrong
Clips were slightly out of order. I, of course, installed the bearing just like the rest. Engine has been running for 2-ish years
clean
Просто лучший 🎉
hi where did you find the torque specs?
Iv found the conrod bolt specs (20Nm + 70deg + 70deg) but cannot find the specs for the main bearings.
thanks
Main bearings inner bolts 20Nm +70 ° outer bolts M8 - 8Nm + 90° outer bolts M10 - 15Nm + 90° all bolts new. Data from workshopdata
I used newtis.info and BMW's software that can be found on the internet.
Hello where did you find all torque specs?
I never hear good Things about the n55 are they really that bad?
They are not a bad engine, but people tune them and drive them hard. I have a video on all problems to expect on these engines.
How much would u charge for this job and how much was the engine
I don't do this as a job, I just did it to see if I can rebuild an engine. The second engine I bought was $300 as it had a spun bearing which required a full rebuild because the crankshaft was damaged. It's not really worth it to pay someone to rebuild it as it's cheaper to buy a used engine.
How much replacement engine n55 go for these days?
Probably around $4k, more with lower miles.