Thank you Mr. Haseb for sharing your knowledge. I have learned very much from these two videos and from others. I encourage you to continue delighting us with more videos.
اسلام عليكم ورحمة الله وبركاته Thank you so much mr haseeb may Allah gives you long life with good health I really like the way u teach I wish you be my teacher my name is salieu and I live in Mauritania and I think you again for rectifying people's 👏👏👏👏👏👏
Excellent brother tutorial we expecting more from you I request to you Can you do complete fault finding and working principle of Inverter Air conditioner Pcb video Please
Hi Haseeb and thank you so much for all your excellent videos! I have learned so much from all your SMPS videos and now about refrigerator inverter boards. When you have some time, would you consider doing a video on refrigerator main control circuit boards? I’m having some problems with mine and would like to understand more about how it operates. Thanks again so much and take care!
Hi Haseeb, you are using probably isolating transformer for your scope? otherwise you can’t use Oscilloscop connected to ground without blowing fuse or demaged your scope
yes brother i am using isolation transformer i recorded a detailed video, it is now in editing it will be uploaded next week please check 468 & 469 on the same topic
Thankyou for the tutorial. I learnt that the input voltage to the VCC is 230V. I also learnt that the control votage is 3V. In a good VCC what is the voltage at each connection to the compressor?
HI. Thanks for your videos. These are very helpful. How and would it be practical to convert a VCC3 220VAC(2456) to 120VAC(1156)? I use the 120VAC(1156) but the 220 VAC(2456) are less expensive to buy for some reason. TIA.
9:20 - Tell me where you have your scope grounded, please. I have viewed several times and I am unable to see it. Also, is your scope battery operated? Also, thank you for allowing CC. It makes it easier to understand if I missed a word you spoke.
Awesome very nice informative vedio my dearest brother big thumbs up from me. thanks for sharing the details of the job.be happy with good health and happiness ameen 🛏️.
Hello Haseeb, I used a wave meter to measure 3 pins u, v, w and the results were normal. but my compressor still doesn't work, just vibrates then turns off, my compressor uses Jiaxipera, the compressor light flashes 9 times. Have you encountered this situation? I hope you will release a video about VCC3 Compressor Jiaxipera DC Inverter. Thanks
if the board have 2 capacitors, then you can use that central pins of capacitor can be grounded but some boards have voltage sensing line, which gives the voltage sensing a voltage divider network. in that case you have to redesign that voltage divider network to give voltage value to microcontroller
@@HaseebElectronics Oh I think I see the "voltage sense line" is sensing the voltage of the bulk capacitor and connected to microcontroller ADCIN0. ? R115(620K), R116(620K),R117(620K),R103(12K) are the divider?
@@HaseebElectronics If I am looking at the right divider resistors R115,R116,R117,R103 then interesting - they are the same value on the 220VAC(2456) inverter as the 110VAC(1156) inverter. The 110VAC(1156) has 2 capacitors 820uF/200V. The 220VAC(2456) has 1 capacitor 400V/220uF.
wonderful. done boards have this vsense pin voltage divider different than 220 now you can modify it easily if the 400v/220 if have connection points on the board for another capacitor then install another 200 volt capacitor and take the central common point of capacitors to the bridge input line and modify the input circuit as the 110 volt board
Hello. Please tell me the specifications of this diode. No matter what I tried, I did not get results. zd is written on the board, which should be a zener diode. The part number on the diode is 5AY. This diode is related to the inverter board of the refrigerator compressor. Thanks
hi , thanks for exponation , I want to tell a question . I have a board like this but in dc tension don't have 330 VDC but tension isn't stable. i get 300V 290V . there is something no working .Cold u please tell me somthing about that problem ? thank a lot
@@HaseebElectronics is a 220 V ac , I try to replace main capacitor with another with more microfar but its the same thing , mosfet at first impression with multimetr sound like good .
