Didn’t hear it mention but before you go through all this with the deck, be sure all the tires are inflated to the right pressure. Nothing worse than doing all this measuring just to realize you had a low tire and have to fix it all again
The knob on my ZT2 says it should be 4.5inches in the top setting, so i just cut 2 pieces of 2x4 exactly the same then adjusted the deck till the blades just touch the top of the 2x4's. Then I turn the blades and make the front to back setting so it's just over the 2x4.. that way my height setting is actually correct because i mow at different heights depending on the amout of rain we are getting and how late in the season it is.. just my 2 cents..
My deck was horribly out of whack either from the factory or final assembly by the dealer I don't know. Thanks to this video I was able to adjust it and now have a cut I can live with. It was so bad though. Thanks again!
I just bought a zl1. The deck is all jacked up on it. Front of it is way high. Like a kinder Gardener assembled it! To set my cut height do I measure the outside side of the Deck to obtain 2 inches when my dial says two? Or do I use the cutting edge of the blade⁉️
Whoever assembled and welded my deck didn't finish weld on of the adjusters and it was just hanging loose when I removed the deck to clean it and swap to mulching blades. I wish I had noticed that while it was under warranty.
I want to know if it will goto 4.5 inches? That's what u set the dial at 4.5 for the blade height...but it measures 4 inches...mine is set for 4.5 but measures only 4 inch. Thanks!!!
I have a question. Since the deck height was set at 4.5 inches before you started, wouldn’t you try to get the blade height to equal 4 1/2 inches or close to it? It’s an honest question as I am trying to Level my mower right now and want to make sure it’s right. Thanks again.
My son hit the fence and the deck is leaning down. I followed what you did and is still looks the same. I went over everything and nothing looks broken. Any suggestions?
Mr jim i need your help. I cant find a good video how to install drive belt or how to anchor that spring from the drive belt. I need your expertise Thank you
I just found your videos and I really like the content! I think you should look into a GoPro with chest mount. It can add a new angle to your videos and make it easier to explain what your doing in a smaller space.
I know this is about leveling the deck, BUT how about coming up with something that can be attached to deck pedal, so I can use my hands? Can you come up with a mod? Why? Because I’m disabled and cannot use my feet to push the pedal, but can still drive a ZT1 54. Plus, think about older folks out there mowing…not everyone can push pedals. Had a RTZ 50 with deck adjustment under the seat, that was easy…what was Cub Cadet thinking? Never mind, lowest common denominator to sell them I suppose. Anyway, you’re a very helpful guy, so maybe you could invent something? If you do, pen me in for buying one…. 😎
(click read more) Thank you very much for watching and God bless. ✅Deck leveling gauge amzn.to/3gNj0TC ✅ My T-shirts. Thank you for supporting my channel✅ diy-jim.creator-spring.com 5% off shirts use DIYJim2021 when checking out ✅Send me a thank you✅ DIY Jim PO Box #105 Hughesville Pa, 17737 ✝Bible ESV easy to read amzn.to/3qshNQP ✝Bible NKJV amzn.to/30ns322 ✅Titan Solar Generator (large generator) poweredportablesolar.com/ref/48/ ✅Sony ZV-1 (camera I use) amzn.to/3MxVeG2 ✅sony wireless UWP-D (mic I use). amzn.to/3LEPV6m ✅Go Pro that I use amzn.to/2WC6WXH ✅Wireless mic used: Rode Wireless Go amzn.to/2WxQt7c *Full transparency. I am a participant in the Amazon Services LLC Associates program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites. *Disclaimer - Thank you for visiting my TH-cam channel. Please understand that the content on the DIY jim TH-cam channel is intended for informational purposes only. I make no warranties about the completeness, reliability and accuracy of this information. Any action you take upon the information posted on my TH-cam channel is strictly at your own risk, and I will not be liable for any losses and damages in connection with the use of my TH-cam channel. #cubcadetZT2 #howtolevelyourcubcadetultima #howtolevelacubcadetzeroturn
Why not use a 1x2 or other small short stick and hold it against the blade. Then use a pencil to mark where the blade hits the stick. Measure that and you got your height. HA! I commented before I saw your homemade measuring device.
Didn’t hear it mention but before you go through all this with the deck, be sure all the tires are inflated to the right pressure. Nothing worse than doing all this measuring just to realize you had a low tire and have to fix it all again
I think you are right I did not realize I forgot to mention that. I’m going to put that in my first comment. Thanks
The knob on my ZT2 says it should be 4.5inches in the top setting, so i just cut 2 pieces of 2x4 exactly the same then adjusted the deck till the blades just touch the top of the 2x4's. Then I turn the blades and make the front to back setting so it's just over the 2x4.. that way my height setting is actually correct because i mow at different heights depending on the amout of rain we are getting and how late in the season it is.. just my 2 cents..
Thanks for watching, happy cutting.
My deck was horribly out of whack either from the factory or final assembly by the dealer I don't know. Thanks to this video I was able to adjust it and now have a cut I can live with. It was so bad though. Thanks again!
Glad I could help, thanks for watching
Just what I was looking for. My front of the deck is way off so thank you for this video
welcome thanks for watching
Nice work, very important adjustments, thank you for sharing this video.
