Turbocharged Ford 300 Inline Six Makes Over 500 HP on the Dyno - Engine Power S8, E14
ฝัง
- เผยแพร่เมื่อ 21 ก.ย. 2024
- Ford’s inline six industrial engine gets what you’ve been asking for...a turbo!
Check out the PowerNation store for shirts, hats, and more: bit.ly/39LkvsF...
Want to watch POWERNATION completely ad-free? Subscribe at the link below and receive the first month for just 99 cents: bit.ly/2DuRILC...
Follow POWERNATION Everywhere:
www.powernatio...
/ powernationtv
/ powernationtv
/ powernationtv
PARTS USED IN THIS EPISODE:
Summit Racing: Engine Brushes
More Info: pntv.us/pn_pt_1...
Summit Racing: Demon Carburetion Street Demon
More Info: pntv.us/pn_pt_1...
Summit Racing: Harland Sharp Roller Rockers
More Info: pntv.us/pn_pt_1...
Summit Racing: MSD Ignition Parts
More Info: pntv.us/pn_pt_1...
Summit Racing: Offenhauser C Series Intake Manifolds
More Info: pntv.us/pn_pt_1...
Summit Racing: Summit Racing HEI Distributor
More Info: pntv.us/pn_pt_1...
Summit Racing: Total Seal Piston Rings
More Info: pntv.us/pn_pt_1...
Summit Racing: Vibrant Performance Y-Pipe
More Info: pntv.us/pn_pt_1...
Summit Racing: VS Racing Wastegate
More Info: pntv.us/pn_pt_1...
Holley: Holley Sniper EFI X-Flow
Matco Tools: MATCO Tools are the Official Tool Supplier to Engine Power
The Industrial Depot: Tools, Hardware, Shop Supplies
Started at 88hp, finished at 522hp; has to be the biggest improvement from stock EVER !!
Seriously, what else gives you a nearly 300% increase in HP for essentially bolt ons, minor machine shop work, and DIY Garageability. Makes me wanna yank mine from my truck for a while.
@@kirbychristopher9741 its super easy my buddy makes 429 to the wheels with his 300
@@kirbychristopher9741 a Cummins you could get 300% increase with bolt ons
@@MrAppltec yes you are correct. However, Cummins bolt on's are twice the cost of what was done to this 300.
The thing would have put down more h.p. than 88 by simply giving it a basic tune up first.
Has to be the coolest engine power episode ever, thanks
Absolutely
Agreed
Yes
You ain't just whistling Dixie!
It’s a break from the V8s, a much needed one at least
This was a great episode, you built up an engine the average person can afford.
I think that would be the first build they did
What do you think this would cost from long block to 500hp,
@@jpotloverWhere I live you can find one running for about $200
One of the best motors Ford ever produced. They seemed to take abuse and still run forever!
I agree. Ford really hurt my feelings when they discontinued the 300. I drove an old 1970 F100 for 6 years and I was not easy on it. I broke just about everything on that old pickup EXCEPT the motor. And yes, it was the 300 inline six.
Definitely one of the best all straight 6 motors made great torque numbers!
Yeah as long as you didn't rev it to high and float the valves
@Adam Chapman nah the aussie barra is better. Dohc, not underpowered, and the factory block can handle 2000+hp.
And the 4.0 Jeep motor, both legendary
This was more satisfying and way more fun then almost everything else I've seen from this show. I really want to see them start making power on all sorts of different, underdog engines.
I had a smile on my face the entire episode.
There isn't a gearhead alive that grew up around 300s that didn't wonder why that bulletproof engine never got the love the 302 and 351s did.
I want to see more of this
@@francislutz8027 my first pickup was a slapped together jolopy of a ford f150 with a 300 and a granny 4, that motor drove me to the pits of hell and back, had a warped valve cover so i always carried a gasket and 5 quarts of oil for when it blew. dad still hauls wood with that ol rig, not fast, but he hauls it
To be honest thou the 300 isn’t A underdog from the factory it would out pull the 302 had a friend and his dad both bought brand new trucks only different was his dad sprung the extra money for the 302 but his son out pulled him every time they tested them out against each other and that’s a honest fact
*_THEY should do a ford, gm, and Chrysler inline six turbo build off.. As in same turbo and efi to see what made more hp then put them in cars to drag race them... Inline six muscle cars still way cheap under 20 grand mint condition.._*
@@francislutz8027 *_Like a multipoint efi custom build like Casey built back in the day but for inline six!!!_*
This is the best episode of Engine Power ever. PLEASE MORE 300 content. Push the boundaries of it!!! Sleeves and head, etc. More boost.
