Replace Transmission Gasket, Pan, Filter - TH 400 / Turbo 400

Replacing transmission gasket, pan and filter on my Turbo 400 or TH 400 transmission. One of many restoration tutorials on my 1969 Chevy C20.
Jegs Kit: www.jegs.com/i/JEGS/555/60118...
TH 400 Filter Spacer: www.monstertransmission.com/T...
-----------------------------------------------------------------------------------------------------------
Chapters
0:00 Intro
0:49 Take Out Old Stuff
1:44 Unbox Jegs Kit
1:58 Finish Prep
4:02 Assemble
6:23 Finish and Outro
Don't Forget to Like, Comment and Subscribe!
-----------------------------------------------------------------------------------------------------------
Info:
TH-cam Channel: / chrisncars
Website: chrisncars.com/
Mail: [e-mail]
Video: • Replace Transmission G...
This is one of many restoration videos I have made. More can be found here:
• WorkiN on Cars
-----------------------------------------------------------------------------------------------------------
Music:
♫ Track - Jamie Berry - Sweet Rascal
♫ Watch - • #ElectroSwing | Jamie ...
♫ Follow Jamie Berry
SoundCloud: / jamie-berry
#ChrisNCars #Transmission #DIY
-----------------------------------------------------------------------------------------------------------
Disclaimer:
Due to factors beyond the control of Chris N’ Cars, I cannot guarantee against improper use or unauthorized modifications of this information. Chris N’ Cars assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this information at your own risk. Chris N’ Cars recommends safe practices when working on vehicles and or with tools seen or implied in this video. Due to factors beyond the control of Chris N’ Cars, no information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. Any injury, damage, or loss that may result from improper use of these tools, equipment, or from the information contained in this video is the sole responsibility of the user and not Chris N’ Cars.

[@nolanscott9330]

Perfect Vid, nice and simple no extra stuff. This is quality stuff. And exactly what I needed.

[@ChrisNCars]

Thanks! Glad it helped.

[@georgeumstead2705]

Very nice and informative video. Thank you

[@albertrivera5443]

Very good video!! Thanks for posting!!

[@burlgoat53]

Great simple install.....doing mine tomorrow ...thanks sir !!!!!

[@ChrisNCars]

Good luck today!

[@Sadioli]

timing on this is great. TY!

[@ChrisNCars]

Hope it helps!

[@johnhenryholiday4964]

Excellent video.... I prefer to use the cork gasket which is what the trans came with.... Im sure that your rubber gasket worked equally as well....

[@ChrisNCars]

I prefer cork too this kit just came with rubber

[@Troy_Built]

Thanks it had been decades since I did a filter and gasket on a TH400. When I noticed how loose that filter was I wanted to quickly check something to make sure it was supposed to be like that.

[@moon27hall]

Curious, when u checked the fluid level at the end of the vid, was the engine running? Hard to tell. Thanks! Great vid btw.

[@ChrisNCars]

It was after running it through the gears for about 10 mins. The engine is off when I pulled the stick.

[@francoamerican4632]

What did you do with the debris magnet now that you're using an aluminum pan? Would like to see a video showing how to change a gasket on a turbo 400 on a 1969 Firebird. They have a cross member that prevents access to one of the pan bolts and are a MAJOR pain in the you know what.

[@ChrisNCars]

The bolt on new pan has a magnet. If someone lets me work on their firebird id do it!

[@johnhenryholiday4964]

Your car and a P-30 chassis share that same misfortune... that cross member is a major pain....

[@DUCKSAREEVILLLLLLLL]

@@johnhenryholiday4964 Here's what worked for my 1987 Mallard Class A P30 motorhome with a TH400. After spraying the bolt and hole with break clean as a kind of lube for the bolt thread (and to facilitate better grip of the hex side), start the bolt with left index finger from the cross member side and your right index finger from the passenger side. Once you have it almost touching the pan, access the bolt from inside the cross member with a box end 12 sided wrench. There was enough room that I was able to use my Sears long 13MM wrench to tighten it. To loosen it, I used a long, U-shaped wrench from "Powercraft" or something, but I think loosening the bolt from inside the crossmember would have been MUCH easier.

[@SILENTKILLA972]

What size is that gasket I have mine leaking from the drain plug but not sure exactly what size it is

[@ChrisNCars]

Sorry not sure the plug came with the pan kit

[@SILENTKILLA972]

@@ChrisNCars that's ok I called and asked its 1/2 20 threads so the ID of gasket would be 1/2

[@davidrowland2354]

Need 6 quarts

[@-COOL-ARROWS-GARAGE]

Any leaks yet?

[@West_Coast_Ganbaru]

. . .the filter is supposed to be able to move around. It's NOT supposed to sit snug. It is designed to float in the surface of the fluid.

[@ChrisNCars]

I remade this video because everyone was giving me crap for letting it float in the first rendition 🤦‍♂

[@West_Coast_Ganbaru]

@ChrisNCars its okay. I didn't mean to sound so rude, and I apologize. Your original video was correct. The filter is supposed to float freely, hence the amount of play on the singular bolt. When know-it-alls come to your comment section just hit them with facts from the manufacturer.

[@ChrisNCars]

@@West_Coast_Ganbaru yeah, haha! I mean that's what I get for posting on youtube. But, it also helps me be better at working on cars and making videos!

[@Michael-B41]

Advice dont use the paper filters go with screen type allison and double o ring filter tube case side

[@DUCKSAREEVILLLLLLLL]

I've heard 12 ft lbs torque, and now 18. Hmm...

[@ChrisNCars]

Either isn’t much

[@mitchg5809]

First 👍

[@ChrisNCars]

Ha! Nice!