Welcome thanks for watching
I just bought a zl1. The deck is all jacked up on it. Front of it is way high. Like a kinder Gardener assembled it! To set my cut height do I measure the outside side of the Deck to obtain 2 inches when my dial says two? Or do I use the cutting edge of the blade⁉️
The cutting edge
Good video by a good mechanic. Thanks!
Thanks for watching!
Awesome Video, Brother. I plan to purchase a similar Lawnmower this year and your video looks really helpful for my maintenance of it
Thanks for watching
You might check your tire pressure in both tires to make sure their the same before adjusting for 1/8"
I think I did did I forget to show that in the video? Thanks for letting me know
Awesome Video. Thank you So Very Much Jim!
Welcome John thanks for watching
What is the reason when you`re one end of the blade is higher than the other end
Because the front of the deck should be lower than the rear.
Whoever assembled and welded my deck didn't finish weld on of the adjusters and it was just hanging loose when I removed the deck to clean it and swap to mulching blades.
I wish I had noticed that while it was under warranty.
Holy smokes I would be mad. Thanks for watching
I want to know if it will goto 4.5 inches? That's what u set the dial at 4.5 for the blade height...but it measures 4 inches...mine is set for 4.5 but measures only 4 inch. Thanks!!!
I have a question. Since the deck height was set at 4.5 inches before you started, wouldn’t you try to get the blade height to equal 4 1/2 inches or close to it? It’s an honest question as I am trying to Level my mower right now and want to make sure it’s right. Thanks again.
I guess you could level it than check to see if the heights match the dial. Thanks for watching
My son hit the fence and the deck is leaning down. I followed what you did and is still looks the same. I went over everything and nothing looks broken. Any suggestions?
Sounds like something might be bent.
Thank you for the advice.
Glad it was helpful!
How do l determine whether to raise one side or lower the other side to level the deck?
Really does not matter just make it level. Thanks for watching
Mr jim i need your help. I cant find a good video how to install drive belt or how to anchor that spring from the drive belt. I need your expertise Thank you
Sorry I don’t have a video on that. Sorry I can’t help.
Can i Take the batery off
Good stuff, thanks 👍🏿
Thanks for watching!
When i cut low i can’t back up without my blades hurt ground . Why??
Not sure, sorry this was my neighbors mower.
I just found your videos and I really like the content! I think you should look into a GoPro with chest mount. It can add a new angle to your videos and make it easier to explain what your doing in a smaller space.
there is also a head strap that could go hand in hand with the chest mount
Thanks for the tip! And thanks for watching
Is 1/8th of an inch off really that bad? l think it'll be ok and would not make any adjustment. That's close enough.
thanks for watching
Thank you
Welcome!
I know this is about leveling the deck, BUT how about coming up with something that can be attached to deck pedal, so I can use my hands? Can you come up with a mod?
Why? Because I’m disabled and cannot use my feet to push the pedal, but can still drive a ZT1 54. Plus, think about older folks out there mowing…not everyone can push pedals.
Had a RTZ 50 with deck adjustment under the seat, that was easy…what was Cub Cadet thinking?
Never mind, lowest common denominator to sell them I suppose.
Anyway, you’re a very helpful guy, so maybe you could invent something? If you do, pen me in for buying one…. 😎
That pedal is hard to push not sure if I can come up with that. Sorry
You forgot to check the air pressure in the tires.
Your right never realize that. Thanks for letting me know
(click read more)
Thank you very much for watching and God bless.
✅Deck leveling gauge amzn.to/3gNj0TC
✅ My T-shirts. Thank you for supporting my channel✅
diy-jim.creator-spring.com
5% off shirts use DIYJim2021 when checking out
✅Send me a thank you✅
DIY Jim
PO Box #105
Hughesville Pa, 17737
✝Bible ESV easy to read amzn.to/3qshNQP
✝Bible NKJV amzn.to/30ns322
✅Titan Solar Generator (large generator) poweredportablesolar.com/ref/48/
✅Sony ZV-1 (camera I use) amzn.to/3MxVeG2
✅sony wireless UWP-D (mic I use). amzn.to/3LEPV6m
✅Go Pro that I use amzn.to/2WC6WXH
✅Wireless mic used: Rode Wireless Go amzn.to/2WxQt7c
*Full transparency. I am a participant in the Amazon Services LLC Associates program, an affiliate advertising program designed to provide a means for me to earn fees by linking to Amazon.com and affiliated sites.
*Disclaimer - Thank you for visiting my TH-cam channel. Please understand that the content on the DIY jim TH-cam channel is intended for informational purposes only. I make no warranties about the completeness, reliability and accuracy of this information. Any action you take upon the information posted on my TH-cam channel is strictly at your own risk, and I will not be liable for any losses and damages in connection with the use of my TH-cam channel.
#cubcadetZT2 #howtolevelyourcubcadetultima #howtolevelacubcadetzeroturn
Why not use a 1x2 or other small short stick and hold it against the blade. Then use a pencil to mark where the blade hits the stick. Measure that and you got your height. HA! I commented before I saw your homemade measuring device.
Guess we think a little alike, thanks for watching Daniel
A paint stir stick from the hardware store if you don't have a 1x2 piece of wood. Cheaper than buying a 1×2 and easier to mark on.
Bubble level.
No need to do the rest again.
Thanks for watching
That's right use the B. Level and save time!!!
Proper tire inflation and bubble level. I agree.
Jeez. Just by the tool before you make another video.
Thanks for watching
Thank you
You're welcome