More boost, more fuel, more timing....I want to see a comma in those numbers
This things a 4wd tow pig and not too heavy either. Probably still gets 20 mpg
Aye! More boost AND more cowbell!
They should try the FORd Barra from Australia
Did you see the boosted 292 episode?
Being a huge I6 Ford fan, this episode gave me goosebumps. Outstanding job.
you like the barra?
Because it finally confirms a lot of our suspicions. You really can't go wrong with a big inline 6 and a big turbo
@@tturi2 I do it is a nice straight 6
me to.....big 300 ..6. Fan....had a
1993...f150. 4x4....300..6...motor
Snowplow on it.....got the job done with attitude. ...grrrrr.......
@@Hydrostream1972 If you still had that truck would you have the engine making 500 HP like the one in this video?
I've taken 2 of these apart about 4 times each now, and yes- These will run 70 mph on the highway with a half ton of sand in the bed, with 2 cracked pistons, all rings seized, and not 2 squirts of oil. Then I re-re-built it with 5 new pistons and all new rings, bearings, and a HO oil pump. Absolutely love turning the key on my '85 F-150. Runs smooth as a sewing machine, even the air conditioning holds a charge and works.
It may never go fast, but I can pull a stump at idle and 100% guaranteed to take me anywhere I need to be.
This.
Every gear-head friend I have has a similar story of an abused 300 that would break hearts, not parts. The old "they quit making them cause they can't profit from selling parts that don't break" story has stood the test of time pretty damn well
Its hard to kill an old Ford.
Had one of these in a 76 f350. Most of the truck rusted away, valves outta adjustment, and most service was "it's still running, drive it". Motor had an easy million miles on it. Still most reliable truck in the fleet.
Built Ford Tough! 👍 too bad everything that every company makes today is garbage.
I've owned two myself. Absolutely awesomely dependable engine the 300.
One of the greatest engines of all time. Awesome seeing it get some love.
My Dad was so sad in 96 when they made the new body style with the v6. He bought the last i6 they had because they were selling them side by side. The salesman asked which one he wanted,new body or current and there wasn't a bit of hesitation. On the way home he just kept shaking his head and saying he couldn't believe they were getting rid of one of the best engines of all time. He put well over 300k on that '96 f150 with the big six and all he ever did was scheduled maintenance and oil changes. Best truck ever and I wish every day that I had it right now.
And it's a shame all manufacturers stop making the inline 6 cylinders some of them bet ever made
I did a fresh rebuild on a 300 six, 268 grind comp cam, 240 heads, HEI distibutor, EFI split manifolds, and a Weber 38/38 on the stock intake, and my old gal cooks 🤙
I wouldn't even bother looking for one of these in a junkyard. Imagine finding someone's project car in a barn and going straight past it for the 🚜
It's a 300ci.
One of the absolute best engines ever.
Actually it's not. They've bored and custom built pistons.
@@bmstylee Okay... Is your point that its a 308 and not a 300?
@@bmstylee regardless its still best motor made.
@@fordnut4914 nice story. To bad it's not true. If it was so great as you imply why hasn't it been made in several decades? As Pat said it's a relic. It's completely irrelevant in a modern world. As much as i dislike the turbo 6 that Ford use now they can make the same power and torque at half the size.
@@bmstylee you must not know nothing about engines.
Yes most epic engine power episode ever that 300 is stout af.
G5
Six in a row will go !
But how much does it weight?
A barra is obviously better for power and sounds better.
@@tony_5156 Yeah but I dont wanna ship a whole block from Austrialia
@@tony_5156 And big block ford's are better for power and sound what's your point
I want this so bad. It’s the ultimate crawl around and tug truck motor. Even the NA motor is good with a manual and 4wd. It pulls way more than you would think quietly.
Those 300 motors were in so many 1/2, 3/4 and 1 ton even I bet some heavy hauling 2 ton or so cargo trucks and flat beds throughout tge late 80's to early 2000's, most underappreciated and overworked engine probably ever.
@@Roboticdoughbull3k im looking out the window at my 95 f150 5sp 2wd with this engine while watching this
It's easily attainable now. Summit racing sells the kit for a cunt hair under 3k!
Please don’t laugh.
I feel like I already know but, is this CA legal
Seeing that you started with 88HP, This engine is now putting out over 6 times that. Now we know why they last so long in stock form. I am putting one of these in my speedster build. I am starting out stock and then after it is on the road, I am building a monster 300 for it. It is called Project Boat Tail. Thank you for doing the R&D for me guys.