Sir mera aap say siraf aik question ha woo yea k Kya aap oscilloscope ki setting iss tarah btaa sakty hain k humay haar daffaaa Auto ka button press na krnaa pardy plz iss tarah ki koi settings btaa dein Shukriyaa Sir G.......... Jiss tarah hum multimeter ko DC range per set kr uss say DC voltage read krty hain uss kee range k mutabik iss tarah oscilloscope ki a6i c settings btaa dein...... Sir mein nay Inverter AC kee Kit or Embraco inverter board test krny hain plz reply Sir Shukriyaa ❣️
اسلام عليكم ورحمة الله وبركاته I have a vcc31156 and my input voltage is 120v I measured my voltage on the compressor phase line and is giving me 330v an220v but mv millie volt does that mean the board is still good?
you are right. if the protection diode is short internally then at full 3 phase operation the load arrives at main capacitor so tge DC rail fuse blows up in that case. and the echo signal to the microcontroller is hang. so the microcontroller cannot generate the next stepping pulse
Sir iss per or mazzedd videos bnayaaa plz plz plz plz sir it's a request Embraco k inverter board per or Videos bnayee plz plz plz plz plz plz plz ❣️🥰❣️
Sir help me my inverter board PCB not passing current to compressor MOSFET and capacitors are good which components have fault and how can I check that help me
you are right. it starts and waits for the feedback through its sense lines which are connected to UVW lines through resistors if compressor is not connected, that time the MCU disconnects the drive in few seconds
I have problem DC invertor board VCC3 3456 F4 , I have negative signal half curve only , Follow this video i have change IR 2304 ic but still same. Input pin 3 i get 15~16VOLT.Can you help me
Hi there.....i hope you can help me out to save some money. I live in Europe. I have a siemens inverter refrigerator. 2 months before it stops working and the motor does a like week 'bzzzzz' sound. I am amateur in this things but i have a hakko soldering iron and a fluke 179 multimeter and i know/have a little practice about soldering/desoldering. I have test all the 33uf electrolytic capacitors. 3 of the capacitors have regular values, +/-5%. One of them have if i remember right is 584 uf and the other about 48uf. I changed the 2 "faulty" capacitors and voila....nothing happended.....same as before. The reading of the new capacitors are equal with the old original ones that i repleace (high- 584-48uf). I notice that when i measure these 2 capacitors soldered in the board values are high, but when i dessolder it and test it again off the board the values are correct. Also the 2 'old' original capacitors that i took off the board have the right values 31.8/32.5 uf. I don't know what to do, should i replace and the other 33uf capacitors or no? Please help me my friend!
1st helpful and informative share as always
thanks for pinned
Suche or imandar bande ki ye nishani hai k wo bhot he ache tareeke se kam kare or wo ap men Sab wo kobhi hai brother big like salam
*Great Dear very nice upload lk*
Very useful and informative video. Aap hamesha hi bahut hi achchhi jankari dete hai
Walekum assalam. Very nice this video 5:20
Thank you Mr. Haseb for sharing your knowledge. I have learned very much from these two videos and from others. I encourage you to continue delighting us with more videos.
اسلام عليكم ورحمة الله وبركاته
Thank you so much mr haseeb may Allah gives you long life with good health I really like the way u teach I wish you be my teacher my name is salieu and I live in Mauritania and I think you again for rectifying people's 👏👏👏👏👏👏
Like 24,very nice and beautiful video beautiful sharing mashaallh khubsurt video beautiful sharing zbrdst stay connected please
Like 28 , very nice , fantastic info sharing 👌👌👌 so useful , nice to know 👌👌👌👌 awesome share 💐💐
Video quality is awesome and very helpful video
NYC sharing
Thank you very much Mr Haseeb for your efforts. Good method of faulty signal analysis. عليكم السلام و رحمة الله تعالى وبركاته.شكرا
Very good repair
Excellent brother tutorial we expecting more from you I request to you Can you do complete fault finding and working principle of Inverter Air conditioner Pcb video Please
Thank you brother for your patience and helpful videos.
