The Broken Front Wheel spindle Reattached from Basic Tool And Heavy truck wheel Bolt Repair process
ฝัง
- เผยแพร่เมื่อ 10 ก.ย. 2024
- The Broken Front Wheel spindle Reattached from Basic Tool And Heavy truck wheel Bolt Repair process
#Brokenfrontwheelspindle
#Reattchedbrokenspindle
#wheelboltrepair
#ultimateprocess
It’s like this, you can weld anything together and look nice and pretty, but unless strict adherence to repair material, weld material weld pre-heat and post weld heat treatment it is at best an unreliable repair. In this case, a wheel axle would make it a dangerous thing to repair in this way! Anyone watching don’t take this as a way to repair an axle!
Excelente trabajo, muy buena técnica, felicitaciones por su taller todo muy limpió y ordenado, eres un profesional
Why didn't you just make a new stud out of the one piece bar that you use to make the patch. It would be stronger and easier if you had just make a new one piece stud .
It seems like a good job but in the first part there is no heat treatment at the end and no information about the quality of the steel used for the repair. In the second part it is easier to make a new part with stronger steel!!! Now I know why there are so many accidents in this country......
Молодцы муж ки спецы своего дела нравится что без лишних разговоров и без промедления увидел взялся и сделал
I don't know from where are you, but probably there are more accidents in your country. On the other end, there are no statistics about accidents caused by original or rebuilt/repaired parts
why do these keep breaking, well...... ut was "fixed " once before
Gets worse!! The original was a solid axle. This crappy one has nothing in the center---only about 2/3 weld. This DANGEROUS
To my friend Oliver! You are watching Pakistan. According to WHO in 2019, Pakistan had roughly 28,000 accidents per 100,000 while USA had 45,000 however INDIA had 212,000 accidents /100,000 I think you are referring to India when you said that therefore this country has more accidents? I am not trying to belittle India or any other country for that matter but correcting the facts but you must also consider India has very large population (greater then one billions, while China even bigger then India has about 250,000)
Se tarda menos comprar la pieza nueva buenas noches
Wouldn’t it have been easier to chuck up on the inside bearing diameter and then drill thru from kingpin side for the new spindle? Still questionable repair for a truck that will see overloads and rough roads.
very good un lavoro che voi indiani sapete far bene 👍👍👍
Excelente trabalho 👏👏😊
Good stuff 👌🎉
최고입니다. 🤩
you cannot weld and repair forged material and expect it to work, it mat look good but structurally it is is incredibly weak. the repair they use just isn't going to work.
Es mejor meter con una prensa hidráulica antes que golpear la pieza, por el cabezal del torno...mi modesta opinion
👍👍👍👍
😲
Amazing! Very good work!
Burada tamirin kalitesinden önce, tamirden sonra üzerine binecek aşırı yükten bahsetmek daha doğru olacaktır.. Aksın yük kapasitesi belki 10 ton, sonradan üzerine bindirilecek olan yük 25 ton!!!!!! Mesele burada….😊😊
Excellent job.
They did good work
Any drive motor vehicles not allowed such a idiotic work due to life threat passenger, people drivers are in life in danger
I watched that “parting-off” tool wobble like an old wet straw and thought…great machinist …NOT!
учитывая следы от УШМ на валу (22 секунда) они сами распиливают зап. части для контента. Просмотры сами себя не сделают.
always seem to be the same bus
Скоро эти ребята завалят наши рынки своми изделиями еще каки то пору лет и увидим их в в доказательство наши институты заполнены ребятами из этой страны ))
💎⭐⭐⭐⭐⭐
💯
salam vean y aprendan
These guys should be stopped for this dangerous BS work. There is no way that they can make this repair to anywhere near the strength of the original part.
And the idiot drivers managed to break that, so what chance does this one have? Of course, the is chance that this has been broken before, repaired the same way, and br4oke again, just like this one will.
Bad workmanship, as any competant welder would not take the job in the first place
🙅🏾♂️❌🚫🥽🕶️