Get an 93-95 one there EFI and make 150hp stock I have one
@@jamesworkman686 efi will require engine management taht os much more expensive. Carb is the way to go
@@jamesworkman686 That is the plan
To be fair, when it made 88HP the governor for the industrial application was still in place(you can see it above the alternator in the first dyno run). Just removing the governor and properly tuning the stock carb should have easily gotten it close to the automotive engines 170 gross HP rating.
@@STAY-GOLD-VINYL The efi ones had the good exhaust manifolds and the higher compression head (though i think the carb head can be made to flow better). I think starting off you'd be better off to carb swap an efi motor than to start with the carb one. Youre swapping intakes to lose the YFB anyway
I'd actually like to see this shoved into some old sleeper grandma Ford. Maybe an old 1979 Fairmont.
The station wagon variant
@@shadowstallion71 will not fit, block is too long. unless you can find a 1 inch thick rad that can handle that power or modify the firewall and move it back about a 1 foot. How do I know? My dad tried to put a 300 Straight 6 EFi in a 91 foxbody mustang...just because he was bored one time. However, it will fit into a AMC gremlin through >:)
An old stock appearing f100 would be badass too
64 Falcon 2 door
Thanks for the chuckle.
One of the greatest engines ever.. truly stands the test of time.. seeing it respond so well to forced induction makes me giggle like a fricken maniac!
I've got to thank PowerNation for listening to their viewers and making this episode possible! 👍
Ford 300 is one of the best engines ever made. I drove one for two years, doing flooring work, overloaded as hell, and had 488k miles on the odometer. Had close to 550k, when trans literally fell out, van had some serious cancer. What hurts the 300 so much is that 60's cylinder head. I'd love to see a modern free valve head made for the 300, and see how much it wakes up.
Have you seen the Australian barra motor?
Literally those inline 6 engines (the AMC, slant 6, and even the chevy 250/292) were just undestructible, wonder if someone got one to a million miles...
@@Ausblack yes McM, uses them from time to time, and skid factory. :)
@@Thraser999 atomic performance or nizpro is worth a look
Dragboss garage was just talking about a Cleveland headed 300 built by Bruce Sizemore that made 500hp back in the 70s.
I wish Ford would make this engine in this configuration. Ive got a 3.5 ecoboost and i love it. I can’t imagine this thing under my hood! Love the inline engines. Naturally balanced.
Buy a Barra from us here in Australia 👌
Now this is cool. The 300 is entirely overlooked. It would be nice to see more projects with it.
You must not know anything about cars 🤦 . Heavy motor needs to be in a heavy frame . It's bulky and expensive 🤡
@@JL-hw5rtclown
@@JL-hw5rtok who cares this is still really cool they made 500 hp with a engine that only made 88
@@JL-hw5rtpeople have been running these in dirt track racers and drag cars for decades 🤡.
A build list for the final NA with 287ish horsepower would be pretty sweet. Sounds like a fantastic daily driver F150 engine.
it was listed on another episode. though the roller lifters only added couple hp so barely worth adding them.
@@SgtJoeSmith that’s for longevity not power
That's what I was thinking
@@Agilepickleunite
Not trying to be a troll, but I have 500k on stamped rockers that'll beg to differ.
The rollers are for alleviating a slight bit of friction in the upper end of the engine, but won't do much for longevity.
Gee thanks guys. My 87 f150 300 4x4 B.W. 4sp stick short bed I've had for 20 years honked twice while watching this video. My other is a 93 f350 7.3 4dr 4x4 auto and it deserves a turbo first. Both best motors ford ever put in a truck. My grandkids will drive these trucks. Both have pulled unbelievable loads. Neither are fast but are unstoppable.
My friend had one in a delivery van and ran it for months with 5-10 lbs oil pressure.
Guys, this is probably one of my favorite episodes, and I am not even a Ford guy! Awesome! I think our old wrecked 78 F250 with the 300 6 just stirred from the grave down on the farm!
You can be a fordguy now, nobody will hate you.😆
I hope you actually do, its a piece of American history.
Imma mopar guy witha '77f150np435np205 300! had a '74 w100 and Father's company had a '75 econoline with a 300 and while the 318 is awesome that 300 is too! now to find a dodge to stuff all this ferd into and hide it away! heh,
@@zarkeh3013 - You can just tell the assholes its a slant 6 and leave them guessing. From the exhaust they really can't tell because the IL6 engines are quiet. Chrysler has one which is just a miniature version in the Jeeps. The 4 liter. They bulit it up to around 200 stock horsepower and put it in everything.