Please accept my best regards and special thanks ❤️
Wa alaikum asalam. Great knowledge 👍👍great sharing jazak Allah
very useful information thank you so much. please explain all types of transistors working and how to check
Hi Haseeb and thank you so much for all your excellent videos! I have learned so much from all your SMPS videos and now about refrigerator inverter boards. When you have some time, would you consider doing a video on refrigerator main control circuit boards? I’m having some problems with mine and would like to understand more about how it operates. Thanks again so much and take care!
thanks a lot for your valuable comment
Great suggestion! i will try my best to arrange it
@@HaseebElectronics Thanks so much for considering this!
Hi Haseeb, you are using probably isolating transformer for your scope? otherwise you can’t use Oscilloscop connected to ground without blowing fuse or demaged your scope
yes brother
i am using isolation transformer
i recorded a detailed video, it is now in editing
it will be uploaded next week
please check 468 & 469 on the same topic
Thankyou for the tutorial. I learnt that the input voltage to the VCC is 230V. I also learnt that the control votage is 3V. In a good VCC what is the voltage at each connection to the compressor?
Sir I learn more from you .Thank you very much.
It's my pleasure
HI. Thanks for your videos. These are very helpful. How and would it be practical to convert a VCC3 220VAC(2456) to 120VAC(1156)? I use the 120VAC(1156) but the 220 VAC(2456) are less expensive to buy for some reason. TIA.
Very nice and technical vlog. Thank you for sharing. Have a good day.
💕💖💞
On Kar k rakh dia hai. Full play k liyay.
Thanks for sharing informative and helpful tips.
Master..good video..i wants learn more
hi sir at 22:30 is using SCOPE the ONLY way to test the output of the ic? i dont have a scope can i use a multimeter instead?
Sir thank you sharing idea I have learned so much. Helpful and informative
best regards
like 12
very informative and useful video thanks for sharing
Wa Alaikhum Slam!
Very informative video
Thanks for Sharing
Excellent waiting for this video hats off brother
A.OA sir how did u ON the pcb. Without compressor the processor will not out the gate signal upto my experience. Thanks
Plz app always video urdu mein bnaya kro sab ko samaj aa ay gi ..thanks
Ji bhai
urdu me meri videos mere doosrey channel (haseeb electronics urdu) per upload hoti hein
9:20 - Tell me where you have your scope grounded, please. I have viewed several times and I am unable to see it. Also, is your scope battery operated?
Also, thank you for allowing CC. It makes it easier to understand if I missed a word you spoke.
Check and pause at 10:46 you will see a gray wire connected to test pin
Very useful electronic circuit guide. Thank you for sharing offline
So useful 👌
boa noite sou do Brasil onde vc ligou o 2 fios que envia o sinal para acionar o motor
Cám ơn thật nhiều. Chúc gia đình Anh sức khoẻ
The video was good, can you show us how to test a IC P1941 with seven pongs the number six pong is not ues?
Very clear explanation.Thank you!!
Awesome very nice informative vedio my dearest brother big thumbs up from me. thanks for sharing the details of the job.be happy with good health and happiness ameen 🛏️.
Sir good day
I'm just asking, how many five DC volt in one board of Aircon unit? Thanks gooday😊
IK 27 good sharing 👍🌹
Beautiful video Haseeb, interesting Repair VCC3♫
going to greet, big sunday, thumbs up!!!!
Hello Haseeb, I used a wave meter to measure 3 pins u, v, w and the results were normal. but my compressor still doesn't work, just vibrates then turns off, my compressor uses Jiaxipera, the compressor light flashes 9 times. Have you encountered this situation? I hope you will release a video about VCC3 Compressor Jiaxipera DC Inverter. Thanks
Great explanation. 👍👍
Thanks sir of make this video 🤝🤝
Hi. Thanks for your videos. Is there a practical method to convert the VCC3/220VAC to operate with 120VAC? TIA
if the board have 2 capacitors, then you can use that central pins of capacitor can be grounded
but some boards have voltage sensing line, which gives the voltage sensing a voltage divider network. in that case you have to redesign that voltage divider network to give voltage value to microcontroller
@@HaseebElectronics Oh I think I see the "voltage sense line" is sensing the voltage of the bulk capacitor and connected to microcontroller ADCIN0. ?