Put in this ford and close the hood with a 5 or 6 speed. They won't know WTF kicked their butt and you are under no obligation to show them LOL
If the cab is any good, let me know...my F250 has some bad rot! :D
Sure brings back memories. Built one 20 years ago with the same intake/header combo, Holley 390 4bbl, Comp 260H cam, mild porting on the stock head, and a .030 9:1 rebuild. 242Hp and 323Tq
Do you know how much horsepower and torque yours made?
@@cesarprieto8279 242Hp and 323Tq
Did the same in highschool in a shortbed ford
@@cheeseandpickles98 I just acquired one yesterday 84 300 Inline 6 granny 4 speed 4wd flatbed with 33s 70,000 original miles
Mine is a 96 F150 4.9 EFI 5 speed. At 70 mph it turns 2250 rpm. At 3000rpm she’s doing 93 mph. I usually don’t break 2000rpm. Purrs like a kitten 70 series Flowmaster 3” stainless from Y-Pipes. No cat no egr or pump. I get 18-23 mpg! Towing my 5000 lb camper 11-14 mpg. 290,000 miles. I see no reason to mod it ! It’s just to much fun as is.
The 300 is just one of those engines that everyone loves and has a respect for. Never met any gearhead who didn't like the 300. I grew up with several full size Broncos in the family, what I wouldn't give for a decent example with a 300 and manual everything behind it.
That's an absolute fantastic motor . I seen one of those motors go 36000 miles without an oil change. And when Ford put fuel injection on it that really woke it up.
Unfortunately that doesn't say too much lol, when I was a lube tech I changed a Kia souls oil for the first time in its life at 72,000 miles. The owner had bought it new and never once had the oil changed. Only got about 2qts of sludge out but it got new oil and was good to go
@@MFU.team.4367 bullshit... There's no motor in the world that will last 72000 miles without an oil change. I've worked at KIA store those motors are terrible.
@@bige9830 I've seen a few Honda engines go over 40k without an oil change.
@@bige9830 we service our paccar mx engines on 75000, with idle time less than 10 percent, 60000 miles if over 10 percent,
@@youtubeisawesome2487 Those are diesel engines. It's a completely different animal then a gaser . Low Reving . The oil has a ton detergents in it . How many gallons of oil does that take? And I'll bet your dollars the donuts has got a low micron oil filter on it too.
This has been more interesting to me than most of the V8 builds! I thoroughly enjoyed watching Pat's expressions at the dyno!
Great job guys! Thank you!!!
It's fun, seeing someone finally giving the "Big Six" the recognition it deserves! Good job, guys! I had a 1982 Ford Econoline van, with this engine in it, and I agree: This is the best inline six cylinder engine on the planet. I gained a lot of top end torque, by merely installing a bigger exhaust and down-pipe on the stock exhaust manifold, paired with the factory intake and mono-jet carburetor.(Identical to what was on your engine when you got it) I had the 4-speed overdrive transmission, which was created by changing the 3rd gear ratio to create the overdrive. That meant, the transmission acted like it was a 5-speed transmission, missing 3rd. With the huge RPM gap between 2nd and 3rd, it would "run out of breath" in second, before I could get the RPM high enough, to be in its torque curve in 3rd. The big exhaust solved that, by giving it enough torque band, to cover that spread. I was able to use it to pull a travel trailer.
This has to be the most interesting engine build series on all of youtube. Well done!
W0
P
O
This would be such a mean setup in a classic bullnose build! I’d love to see it in a lowered 2wd street truck or a 4wd mudder, that would be so cool! This has definitely opened my eyes to the potential of the Ford 300
Throw it in a single cab Ranger short bed and let it take folks to gapplebees
@@Truckerdaddy are we thinking ranger the trim package or ranger the truck? I’ve got a 1991 ranger that would love the extra power. Either way it’d be a heck of a vehicle
@@cheynsanders5506 the mini truck. Not the full size ranger from the 70s.
@@cheynsanders5506 one issue you would have is space, to make it work you would likely need to trim the firewall for the bell housing to fit. You also would need to run electric fans because a mechanical fan would most likely hit the radiator.
It certainly would not be an easy project but would certainly be unique.
@@cheynsanders5506 another vehicle option would be a Foxbody mustang or any mustang for that matter. I mean if Westin Champlin can shove a 12 valve Cummins in a 2015 ecoboost mustang then a 300inline shouldn't be too bad.
My concern is always longevity. I’d be interested in NA upgrades at the 250-300hp level that still preserved the reliability the 300 is known for.
With the turbo: o-ring the head, steel head gasket (may already have one), water injection, inconel valves, electric water pump drive. Their intercooler helps keep temperatures down. The piston rings become the limiting factor, but they might last 100k even with hard running.
It will last as long as the Toyota turbo i6s. Strong ass engine. It can handle the turbo.
My bigger concern is torque, for a pickup build
Of course, keeping longevity
@@rylan642The nice thing is this is an industrial motor built like a brick shithouse with very strong components and internals that have great reputation. They did not need alot of boost to make over 400 hp and plenty of torque to back it, which would be more than plenty, unlike the new ram hurricane which is a 3.0 gasser non industrial motor pushing 27 lbs of boost to be in the 500s club and 22 lbs of boost to make 420hp big difference those motors are not going to last in my opinion even for an I6 I think they're too damn hopped up and not built strong enough because it's for mass production and its stellantis lol.
@@jamesj5130 I meant for my case only doing 5 or 6 psi
Pat:
Frankie:
There’s only one word: WOW!!!! Unbelievable that that little engine makes 522 hp and almost 600 pound feet of torgue!!!! WOW!!!! Greetz from the Netherlands , ramon
Meh. The 2JZ is much more impressive engine.
@@basshead. 2jz wasn't build for industrial work. The 300 is way more impressive since it was only meant to be a work horse engine and not a performance engine
@@carsonmeyer2808 The 2JZ is much smaller engine than the 300 and it can make over 1500hp.
@@basshead. I just don't Find it as impressive. A stock 2jz can hold 800. This build for the 300 wasn't stock but again. It's technology from the 1960s/an Industrial engine made to run long hours and low power. Far more impressive in my eyes
@@carsonmeyer2808 You are impressed that it held up 4-5 short dyno runs? You can slap a turbo on anything and make power.
I have watched this series three times now since it first came out. I have honestly been bored with the same old builds for a long time now, but this is a reason to dream, plan, save and scheme. Even if you nock 150 horses off you still have reliable fun that ain’t the same as what everyone else runs. Love It!
*We've been awaiting.This is more fun that the 'Coyote' build. WTG Fellas.*
Ohc builds are boring
@@shadowopsairman1583 nah
Haha it's only 2 cubes smaller then a 5.0,so it should run
(Or not, we know the heads flow for shit but for what it is it does damn good)
Smooth as a sewing machine too.
More.of.this.
This has that "buddies hanging out at the garage" feel to it.
Every single racer that has grown up around the "300 that doesn't break" wondered what it would take to break one.
Apparently, if you keep it stoich and don't exceed 1 bar she's a screamer!!
Barra what?
522hp on only 13.2lb of boost is insane.
And that's turbo. NA has waay more reaction. The 470HP 221ci carbed NA variant of this engine revs up to 9500 RPM on argentine Turismo Carretera series. th-cam.com/video/AlF5laVMdrI/w-d-xo.html
I want to see it do 3 and half bar and hold it.
@@Toxic2T the '221' made in Argentina was based on a 'Falcon Six' that was '170' in the beginning, them pumped up to '187' and finally the '221' there. Completely different engines than the '300 Six'...
@@stephenkeebler732 Yes they came here are 177, 188 then developed to 221. the 177 came in the early 60s american Falcon
WOW!! Those are some pretty kick-ass numbers for a straight 6. Hope it inspires some folks to think about these awesome engines for their project.
I got 2 300 6 one in a 150 1996 other in a 78 f150
This is what I’ve been waiting for.
I was expecting to see Richard Holdener hiding behind a tool cart giggling to himself.
Just see his bald head poking around the cart just as it starts making boost.
Whisperings of ring gap and a little more boost… lol
Lol, you know Richard felt a disturbance in this force as this boosted girl went through her paces.
So, cool to see!! I own a 76" F-100. With the 300- 6 , 3 on the tree. Been the most dependable vehicle I have ever owned. Thanks for the video!
Great job Pat and Frankie, my favorite Engine Power build to date! Everyone loves and has a good story about a 300-6 they had.
Exactly, such an iconic and prolific engine. I would love to see more series with the criteria of iconic, in tons of stuff, not really sought after but simultaneously loved by most who have owned and worked on them.
That's weird but true. I never thought about that. I have a million stories.
Just like Pat says, gotta love those old 300 sixes. I fondly remember my 84 ford. Almost 300K miles and never cracked open the engine. Never added a single drop of oil between changes.