R115(620K), R116(620K),R117(620K),R103(12K) are the divider?
@@rogerschelling3162 yes there is special line to check the dc voltage to adjust frequency and voltage
@@HaseebElectronics If I am looking at the right divider resistors R115,R116,R117,R103 then interesting - they are the same value on the 220VAC(2456) inverter as the 110VAC(1156) inverter.
The 110VAC(1156) has 2 capacitors 820uF/200V. The 220VAC(2456) has 1 capacitor 400V/220uF.
wonderful. done boards have this vsense pin voltage divider different than 220
now you can modify it easily
if the 400v/220 if
have connection points on the board for another capacitor
then install another 200 volt capacitor
and take the central common point of capacitors to the bridge input line
and modify the input circuit as the 110 volt board
Hello. Please tell me the specifications of this diode. No matter what I tried, I did not get results. zd is written on the board, which should be a zener diode. The part number on the diode is 5AY. This diode is related to the inverter board of the refrigerator compressor. Thanks
Good morning 😁 awsome 🌼
thanks for sharing this video it is very helpful but can please do other video after you repair that inverte pcb. thanks
next part is coming on sunday morning
@@HaseebElectronics thank you sir because i want to learn more in the inverter circuits.
بارك الله فيكم
You are the best👌
i am thankful
Thumbs up done sir is there a build in photo triac at tny 254 ic tnv sir
Bohat achi vedio hai sir aapki shop kahan hain?kya aap serves dety hain?
hi , thanks for exponation , I want to tell a question . I have a board like this but in dc tension don't have 330 VDC but tension isn't stable. i get 300V 290V . there is something no working .Cold u please tell me somthing about that problem ? thank a lot
@@HaseebElectronics is a 220 V ac , I try to replace main capacitor with another with more microfar but its the same thing , mosfet at first impression with multimetr sound like good .
Very helpful and nice information shared like always. Keep it up bro.
Great Video
like 36 full watched
Please advise if you have any other simple method to test this circuit without the motor used for this.
بالتوفيق والنجاح الباهر باذن الله 👍
Sir mera aap say siraf aik question ha woo yea k
Kya aap oscilloscope ki setting iss tarah btaa sakty hain k humay haar daffaaa Auto ka button press na krnaa pardy plz iss tarah ki koi settings btaa dein Shukriyaa Sir G..........
Jiss tarah hum multimeter ko DC range per set kr uss say DC voltage read krty hain uss kee range k mutabik iss tarah oscilloscope ki a6i c settings btaa dein......
Sir mein nay Inverter AC kee Kit or Embraco inverter board test krny hain plz reply Sir Shukriyaa ❣️
Hi do you know of a good tester kit for testing these compressors?
اسلام عليكم ورحمة الله وبركاته I have a vcc31156 and my input voltage is 120v I measured my voltage on the compressor phase line and is giving me 330v an220v but mv millie volt does that mean the board is still good?
my friend the igbt module maybe there are shorted diode inside thats why the output voltage drop..u can hang the output signal to ipm
you are right. if the protection diode is short internally then at full 3 phase operation the load arrives at main capacitor so tge DC rail fuse blows up in that case. and the echo signal to the microcontroller is hang. so the microcontroller cannot generate the next stepping pulse
Sir if I want any ic datasheet which website I can preferred?