One of the best engines ever produced mine has 210,000 miles never uses a drop of oil between changes using Shell Rotella T4 10w 30 diesel conventional
I'm not buying it. 300 000 miles and never been serviced? Come on.
@@captainchaos3053 thats not what he was saying though
@@gerrit2107 that's because he has an American education. they dont teach reading comprehension they just teach them to repeat the words not understand the words
@@dertasdert2419 ah yes, that makes more sense :)
Those old Ford engineers knew how to build! This was a truck motor. What a pleasure it would be to have one of these!
Pat's look of trepidation made me watch the last pull thru slits in my fingers but, I'm overwhelmed at the results. What a great engine!
Hands down best episode yet.
I, and every friend I have, have always had a love for the old 300 motors. With the Barra being not offered stateside, we all wondered what an old 300 would do.
I hope to see many many others follow your footsteps and see a slowstang powered by one on the various street/strip racing social media accounts soon.
I had a grin on my face as soon as you showed that rusty hunk of iron.
I am in AUS, it would be great to see the guys do a Barra and be blown away literally.
@@Blackbirdrod81 a Barra engine its same thing on 300 .just the head its crossflow air and the its the plus cause I have more room to grainger some aluminum of and. Make bigger exhaust and intake, cause they Barra its aluminum head then add goods to make power 800hoses
Barra the world 💯
Really cool seeing this. Gives me some motivation on my Dads old 96’. Spent a bunch of time/money putting in a reman long block only to have head gasket/coolant loss issues. Thanks for the motivation fellas!
Amazing engine and a lot of people do cool stuff. I've read on the forums of heavy haulers that people put on a cummins turbo then take the cam and advance it one or two teeth to move the power band lower in the rpm range and make mountains of torque. I rebuilt a 300 that the cylinders were so worn in the center that the glaze breaker stone wasn't touching and the bearings were only showing the copper. New bearings and rings and she still ran amazing.
Been waiting patiently for Richard to do one of these. He's mentioned it a time or two. Y'all beat him to it and knocked it out of the park! Those numbers were Amazing and not even at a full atmosphere!
I've always wondered what this engine could do if pushed to its limit. You guys made my day.
In the early 1990's, we used to sell this motor in F-150's as the million mile motor because they never broke down nor wore out in a stock configuration.
@@bigboreracing356 , maybe the durability and reliability performance had something to do with it being in production since 1965? Nah, it was just a low rpm powerplant. You're right!!! SMH
@@bigboreracing356, my sarcasm wasn't due to being offended. It had to do with the lack of competence about the topic. The emissions may have had an impact on the discontinuation of production of this powerplant. The 302 in the F-150 only had minimum performance gains and less reliability. 60 mph you say, where do you live; don't answer that! Lol The 60's were the muscle cars original era. I would rather have a 1996 F-150 with a 4.9l I-6 than that year with a 5.0l V-8 or a 1997 F-150 with a 3.7l V-6 or a 4.6l V-8. Thanks for your comment, good talk; really!
@@bigboreracing356 Big lazy motors are reliable, the fuel efficiency wasn't so great but it sure was an admired workhorse
@@bigboreracing356 , no truck salesperson would sell an F-150 with an I-6 if they were planning to pull a maximum load ever. If they needed more towing capacity we would sell them an F-250 with a 5.8l V-8. Let me explain the reason for an F-150 reg cab truck. It's and entry level truck for the person or company that only needs basic performance and capability with marginal towing capacity. Have a nice life.
@@bigboreracing356 , you love to see your works of splendor typed out for all to see. Have a nice life.
I have been waiting for this episode for months, I'm so glad it's finally here!
ONE OF THE BEST MOTORS FORD EVER MADE! EMISSIONS KILLED IT!
Glad to see Pat stepping out of his NA comfort zone!
I've always been a 302 guy.. but damn this engine build has me rethinking my whole truck/car life
There's a reason these are legendary, if you overbuild everything and ask it to make 100HP all day long it will arguably last virtually forever with decent maintenance. If I wanted to run something like this in a daily driver, I'd go for the 250 HP + 330 FT/LB NA config, it'd still last almost forever and be a damn good motor for a truck application. It was a blast to watch you guys push this to over 500 HP, but I don't think I'd want to run it like that for very long. :) Great series guys, it was really cool to see the 300 inline 6 get some love!
Been waiting for this all summer!! Finally comes out on my last day of summer, sweet!!
I LOVE this! 300’s are awesome and always wondered what one would do turbo’d. Thanks guys!
Wow!
Its not just the engine you start with. Its not just the power you end with. Its the workmanship, craftsmanship, superb equipment, superb materials, superb facilities. Its all of it.
What a great window into your business.
Honestly this is the best episode ever!! Imagine this in my old bronco.. I'd rock it for sure!
Wicked to see. I take care of around 40 of these that run oilfield pump jacks. Would be wicked to see this turning a jack 😂
It'd run that one pump jack so hard, you could shut the other 39 down, and still make production
Kinda pointless dont those jacks only turn like 1800rpm
@@rustedratchetgarage6788 yea was just joking.
@@rustedratchetgarage6788 Kinda pointless? Kinda joking.
The 300 is my favorite engine, but I never considered it for a serious power plant. I might have to re-think that. Another thing: I didn't know about the split manifolds. That would allow for a true dual exhaust. I like it!
also would allow a twin-turbo setup
@@YourScaryMother twin turbos would also allow for dual quads😁
Me neither but we're going to now
@@YourScaryMother Or even better, proper twin-scroll big turbo 👀
@@Noman1000 We're talking about a split manifold here, where plumbing it for a single turbo is going to be more problematic. Also, the bigger the turbo you have, the more exhaust pressure you need to get it to work optimally, so going big is not always better, and generally, two smaller turbos will be able to produce more boost than one bigger one (and usually at a more efficient part of the RPM curve). Though, of course, it will depend on if you are doing a street/strip or a pure race car where you would have a line-lock and two-step, etc.
That was incredible! This is one of my favorite engines, and I have really enjoyed watching you guys make it even better. I would have been happy with 300HP!
The kid has my respect. He knows his stuff!
Mine too,,Yo👍💯
That's sweet. I had one with a 4 speed for my first truck. Took a 12 inch thick maple tree clean off and almost bent truck in half. Fired right up without anything turning. I'm a Chevy guy but that old 300 holds dear to my heart.
Pat wanted more boost like he wanted more pens in his pocket. Great episode! 💙
Hahahahaha
😂🤣😅😆😄
@@nonsequitur807 Brought back memories of my dad coming home from work and all his writing utensil-filled pocket protectors. This was the 60's.
@@darylsmioth1904 He must have been an engineer. Same era
Love the underdog engine stuff. Keep that stuff up! Throw in more engines that don't get enough love!
Drove a 79 F100 with 300 for 350,000 miles and really enjoyed this build. Wish i had it back to 'Build It'. Maybe a future build somewhere in my life. Great Job Guys! Great Job!
Awesome results!! Would love to see a centrifugal supercharger on it next and compare the Dyno curves between the turbo and the supercharger!
My jam dropped when you revealed the stats on the last run! You guys have the best job in the world. Playing in the world of big boy toys.
There are reason(s) those 300 6's lasted forever, and you guys just nailed what they were.
My two favourite underrated engines are the Chevrolet 4.3 V6 & this glorious Ford 300. You fella's did them both super justice. I've owned both, and loved both for different reasons.
Thanks a bunch.
By far my favorite series so far, I’d love to see this in something soon
by far the best episode in my book. the excitement yall keep getting was classic. Im not just saying that cuz im a inline 6 guy.
I had a 300 6 in a Bronco. It wasn’t fast but it was unstoppable. It’s one flaw was a sticking float valve. I still kidded about fixing it with a hammer.
You guys have the most fun job ever, great video.
Ford has made some great engines over the years and this is one of them!
Wish they would bring back a good straight 6
И не только Ford) Ваши автомобили лучшие! 👍👍👍👍🤝
Thank you for finally giving the love this motor deserves. Best engine by far.
Gentlemen, that's what I'm talking about !!! I had a 4.9L I-6 in a 1990 F150. It was such a dream to work on, with so much room under the hood. Seeing this video make me wish I still had it.
This episode was so much fun to watch, I didn’t even know I needed to see this.
Thank you to the builders producers and crew for making this happen 🙏
I built a 300 with a 2-barrel intake, 302 carb, headers, and a torque cam. It twisted the 1/2 ton drive line out of my truck a piece at a time in 6 months. I had to replace Everything with 3/4 ton Dana Posi, 1-ton granny trans, 11-inch dump truck clutch and a custom driveshaft. Two years later I had to weld, box and fish plate my frame back together to live behind that engine. I NEVER had any use for a V-8 after that.