Good vdo
Very informative
thanks a lot
Good video
Please do inverter aircon shunt and comparator how works and fault finding
Hi Why one of the IGBT's get fail in one phase. this in Hisens Inverter Refrigerator inverter PCB
Sir iss per or mazzedd videos bnayaaa plz plz plz plz sir it's a request Embraco k inverter board per or Videos bnayee plz plz plz plz plz plz plz ❣️🥰❣️
agr aap Pakistan se hein to mujhey WhatsApp 00962781161084 kr dein please
THX . Brother AC Inverter per bi video banaye aasi urdu may
Thank you!
thanks a lot
Fully watched
Good very nice
Very good explanation Sir may I know what the number of the three driver ic tnx for your reply Sir
@@HaseebElectronics Thank you so much Sir
اتمني لكم التوفيق 🌹🌹 والنجاح الدائم
Thank you so much sir..
Most welcome
Big like keep visiting
Sir help me my inverter board PCB not passing current to compressor MOSFET and capacitors are good which components have fault and how can I check that help me
Sir please can you tell me
The part numbers of n channel and p channel mosfett in that vcc3 ... thankyou
excellent
Many many thanks
How to this pcb run with out compressor .i think this type PCB to run must wont compressor feed back voltage for run micro control
you are right. it starts and waits for the feedback through its sense lines which are connected to UVW lines through resistors
if compressor is not connected, that time the MCU disconnects the drive in few seconds
@@HaseebElectronics
i need run without compressor for test this type pcb.can i run 1mite this pcb.please help me....
Very informative but should have tested the pin 7 out put side of the other two ic which you said is working.
Yes, you are right
i will share again in upcoming days
Assalamualaikum, sir would you please explain 555 ic.
yes brother i will try to do it soon
Amazing upload
Thanks sir good good good
Most welcome
*good 👍👍✅🙏🏻*
Great Video
like 36
Thank you for sharing I wish you
a wonderful Time - Gretings :))~Sara~
Could u please one problem ,gree odu when I test it without compressor was normal but I connect with compressor make the ipm broken
@@HaseebElectronics really thank u very much
Hi Bro, All output driver ic LIN,HIN no input 18V why please help
I have problem DC invertor board VCC3 3456 F4 , I have negative signal half curve only , Follow this video i have change IR 2304 ic but still same. Input pin 3 i get 15~16VOLT.Can you help me
can you please check the return feedback to microcontroller (from output terminals through resistor network
@@HaseebElectronics # Hi sir, Output signal from Triac ? Any output signal from IRS2304S ic to microcontroller need to measure ?
So informative
I'm jassi india I'm so happey to you
Hi there.....i hope you can help me out to save some money. I live in Europe. I have a siemens inverter refrigerator. 2 months before it stops working and the motor does a like week 'bzzzzz' sound. I am amateur in this things but i have a hakko soldering iron and a fluke 179 multimeter and i know/have a little practice about soldering/desoldering. I have test all the 33uf electrolytic capacitors. 3 of the capacitors have regular values, +/-5%. One of them have if i remember right is 584 uf and the other about 48uf. I changed the 2 "faulty" capacitors and voila....nothing happended.....same as before. The reading of the new capacitors are equal with the old original ones that i repleace (high- 584-48uf). I notice that when i measure these 2 capacitors soldered in the board values are high, but when i dessolder it and test it again off the board the values are correct. Also the 2 'old' original capacitors that i took off the board have the right values 31.8/32.5 uf. I don't know what to do, should i replace and the other 33uf capacitors or no?
Please help me my friend!
@@HaseebElectronics Embraco QD VCC3 2456 A1
Kabhi Kabhi Urdo Mein Bhi Upload Kar Diya karen Mere Jeson Ke Liye RAB Rakha Mere Bhai
MOLTO UTILE! VORREI COSTRUIRE UNA SCHEDA DA PORTARE CON ME PER PROVARE IL COMPRESSORE DEL FRIGORIFERO INVERTER IN CASA DEL CLIENTE
i migliori saluti. è un piacere che il mio lavoro sia utile. rimani benedetto
احلى بصمة👍
walekum assalam,
all three driver ics are faulty? something missing bhai.
عليكم السلام ورحمة الله ويركاته