Always wanted to build one of these, not sure how common it is but these guys proved it was a worthy engine build 👍
Have to say I love these type of builds. So cool to make big power with other engines than a LS.
Those 300 inline motors are torque monsters.
That looked fun as hell. From the building to the testing. Great job guys!
Thanks for the video. I'm building a Chevy inline 6 292 with 6-71 and 2 650 DP. Billet crank, cam and rods. Ryan Falconer V-12 head (crossflow 340I 220 E). 5 stage dry sump. Electromotive coil over direct fire ignition. Looking at 1000 HP. It's going in my 53 Chevy 1/2 ton pickup.
Damn son 🤑🤑🤑🤑🤑🤑🤑
awesome setup. I highly recommend running the wastegate hose after the intercooler due to the pressure drop. when I did that change on my car boost pressure was steady all the way to redline.
Wow. That block will take anything you throw at it. Old School FORD Tough! Excellent video.
Had I known you were going to turbocharge the build:
Borrowing from Pittsburgh Power-I would have stuck with lower compression ratio pistons. This is the Pittsburgh Power method of reducing the peak pressures but still building a lot of horsepower big semi truck diesel engines.
I would love to see you at 20 lb of boost would be on 8 1/2 to 1 compression ratio pistons. I had a 1992 Ford Probe with eight and a half to 1 compression pistons and it was a slug. I was one of the 90%. The lucky 10% had a turbocharged version of this car with the same engine and it rocked! Especially by 1992 standards.
Next Ford 300 l6 build see if you can build it to be turbocharged from the get-go. Attempt to get a more sturdy head gasket.
It's so incredible that you're almost getting two to one horsepower to cubic inches!
Learned so much about the anatomy of a turbo system from this - on top of the epic result from the I-6!
That's a pretty smooth power delivery. Almost linear. Damn what a nice build!!
I grew up watching every sunday morning the CMT channel, I'd watch shade tree mechanic, bill dance fishing, etc etc I love shows like this. I'm 43 now and still doing the same thing lol
Definitely the best episode yet. Way more interesting, working with something oddball. Keep it up!
2:16 built like that is something a normal person can do in there garage its reasonable and 270 hp and 338 pound feet of torque would run pretty good in an old 4x4 F-150 i think the aluminum head and cam did most of that! pretty cool
All I can say is!!! WOW! Thank is impressive. I’m a Chevy guy and this impressed me. Great job guys.
I've never been so stoked watching one of these videos.
I LOVE when you start with nothing really....and get SOOOO EXCITED building HP like this and you guys expressions made this worth it!! Love you guys..do more like this take Small Disp engines and make MONSTERS!!!!!!!! Good Job Way to Go!! and love this!!
A bought a 1995 f150 with a 300 4.9 out in Denver Colorado, I did oil change thermostat belt got on the truck and drove it all the way to Californian and roll this day I’ve been using the truck as my daily driver. I’ve had the truck for near one year now and I can say I love it it’s a five speed sheet bed 4x4 .. dude if you guys would raffle that engine or you ever want to sell it I hope you pic me to win it lol.. I never want to sell this truck I want it to stay in the family for ever my dad had one when I was younger and he passed it down to my older brother I always wanted one because my older brother taught me how to drive stick shift on it so every time we work with our pop’s I would go get lunch for all of us on that beautiful blues truck 🛻. Now I want to pass my truck to my son or daughter .. I love 95 and down Ford trucks and it better be a straight six.. if you’d like to give that beautiful engine a home I promise it’ll always stay in the family.. good bless us all and America... man you guys are awesome thanks next you should build a dodge slanted six....
I loved the tension in the air as they slowly cranked up the boost.
This was great! I’d love to see a build up of a less popular engines like the 400 Ford. I liked seeing the 300 make more power than most v8 engines tho
I love the straight 6's, currently in love with the 98' Volvo s90 but also had an older late 80's Mercedes Benz 3.2 that just rocked but the 300 started it all in a 70's ford 4x4 tow truck... glad to see it
love it guys! This is such a badass engine
Walk softly and create your own atmosphere... :)
I think a follow-up is in order. Head studs, good gasket and more spring!
Honestly though with 6-8psi that thing would be an absolute ripper in an 80's F truck. Find an 80-86 Bullnose short bed F-150, add a late 70's D44 solid axle to the front with some 6" lift springs, a 9" in the rear with add a leaves and maybe blocks for about a 4" overall lift, some 35's and that engine with 6-8 psi making around 450hp and 500+tq. You could run a C6 with 3.50 gears with little problem. Honestly it would be a relatively cheap build overall...